1 files changed, 0 insertions, 145 deletions
diff --git a/board/dibbi/board.h b/board/dibbi/board.h
deleted file mode 100644
index c59a540b5d..0000000000
--- a/board/dibbi/board.h
+++ /dev/null
@@ -1,145 +0,0 @@
-/* Copyright 2022 The ChromiumOS Authors
- * Use of this source code is governed by a BSD-style license that can be
- * found in the LICENSE file.
- */
-
-/* Dibbi board configuration */
-
-#ifndef __CROS_EC_BOARD_H
-#define __CROS_EC_BOARD_H
-
-/* Select Baseboard features */
-#define VARIANT_DEDEDE_EC_IT8320
-#include "baseboard.h"
-
-/* System unlocked in early development */
-#define CONFIG_SYSTEM_UNLOCKED
-
-#define CONFIG_CMD_CHARGER_DUMP
-
-/* Power */
-#undef CONFIG_CHARGER
-#undef CONFIG_CHARGER_DISCHARGE_ON_AC
-#undef CONFIG_USB_PD_VBUS_MEASURE_CHARGER
-#define CONFIG_CHARGER_MIN_POWER_MW_FOR_POWER_ON 16000
-#define PD_MAX_VOLTAGE_MV 15000
-#define CONFIG_USB_PD_VBUS_DETECT_GPIO
-/* ADC sensors could measure VBUS on this board, but components are DNS */
-#define CONFIG_USB_PD_VBUS_MEASURE_NOT_PRESENT
-
-/* Override macro for C0 only */
-#define PORT_TO_HPD(port) (GPIO_USB_C0_DP_HPD)
-
-/* Power: Dedicated barreljack charger port */
-#undef CONFIG_DEDICATED_CHARGE_PORT_COUNT
-#define CONFIG_DEDICATED_CHARGE_PORT_COUNT 1
-#define DEDICATED_CHARGE_PORT 1
-
-/* USB Type-C */
-#undef CONFIG_USB_CHARGER
-#undef CONFIG_USB_MUX_PI3USB31532
-
-/* TCPC */
-#define CONFIG_USB_PD_PORT_MAX_COUNT 1
-#define CONFIG_USB_PD_TCPM_ITE_ON_CHIP /* C0: ITE EC TCPC */
-#define CONFIG_USB_PD_ITE_ACTIVE_PORT_COUNT 1
-
-/* USB Mux and Retimer */
-#define CONFIG_USB_MUX_IT5205 /* C0: ITE Mux */
-#define I2C_PORT_USB_MUX I2C_PORT_USB_C0 /* Required for ITE Mux */
-
-/* USB Type A Features */
-#define CONFIG_USB_PORT_POWER_DUMB
-#define USB_PORT_COUNT 3 /* Type A ports */
-
-/* No battery */
-#undef CONFIG_BATTERY_CUT_OFF
-#undef CONFIG_BATTERY_PRESENT_GPIO
-#undef CONFIG_BATTERY_REQUESTS_NIL_WHEN_DEAD
-#undef CONFIG_BATTERY_REVIVE_DISCONNECT
-#undef CONFIG_BATTERY_SMART
-
-/* LED */
-/* TODO(b/259467280) Determine what LED/PWM impl is needed*/
-/* #define CONFIG_LED_PWM */
-/* #define CONFIG_LED_PWM_COUNT 1 */
-
-/* PWM */
-#define CONFIG_PWM
-
-/* Thermistors */
-#define CONFIG_TEMP_SENSOR
-#define CONFIG_THERMISTOR
-#define CONFIG_STEINHART_HART_3V3_51K1_47K_4050B
-
-/* Buttons */
-#define CONFIG_DEDICATED_RECOVERY_BUTTON
-#define CONFIG_DEDICATED_RECOVERY_BUTTON_2
-#define CONFIG_POWER_BUTTON
-#define CONFIG_POWER_BUTTON_IGNORE_LID
-#define CONFIG_POWER_BUTTON_X86
-
-/* No Keyboard */
-#undef CONFIG_MKBP_EVENT
-#undef CONFIG_MKBP_EVENT_WAKEUP_MASK
-#undef CONFIG_MKBP_USE_GPIO_AND_HOST_EVENT
-#undef CONFIG_KEYBOARD_COL2_INVERTED
-#undef CONFIG_KEYBOARD_PROTOCOL_8042
-#undef CONFIG_MKBP_INPUT_DEVICES
-#undef CONFIG_CMD_KEYBOARD
-#undef CONFIG_KEYBOARD_BOOT_KEYS
-#undef CONFIG_KEYBOARD_RUNTIME_KEYS
-
-/* No backlight */
-#undef CONFIG_BACKLIGHT_LID
-#undef GPIO_ENABLE_BACKLIGHT
-
-/* Unused features - Misc */
-#undef CONFIG_HIBERNATE
-#undef CONFIG_VOLUME_BUTTONS
-#undef CONFIG_LID_SWITCH
-#undef CONFIG_TABLET_MODE
-#undef CONFIG_TABLET_MODE_SWITCH
-#undef CONFIG_GMR_TABLET_MODE
-#undef GPIO_TABLET_MODE_L
-
-/* Unused GPIOs */
-#undef GPIO_USB_C1_DP_HPD
-
-/* Pin renaming */
-#define GPIO_RECOVERY_L GPIO_EC_RECOVERY_BTN_ODL
-#define GPIO_RECOVERY_L_2 GPIO_H1_EC_RECOVERY_BTN_ODL
-#define GPIO_POWER_BUTTON_L GPIO_H1_EC_PWR_BTN_ODL
-
-#ifndef __ASSEMBLER__
-
-#include "gpio_signal.h"
-#include "registers.h"
-
-enum charge_port {
-	CHARGE_PORT_TYPEC0,
-	CHARGE_PORT_BARRELJACK,
-};
-
-enum pwm_channel {
-	PWM_CH_LED_RED,
-	PWM_CH_LED_GREEN,
-	PWM_CH_LED_BLUE,
-	PWM_CH_COUNT,
-};
-
-/* ADC channels */
-enum adc_channel {
-	ADC_VSNS_PP3300_A, /* ADC0 */
-	ADC_TEMP_SENSOR_1, /* ADC2 */
-	ADC_TEMP_SENSOR_2, /* ADC3 */
-	ADC_PPVAR_PWR_IN_IMON, /* ADC15 */
-	ADC_SNS_PPVAR_PWR_IN, /* ADC16 */
-	ADC_CH_COUNT
-};
-
-enum temp_sensor_id { TEMP_SENSOR_1, TEMP_SENSOR_2, TEMP_SENSOR_COUNT };
-
-#endif /* !__ASSEMBLER__ */
-
-#endif /* __CROS_EC_BOARD_H */