diff options
Diffstat (limited to 'board/eve/board.h')
| -rw-r--r-- | board/eve/board.h | 316 |
1 files changed, 0 insertions, 316 deletions
diff --git a/board/eve/board.h b/board/eve/board.h deleted file mode 100644 index df80e4dccf..0000000000 --- a/board/eve/board.h +++ /dev/null @@ -1,316 +0,0 @@ -/* Copyright 2016 The Chromium OS Authors. All rights reserved. - * Use of this source code is governed by a BSD-style license that can be - * found in the LICENSE file. - */ - -/* Eve board configuration */ - -#ifndef __CROS_EC_BOARD_H -#define __CROS_EC_BOARD_H - -/* - * By default, enable all console messages excepted HC, ACPI and event: - * The sensor stack is generating a lot of activity. - */ -#define CC_DEFAULT (CC_ALL & ~(CC_MASK(CC_EVENTS) | CC_MASK(CC_LPC))) -#undef CONFIG_HOSTCMD_DEBUG_MODE -#define CONFIG_HOSTCMD_DEBUG_MODE HCDEBUG_OFF - -/* EC */ -#define CONFIG_ADC -#define CONFIG_BACKLIGHT_LID -#define CONFIG_BOARD_FORCE_RESET_PIN -#define CONFIG_DEVICE_EVENT -#define CONFIG_DPTF -#define CONFIG_DPTF_MULTI_PROFILE -#define CONFIG_FLASH_SIZE_BYTES 0x80000 -#define CONFIG_FPU -/* 7 day delay before hibernate */ -#undef CONFIG_HIBERNATE_DELAY_SEC -#define CONFIG_HIBERNATE_DELAY_SEC (3600 * 24 * 7) -/* 1 day delay before hibernate if battery is less than 10% */ -#define CONFIG_HIBERNATE_BATT_PCT 10 -#define CONFIG_HIBERNATE_BATT_SEC (3600 * 24) -#define CONFIG_I2C -#define CONFIG_I2C_CONTROLLER -#define CONFIG_LED_COMMON -#define CONFIG_LID_SWITCH -#define CONFIG_LOW_POWER_IDLE -#define CONFIG_LTO -#define CONFIG_CHIP_PANIC_BACKUP -#define CONFIG_SOFTWARE_PANIC -#define CONFIG_PWM -#define CONFIG_PWM_KBLIGHT -#define CONFIG_SHA256_UNROLLED -#define CONFIG_SPI_FLASH_REGS -#define CONFIG_SPI_FLASH_W25X40 -#define CONFIG_VBOOT_HASH -#define CONFIG_VOLUME_BUTTONS -#define CONFIG_VSTORE -#define CONFIG_VSTORE_SLOT_COUNT 1 -#define CONFIG_WATCHDOG_HELP -#define CONFIG_WIRELESS -#define CONFIG_WIRELESS_SUSPEND \ - (EC_WIRELESS_SWITCH_WLAN | EC_WIRELESS_SWITCH_WLAN_POWER) -#define WIRELESS_GPIO_WLAN GPIO_WLAN_OFF_L -#define WIRELESS_GPIO_WLAN_POWER GPIO_PP3300_DX_WLAN -#undef CONFIG_UART_TX_BUF_SIZE -#define CONFIG_UART_TX_BUF_SIZE 256 - -/* EC console commands */ -#define CONFIG_CMD_ACCELS -#define CONFIG_CMD_ACCEL_INFO -#define CONFIG_CMD_BATT_MFG_ACCESS -#define CONFIG_CMD_CHARGER_ADC_AMON_BMON -#define CONFIG_HOSTCMD_PD_CONTROL - -/* EC console history configuration */ -#undef CONFIG_CONSOLE_HISTORY -#define CONFIG_CONSOLE_HISTORY 1 - -/* SOC */ -#define CONFIG_CHIPSET_SKYLAKE -#define CONFIG_CHIPSET_HAS_PLATFORM_PMIC_RESET -#define CONFIG_CHIPSET_RESET_HOOK -#define CONFIG_HOSTCMD_ESPI -#define CONFIG_HOSTCMD_ESPI_VW_SLP_S3 -#define CONFIG_HOSTCMD_ESPI_VW_SLP_S4 - -#define CONFIG_KEYBOARD_COL2_INVERTED -#undef CONFIG_KEYBOARD_VIVALDI -#define CONFIG_KEYBOARD_PROTOCOL_8042 -#define CONFIG_KEYBOARD_REFRESH_ROW3 -#define CONFIG_TABLET_MODE - -/* Battery */ -#define CONFIG_BATTERY_CRITICAL_SHUTDOWN_CUT_OFF -#define CONFIG_BATTERY_CUT_OFF -#define CONFIG_BATTERY_DEVICE_CHEMISTRY "LION" -#define CONFIG_BATTERY_LEVEL_NEAR_FULL 94 -#define CONFIG_BATTERY_PRESENT_CUSTOM -#define CONFIG_BATTERY_HW_PRESENT_CUSTOM -#define CONFIG_BATTERY_SMART -#define CONFIG_BATTERY_VENDOR_PARAM - -/* Charger */ -#define CONFIG_CHARGE_MANAGER -#define CONFIG_CHARGE_MANAGER_EXTERNAL_POWER_LIMIT -#define CONFIG_CHARGE_RAMP_SW -#define CONFIG_CHARGER -#define CONFIG_CHARGER_BD9995X -#define CONFIG_CHARGER_BD9995X_CHGEN -#define CONFIG_CHARGER_DISCHARGE_ON_AC -#define CONFIG_CHARGER_INPUT_CURRENT 512 -#define CONFIG_CHARGER_MAINTAIN_VBAT -#define CONFIG_CHARGER_PROFILE_OVERRIDE -#define CONFIG_CHARGER_PSYS_READ -#define CONFIG_CHARGER_SENSE_RESISTOR 10 -#define CONFIG_CHARGER_SENSE_RESISTOR_AC 10 -#define BD9995X_IOUT_GAIN_SELECT \ - BD9995X_CMD_PMON_IOUT_CTRL_SET_IOUT_GAIN_SET_20V -#define BD9995X_PSYS_GAIN_SELECT \ - BD9995X_CMD_PMON_IOUT_CTRL_SET_PMON_GAIN_SET_02UAW -#define CONFIG_EXTPOWER_GPIO -#undef CONFIG_EXTPOWER_DEBOUNCE_MS -#define CONFIG_EXTPOWER_DEBOUNCE_MS 1000 -#define CONFIG_POWER_BUTTON -#define CONFIG_POWER_BUTTON_X86 -#define CONFIG_POWER_COMMON -#define CONFIG_POWER_SIGNAL_INTERRUPT_STORM_DETECT_THRESHOLD 30 -#define CONFIG_PWR_STATE_DISCHARGE_FULL - -/* Sensor */ -#define CONFIG_MKBP_EVENT -/* Don't wake up from suspend on any MKBP event. */ -#define CONFIG_MKBP_EVENT_WAKEUP_MASK 0 -#define CONFIG_MKBP_USE_HOST_EVENT -#define CONFIG_ACCEL_KXCJ9 -#define CONFIG_ALS_SI114X 0x40 -#define CONFIG_ALS_SI114X_INT_EVENT \ - TASK_EVENT_MOTION_SENSOR_INTERRUPT(LID_LIGHT) -#define CONFIG_ALS_SI114X_POLLING -#define CONFIG_TEMP_SENSOR -#define CONFIG_TEMP_SENSOR_BD99992GW -#define CONFIG_THERMISTOR_NCP15WB -#define CONFIG_ACCELGYRO_BMI160 -#define CONFIG_MAG_BMI_BMM150 -#define CONFIG_ACCEL_INTERRUPTS -#define CONFIG_ACCELGYRO_BMI160_INT_EVENT \ - TASK_EVENT_MOTION_SENSOR_INTERRUPT(BASE_ACCEL) -#define CONFIG_ACCELGYRO_SEC_ADDR_FLAGS BMM150_ADDR0_FLAGS -#define CONFIG_ACCELGYRO_BMI160_INT2_OUTPUT /* Unused */ -#define CONFIG_MAG_CALIBRATE -#define CONFIG_LID_ANGLE -#define CONFIG_LID_ANGLE_INVALID_CHECK -#define CONFIG_LID_ANGLE_TABLET_MODE -#define CONFIG_LID_ANGLE_UPDATE -#define CONFIG_LID_ANGLE_SENSOR_BASE BASE_ACCEL -#define CONFIG_LID_ANGLE_SENSOR_LID LID_ACCEL - -/* Enable sensor fifo, must also define the _SIZE and _THRES */ -#define CONFIG_ACCEL_FIFO -/* FIFO size is in power of 2. */ -#define CONFIG_ACCEL_FIFO_SIZE 256 -/* Depends on how fast the AP boots and typical ODRs */ -#define CONFIG_ACCEL_FIFO_THRES (CONFIG_ACCEL_FIFO_SIZE / 3) - -/* Enable double tap detection */ -#define CONFIG_GESTURE_DETECTION -#define CONFIG_GESTURE_HOST_DETECTION -#define CONFIG_GESTURE_SENSOR_DOUBLE_TAP -#define CONFIG_GESTURE_SAMPLING_INTERVAL_MS 5 -#define CONFIG_GESTURE_TAP_THRES_MG 100 -#define CONFIG_GESTURE_TAP_MAX_INTERSTICE_T 500 -#define CONFIG_GESTURE_DETECTION_MASK BIT(CONFIG_GESTURE_TAP_SENSOR) -#define CONFIG_GESTURE_TAP_SENSOR 1 - -/* USB */ -#define CONFIG_USB_PID 0x504B - -#define CONFIG_USB_CHARGER -#define CONFIG_USB_DRP_ACC_TRYSRC -#define CONFIG_USB_PD_ALT_MODE -#define CONFIG_USB_PD_ALT_MODE_DFP -#define CONFIG_USB_PD_COMM_LOCKED -#define CONFIG_USB_PD_DECODE_SOP -#define CONFIG_USB_PD_DISCHARGE_TCPC -#define CONFIG_USB_PD_DUAL_ROLE -#define CONFIG_USB_PD_DUAL_ROLE_AUTO_TOGGLE -#define CONFIG_BD9995X_DELAY_INPUT_PORT_SELECT -#define CONFIG_USB_PD_LOGGING -#define CONFIG_USB_PD_PORT_MAX_COUNT 2 -#define CONFIG_USB_PD_VBUS_DETECT_CHARGER -#define CONFIG_USB_PD_TCPC_BOARD_INIT -#define CONFIG_USB_PD_TCPC_LOW_POWER -#define CONFIG_USB_PD_TCPM_MUX -#define CONFIG_USB_PD_TCPM_ANX3429 -#define CONFIG_USB_PD_TCPM_TCPCI -#define CONFIG_USB_PD_TRY_SRC -#undef CONFIG_USB_PD_TRY_SRC_MIN_BATT_SOC -#define CONFIG_USB_PD_TRY_SRC_MIN_BATT_SOC 2 -#define CONFIG_USB_POWER_DELIVERY -#define CONFIG_USB_PD_TCPMV2 -#define CONFIG_USBC_SS_MUX -#define CONFIG_USBC_VCONN -#define CONFIG_USBC_VCONN_SWAP - -/* Optional feature to configure npcx chip */ -#define NPCX_UART_MODULE2 1 /* 1:GPIO64/65 as UART */ -#define NPCX_JTAG_MODULE2 0 /* 0:GPIO21/17/16/20 as JTAG */ -#define NPCX_TACH_SEL2 0 /* 0:GPIO40/73 as TACH */ - -/* I2C ports */ -#define I2C_PORT_TCPC0 NPCX_I2C_PORT0_0 -#define I2C_PORT_TCPC1 NPCX_I2C_PORT0_1 -#define I2C_PORT_GYRO NPCX_I2C_PORT1 -#define I2C_PORT_ACCEL I2C_PORT_GYRO -#define I2C_PORT_LID_ACCEL NPCX_I2C_PORT2 -#define I2C_PORT_ALS NPCX_I2C_PORT2 -#define I2C_PORT_PMIC NPCX_I2C_PORT3 -#define I2C_PORT_BATTERY NPCX_I2C_PORT3 -#define I2C_PORT_CHARGER NPCX_I2C_PORT3 -#define I2C_PORT_THERMAL I2C_PORT_PMIC -#define I2C_PORT_MP2949 NPCX_I2C_PORT3 - -/* I2C addresses */ -#define I2C_ADDR_BD99992_FLAGS 0x30 -#define I2C_ADDR_MP2949_FLAGS 0x20 - -#ifndef __ASSEMBLER__ - -#include "gpio_signal.h" -#include "registers.h" - -enum board_version_list { - BOARD_VERSION_P0, - BOARD_VERSION_P0B, - BOARD_VERSION_P1, - BOARD_VERSION_P1B, - BOARD_VERSION_EVT, - BOARD_VERSION_EVTB, - BOARD_VERSION_DVT, - BOARD_VERSION_DVTB, - BOARD_VERSION_PVT, -}; - -enum temp_sensor_id { - TEMP_SENSOR_BATTERY, /* BD99956GW TSENSE */ - TEMP_SENSOR_AMBIENT, /* BD99992GW SYSTHERM0 */ - TEMP_SENSOR_CHARGER, /* BD99992GW SYSTHERM1 */ - TEMP_SENSOR_DRAM, /* BD99992GW SYSTHERM2 */ - TEMP_SENSOR_EMMC, /* BD99992GW SYSTHERM3 */ - TEMP_SENSOR_GYRO, - TEMP_SENSOR_COUNT -}; - -/* - * The PWM channel enums for the LEDs need to be in Red, Green, Blue order as - * the 'set_color()' function assumes this order. The left vs right order - * doesn't matter as long as each side follows RGB order. - */ -enum pwm_channel { - PWM_CH_KBLIGHT, - PWM_CH_LED_L_RED, - PWM_CH_LED_L_GREEN, - PWM_CH_LED_L_BLUE, - PWM_CH_LED_R_RED, - PWM_CH_LED_R_GREEN, - PWM_CH_LED_R_BLUE, - PWM_CH_COUNT -}; - -/* - * For backward compatibility, to report ALS via ACPI, - * Define the number of ALS sensors: motion_sensor copy the data to the ALS - * memmap region. - */ -#define CONFIG_ALS -#define ALS_COUNT 1 - -/* - * Motion sensors: - * When reading through IO memory is set up for sensors (LPC is used), - * the first 2 entries must be accelerometers, then gyroscope. - * For BMI160, accel, gyro and compass sensors must be next to each other. - */ -enum sensor_id { - LID_ACCEL = 0, - BASE_ACCEL, - BASE_GYRO, - BASE_MAG, - LID_LIGHT, - SENSOR_COUNT, -}; - -enum adc_channel { - ADC_CH_COUNT -}; - -/* - * delay to turn on the power supply max is ~16ms. - * delay to turn off the power supply max is about ~180ms. - */ -#define PD_POWER_SUPPLY_TURN_ON_DELAY 30000 /* us */ -#define PD_POWER_SUPPLY_TURN_OFF_DELAY 250000 /* us */ - -/* delay to turn on/off vconn */ - -/* Define typical operating power and max power */ -#define PD_OPERATING_POWER_MW 15000 -#define PD_MAX_POWER_MW 45000 -#define PD_MAX_CURRENT_MA 3000 -#define PD_MAX_VOLTAGE_MV 20000 - -/* Board specific handlers */ -int board_get_version(void); -void board_reset_pd_mcu(void); -void board_set_tcpc_power_mode(int port, int mode); -void board_tcpc_init(void); -void led_register_double_tap(void); - -/* Sensors without hardware FIFO are in forced mode */ -#define CONFIG_ACCEL_FORCE_MODE_MASK (BIT(LID_ACCEL) | BIT(LID_LIGHT)) - -#endif /* !__ASSEMBLER__ */ - -#endif /* __CROS_EC_BOARD_H */ |