diff options
Diffstat (limited to 'board/endeavour/gpio.inc')
| -rw-r--r-- | board/endeavour/gpio.inc | 93 |
1 files changed, 0 insertions, 93 deletions
diff --git a/board/endeavour/gpio.inc b/board/endeavour/gpio.inc deleted file mode 100644 index 85904aab0c..0000000000 --- a/board/endeavour/gpio.inc +++ /dev/null @@ -1,93 +0,0 @@ -/* -*- mode:c -*- - * - * Copyright 2019 The Chromium OS Authors. All rights reserved. - * Use of this source code is governed by a BSD-style license that can be - * found in the LICENSE file. - */ - -/* Declare symbolic names for all the GPIOs that we care about. - * Note: Those with interrupt handlers must be declared first. */ - -GPIO_INT(AC_PRESENT, PIN(C, 1), GPIO_INT_BOTH, extpower_interrupt) -GPIO_INT(POWER_BUTTON_L, PIN(0, 4), GPIO_INT_BOTH | GPIO_PULL_UP, power_button_interrupt) /* MECH_PWR_BTN_ODL */ - -GPIO_INT(PCH_SLP_S0_L, PIN(7, 5), GPIO_INT_BOTH, power_signal_interrupt) -GPIO_INT(PCH_SLP_S3_L, PIN(7, 3), GPIO_INT_BOTH, power_signal_interrupt) -GPIO_INT(PCH_SLP_S4_L, PIN(8, 6), GPIO_INT_BOTH, power_signal_interrupt) -GPIO_INT(PCH_SLP_SUS_L, PIN(6, 2), GPIO_INT_BOTH, power_signal_interrupt) -GPIO_INT(RSMRST_L_PGOOD, PIN(B, 0), GPIO_INT_BOTH, power_signal_interrupt) -GPIO_INT(PMIC_DPWROK, PIN(C, 7), GPIO_INT_BOTH, power_signal_interrupt) -GPIO_INT(WP_L, PIN(9, 3), GPIO_INT_BOTH, switch_interrupt) -GPIO_INT(RECOVERY_L, PIN(8, 2), GPIO_INT_BOTH, button_interrupt) /* Recovery button */ - -/* TODO(jnchase): configure as interrupt when code is ready / if needed*/ -GPIO(POE_LTC_PGOOD, PIN(C, 5), GPIO_INPUT) /* PoE power good */ -GPIO(PSE_PWM_INT, PIN(3, 7), GPIO_INPUT) /* PoE LTC interrupt */ -GPIO(V3P3A_I350_PG, PIN(4, 4), GPIO_INPUT) /* Disconnected */ -GPIO(USB_C0_VBUS_DET_L, PIN(9, 7), GPIO_INPUT) /* USB-C VBUS */ -GPIO(USB_C0_POL_L, PIN(3, 3), GPIO_INPUT | GPIO_SEL_1P8V) /* USB-C Polarity */ - -GPIO(PCH_RTCRST, PIN(E, 7), GPIO_OUT_LOW) /* RTCRST# to SOC */ -GPIO(WLAN_OFF_L, PIN(7, 2), GPIO_OUT_LOW) /* Disable WLAN */ -GPIO(PP3300_DX_WLAN, PIN(A, 7), GPIO_OUT_LOW) /* Enable WLAN 3.3V Power */ -GPIO(CPU_PROCHOT, PIN(8, 1), GPIO_OUT_HIGH) /* PROCHOT# to SOC */ -GPIO(PCH_ACPRESENT, PIN(5, 0), GPIO_ODR_LOW) /* ACOK to SOC */ -GPIO(PCH_WAKE_L, PIN(A, 3), GPIO_ODR_HIGH) /* Wake SOC */ -GPIO(PCH_RSMRST_L, PIN(7, 0), GPIO_OUT_LOW) /* RSMRST# to SOC */ -GPIO(PCH_PWRBTN_L, PIN(7, 4), GPIO_ODR_HIGH) /* Power Button to SOC */ -GPIO(EC_PLATFORM_RST, PIN(4, 5), GPIO_OUT_LOW) /* EC Reset to LDO_EN */ -GPIO(SYS_RESET_L, PIN(6, 1), GPIO_ODR_HIGH) /* Cold Reset to SOC */ -GPIO(PMIC_SLP_SUS_L, PIN(8, 5), GPIO_OUT_LOW) /* SLP_SUS# to PMIC */ -GPIO(CCD_MODE_ODL, PIN(6, 3), GPIO_INPUT) /* Case Closed Debug Mode */ -GPIO(EC_HAVEN_RESET_ODL, PIN(0, 2), GPIO_ODR_HIGH) /* H1 Reset */ -GPIO(ENTERING_RW, PIN(7, 6), GPIO_OUTPUT) /* EC Entering RW */ -GPIO(PMIC_INT_L, PIN(6, 0), GPIO_INPUT) /* PMIC interrupt */ -GPIO(EC_RST_LTC4291_L, PIN(9, 4), GPIO_OUT_HIGH) /* PSE controller reset */ - -GPIO(POWER_RATE, PIN(7, 1), GPIO_INPUT) /* High: i3/5/7. Low: Celeron */ -GPIO(PP3300_USB_PD_EN, PIN(6, 7), GPIO_OUT_HIGH) /* Initialize PP3300_USB_PD_EN as output high */ - -GPIO(LAN_PWR_EN, PIN(8, 3), GPIO_OUT_HIGH) /* Ethernet power enabled */ - -/* I2C pins - these will be reconfigured for alternate function below */ -GPIO(I2C0_0_SCL, PIN(B, 5), GPIO_INPUT) /* EC_I2C_LTC_SCL */ -GPIO(I2C0_0_SDA, PIN(B, 4), GPIO_INPUT) /* EC_I2C_LTC_SDA */ -GPIO(I2C0_1_SCL, PIN(B, 3), GPIO_INPUT) /* EC_I2C_EEPROM_SCL */ -GPIO(I2C0_1_SDA, PIN(B, 2), GPIO_INPUT) /* EC_I2C_EEPROM_SDA */ -GPIO(I2C1_SCL, PIN(9, 0), GPIO_INPUT) /* TP184 */ -GPIO(I2C1_SDA, PIN(8, 7), GPIO_INPUT) /* TP185 */ -GPIO(I2C2_SCL, PIN(9, 2), GPIO_INPUT) /* EC_ROP_I2C_CLK */ -GPIO(I2C2_SDA, PIN(9, 1), GPIO_INPUT) /* EC_ROP_I2C_SDA */ -GPIO(I2C3_SCL, PIN(D, 1), GPIO_INPUT) /* EC_THEM_CLK */ -GPIO(I2C3_SDA, PIN(D, 0), GPIO_INPUT) /* EC_THEM_SDA */ - -/* 5V enables: INPUT=1.5A, OUT_LOW=OFF, OUT_HIGH=3A */ -GPIO(USB_C0_5V_EN, PIN(4, 2), GPIO_OUT_LOW | GPIO_PULL_UP) /* C0 5V Enable */ -GPIO(USB_C0_VBUS_ILIM, PIN(3, 5), GPIO_OUT_HIGH) -GPIO(FAN_PWR_EN, PIN(9, 5), GPIO_OUT_HIGH) /* Fan power */ -GPIO(PI3_BC12_DET_L, PIN(D, 3), GPIO_INPUT) /* USB-C */ -GPIO(USB_FP3_CHARGE_EN_L, PIN(C, 6), GPIO_OUT_LOW) /* USB-C */ -GPIO(USB_FP0_5V_EN, PIN(0, 0), GPIO_OUT_LOW) /* Front port 1 */ -GPIO(USB_FP1_5V_EN, PIN(B, 1), GPIO_OUT_LOW) /* Front port 2 */ -GPIO(USB_FP3_5V_EN, PIN(A, 1), GPIO_OUT_LOW) /* Front port 3 */ -GPIO(USB_FP_CHARGE_EN_L, PIN(A, 5), GPIO_OUT_LOW) /* USB-A */ -GPIO(PP3300_TPU_EN, PIN(0, 1), GPIO_OUT_HIGH) /* TPU 3.3V enable */ - -/* Not connected */ -GPIO(USB_C0_CHARGE_L, PIN(C, 0), GPIO_OUT_LOW) /* C0 Charge enable */ -GPIO(AC_JACK_CHARGE_L, PIN(C, 3), GPIO_OUT_LOW) /* AC jack charge enable */ -GPIO(USB_C0_PD_RST_ODL, PIN(0, 3), GPIO_OUT_LOW) /* C0 PD Reset */ -GPIO(USB_C0_TCPC_PWR, PIN(8, 4), GPIO_OUT_LOW) /* Enable C0 TCPC Power */ -GPIO(TYPE_C_65W, PIN(3, 4), GPIO_OUTPUT | GPIO_PULL_DOWN) - -/* Alternate functions GPIO definitions */ -ALTERNATE(PIN_MASK(6, 0x30), 1, MODULE_UART, 0) /* GPIO64-65 */ /* UART from EC to Servo */ -ALTERNATE(PIN_MASK(9, 0x06), 1, MODULE_I2C, 0) /* GPIO91-92 */ /* EC_I2C2_PMIC_3V3_SDA/SCL */ -ALTERNATE(PIN_MASK(A, 0x40), 1, MODULE_PWM, 0) /* GPIOA6 */ /* TACH2 */ -ALTERNATE(PIN_MASK(B, 0x30), 1, MODULE_I2C, 0) /* GPIOB4-B5 */ /* EC_I2C0_0_LTC_SDA/SCL */ -ALTERNATE(PIN_MASK(B, 0x40), 1, MODULE_PWM, 0) /* GPIOB6 */ /* EC_FAN_PWM */ -ALTERNATE(PIN_MASK(B, 0x0C), 1, MODULE_I2C, 0) /* GPOPB2-B3 */ /* EC_I2C0_1_EEPROM_SDA/SCL */ -ALTERNATE(PIN_MASK(D, 0x03), 1, MODULE_I2C, 0) /* GPIOD0-D1 */ /* EC_I2C3_SENSOR_1V8_SDA/SCL */ -/* Alternate functions for LED PWM */ -ALTERNATE(PIN_MASK(8, 0x01), 1, MODULE_PWM, 0) /* GPIO80 PWM3 Red*/ -ALTERNATE(PIN_MASK(B, 0x80), 1, MODULE_PWM, 0) /* GPOB7 PWM5 Green*/ |