1 files changed, 0 insertions, 92 deletions
diff --git a/board/elm/usb_pd_policy.c b/board/elm/usb_pd_policy.c
deleted file mode 100644
index 2eeab736d9..0000000000
--- a/board/elm/usb_pd_policy.c
+++ /dev/null
@@ -1,92 +0,0 @@
-/* Copyright 2016 The Chromium OS Authors. All rights reserved.
- * Use of this source code is governed by a BSD-style license that can be
- * found in the LICENSE file.
- */
-
-#include "atomic.h"
-#include "charge_manager.h"
-#include "common.h"
-#include "console.h"
-#include "driver/tcpm/anx7688.h"
-#include "driver/tcpm/tcpci.h"
-#include "driver/tcpm/tcpm.h"
-#include "gpio.h"
-#include "hooks.h"
-#include "host_command.h"
-#include "registers.h"
-#include "system.h"
-#include "task.h"
-#include "timer.h"
-#include "util.h"
-#include "usb_mux.h"
-#include "usb_pd.h"
-
-#define CPRINTF(format, args...) cprintf(CC_USBPD, format, ## args)
-#define CPRINTS(format, args...) cprints(CC_USBPD, format, ## args)
-
-int pd_set_power_supply_ready(int port)
-{
-	/* Disable charging */
-	gpio_set_level(GPIO_USB_C0_CHARGE_L, 1);
-	/* Provide VBUS */
-	gpio_set_level(GPIO_USB_C0_5V_EN, 1);
-
-	anx7688_set_power_supply_ready(port);
-
-	/* notify host of power info change */
-	pd_send_host_event(PD_EVENT_POWER_CHANGE);
-
-	return EC_SUCCESS;
-}
-
-void pd_power_supply_reset(int port)
-{
-	/* Disable VBUS */
-	gpio_set_level(GPIO_USB_C0_5V_EN, 0);
-
-	anx7688_power_supply_reset(port);
-
-	/* notify host of power info change */
-	pd_send_host_event(PD_EVENT_POWER_CHANGE);
-}
-
-int pd_check_vconn_swap(int port)
-{
-	/* in G3, do not allow vconn swap since 5V power source is off */
-	return gpio_get_level(GPIO_5V_POWER_GOOD);
-}
-
-/* ----------------- Vendor Defined Messages ------------------ */
-#ifdef CONFIG_USB_PD_ALT_MODE_DFP
-__override int svdm_dp_attention(int port, uint32_t *payload)
-{
-	int cur_lvl;
-	int lvl = PD_VDO_DPSTS_HPD_LVL(payload[1]);
-	int irq = PD_VDO_DPSTS_HPD_IRQ(payload[1]);
-	int ack = 1;
-
-	anx7688_update_hpd(port, lvl, irq);
-
-	dp_status[port] = payload[1];
-	cur_lvl = gpio_get_level(GPIO_USB_DP_HPD);
-
-	/* Its initial DP status message prior to config */
-	if (!(dp_flags[port] & DP_FLAGS_DP_ON)) {
-		if (lvl)
-			dp_flags[port] |= DP_FLAGS_HPD_HI_PENDING;
-		return ack;
-	}
-
-	if (!(irq & cur_lvl) && irq & !cur_lvl) {
-		CPRINTF("ERR:HPD:IRQ&LOW\n");
-		ack = 0; /* nak */
-	}
-	/* ack */
-	return ack;
-}
-
-__override void svdm_exit_dp_mode(int port)
-{
-	anx7688_hpd_disable(port);
-}
-#endif /* CONFIG_USB_PD_ALT_MODE_DFP */