diff options
Diffstat (limited to 'board/fizz/gpio.inc')
| -rw-r--r-- | board/fizz/gpio.inc | 114 |
1 files changed, 0 insertions, 114 deletions
diff --git a/board/fizz/gpio.inc b/board/fizz/gpio.inc deleted file mode 100644 index 7da0bfce71..0000000000 --- a/board/fizz/gpio.inc +++ /dev/null @@ -1,114 +0,0 @@ -/* -*- mode:c -*- - * - * Copyright 2017 The Chromium OS Authors. All rights reserved. - * Use of this source code is governed by a BSD-style license that can be - * found in the LICENSE file. - */ - -/* Declare symbolic names for all the GPIOs that we care about. - * Note: Those with interrupt handlers must be declared first. */ - -GPIO_INT(USB_C0_PD_INT_ODL, PIN(3, 7), GPIO_INT_FALLING | GPIO_PULL_UP, tcpc_alert_event) -GPIO_INT(AC_PRESENT, PIN(C, 1), GPIO_INT_BOTH, extpower_interrupt) -GPIO_INT(POWER_BUTTON_L, PIN(0, 4), GPIO_INT_BOTH | GPIO_PULL_UP, power_button_interrupt) /* MECH_PWR_BTN_ODL */ - -GPIO_INT(PCH_SLP_S0_L, PIN(7, 5), GPIO_INT_BOTH, power_signal_interrupt) -#ifndef CONFIG_HOSTCMD_ESPI_VW_SLP_S3 -GPIO_INT(PCH_SLP_S3_L, PIN(7, 3), GPIO_INT_BOTH, power_signal_interrupt) -#endif -#ifndef CONFIG_HOSTCMD_ESPI_VW_SLP_S4 -GPIO_INT(PCH_SLP_S4_L, PIN(8, 6), GPIO_INT_BOTH, power_signal_interrupt) -#endif -GPIO_INT(PCH_SLP_SUS_L, PIN(6, 2), GPIO_INT_BOTH, power_signal_interrupt) -GPIO_INT(RSMRST_L_PGOOD, PIN(B, 0), GPIO_INT_BOTH, power_signal_interrupt) -GPIO_INT(PMIC_DPWROK, PIN(C, 7), GPIO_INT_BOTH, power_signal_interrupt) -GPIO_INT(WP_L, PIN(9, 3), GPIO_INT_BOTH, switch_interrupt) -GPIO_INT(ADP_IN_L, PIN(C, 5), GPIO_INT_BOTH | GPIO_PULL_UP, adp_in) /* Low: BJ detected */ -GPIO_INT(USB_C0_VBUS_WAKE_L, PIN(9, 7), GPIO_INT_BOTH | GPIO_PULL_UP, vbus0_evt) -GPIO_INT(RECOVERY_L, PIN(8, 2), GPIO_INT_BOTH, button_interrupt) /* Recovery button */ -GPIO(PCH_RTCRST, PIN(E, 7), GPIO_OUT_LOW) /* RTCRST# to SOC */ -GPIO(WLAN_OFF_L, PIN(7, 2), GPIO_OUT_LOW) /* Disable WLAN */ -GPIO(PP3300_DX_WLAN, PIN(A, 7), GPIO_OUT_LOW) /* Enable WLAN 3.3V Power */ -GPIO(CPU_PROCHOT, PIN(8, 1), GPIO_OUT_HIGH) /* PROCHOT# to SOC */ -GPIO(PCH_ACPRESENT, PIN(5, 0), GPIO_ODR_LOW) /* ACOK to SOC */ -GPIO(PCH_WAKE_L, PIN(A, 3), GPIO_ODR_HIGH) /* Wake SOC */ -GPIO(PCH_RSMRST_L, PIN(7, 0), GPIO_OUT_LOW) /* RSMRST# to SOC */ -GPIO(PCH_PWRBTN_L, PIN(7, 4), GPIO_ODR_HIGH) /* Power Button to SOC */ -GPIO(EC_PLATFORM_RST, PIN(4, 5), GPIO_OUT_LOW) /* EC Reset to LDO_EN */ -GPIO(SYS_RESET_L, PIN(6, 1), GPIO_ODR_HIGH) /* Cold Reset to SOC */ -GPIO(PMIC_SLP_SUS_L, PIN(8, 5), GPIO_OUT_LOW) /* SLP_SUS# to PMIC */ -GPIO(CCD_MODE_ODL, PIN(6, 3), GPIO_INPUT) /* Case Closed Debug Mode */ -GPIO(EC_HAVEN_RESET_ODL, PIN(0, 2), GPIO_ODR_HIGH) /* H1 Reset */ -GPIO(ENTERING_RW, PIN(7, 6), GPIO_OUTPUT) /* EC Entering RW */ -GPIO(PMIC_INT_L, PIN(6, 0), GPIO_INPUT) /* PMIC interrupt */ -GPIO(TYPE_C_60W, PIN(3, 3), GPIO_OUTPUT | GPIO_PULL_DOWN) -GPIO(TYPE_C_65W, PIN(3, 4), GPIO_OUTPUT | GPIO_PULL_DOWN) -GPIO(TYPE_C_87W, PIN(4, 4), GPIO_OUTPUT | GPIO_PULL_DOWN) -GPIO(POWER_RATE, PIN(7, 1), GPIO_INPUT) /* High: i3/5/7. Low: Celeron */ - -/* Fizz specific pins */ -GPIO(LAN_PWR_EN, PIN(8, 3), GPIO_OUT_HIGH) /* Ethernet power enabled */ - -GPIO(PP5000_DX_NFC, PIN(1, 5), GPIO_OUTPUT) - -GPIO(PP3300_DX_CAM, PIN(1, 0), GPIO_OUT_HIGH) -GPIO(CAM_PMIC_RST_L, PIN(0, 7), GPIO_INPUT) - -GPIO(WLAN_PE_RST, PIN(1, 2), GPIO_OUTPUT) -GPIO(PP3300_DX_LTE, PIN(0, 5), GPIO_OUT_LOW) -GPIO(PP3300_DX_BASE, PIN(1, 1), GPIO_OUT_LOW) - -/* I2C pins - these will be reconfigured for alternate function below */ -GPIO(I2C0_0_SCL, PIN(B, 5), GPIO_INPUT) /* EC_I2C_USB_C0_PD_SCL */ -GPIO(I2C0_0_SDA, PIN(B, 4), GPIO_INPUT) /* EC_I2C_USB_C0_PD_SDA */ -GPIO(I2C0_1_SCL, PIN(B, 3), GPIO_INPUT) /* EC_I2C_EEPROM_SCL */ -GPIO(I2C0_1_SDA, PIN(B, 2), GPIO_INPUT) /* EC_I2C_EEPROM_SDA */ -GPIO(I2C1_SCL, PIN(9, 0), GPIO_INPUT) /* EC_I2C_BAT_SCL */ -GPIO(I2C1_SDA, PIN(8, 7), GPIO_INPUT) /* EC_I2C_BAT_SDA */ -GPIO(I2C2_SCL, PIN(9, 2), GPIO_INPUT) /* EC_ROP_I2C_CLK */ -GPIO(I2C2_SDA, PIN(9, 1), GPIO_INPUT) /* EC_ROP_I2C_SDA */ -GPIO(I2C3_SCL, PIN(D, 1), GPIO_INPUT) /* EC_THEM_CLK */ -GPIO(I2C3_SDA, PIN(D, 0), GPIO_INPUT) /* EC_THEM_SDA */ - -/* 5V enables: INPUT=1.5A, OUT_LOW=OFF, OUT_HIGH=3A */ -GPIO(USB_C0_5V_EN, PIN(4, 2), GPIO_OUT_LOW | GPIO_PULL_UP) /* C0 5V Enable */ -GPIO(USB_C0_CHARGE_L, PIN(C, 0), GPIO_OUT_LOW) /* C0 Charge enable */ -GPIO(AC_JACK_CHARGE_L, PIN(C, 3), GPIO_OUT_LOW) /* AC jack charge enable */ -GPIO(USB_C0_PD_RST_ODL, PIN(0, 3), GPIO_OUT_LOW) /* C0 PD Reset */ -GPIO(USB_C0_DP_HPD, PIN(9, 4), GPIO_INPUT) /* C0 DP Hotplug Detect */ -GPIO(USB_C0_TCPC_PWR, PIN(8, 4), GPIO_OUT_LOW) /* Enable C0 TCPC Power */ -GPIO(FAN_PWR_EN, PIN(9, 5), GPIO_OUT_HIGH) /* Fan power */ -GPIO(USB1_ENABLE, PIN(3, 2), GPIO_OUT_LOW) /* Rear port, bottom */ -GPIO(USB2_ENABLE, PIN(C, 6), GPIO_OUT_LOW) /* Rear port, top */ -GPIO(USB3_ENABLE, PIN(A, 1), GPIO_OUT_LOW) /* Rear port, single */ -GPIO(USB4_ENABLE, PIN(0, 0), GPIO_OUT_LOW) /* Front port 1 */ -GPIO(USB5_ENABLE, PIN(B, 1), GPIO_OUT_LOW) /* Front port 2 */ -GPIO(USB_A_CHARGE_EN_L, PIN(A, 5), GPIO_OUT_LOW) - -GPIO(CEC_OUT, PIN(3, 6), GPIO_OUT_HIGH | GPIO_OPEN_DRAIN) -GPIO(CEC_IN, PIN(4, 0), GPIO_INPUT) -GPIO(CEC_PULL_UP, PIN(D, 3), GPIO_OUT_HIGH) - -/* Board ID */ -GPIO(BOARD_VERSION1, PIN(C, 4), GPIO_INPUT) /* Board ID bit0 */ -GPIO(BOARD_VERSION2, PIN(C, 2), GPIO_INPUT) /* Board ID bit1 */ -GPIO(BOARD_VERSION3, PIN(0, 1), GPIO_INPUT) /* Board ID bit2 */ - -/* Test points */ -GPIO(TP248, PIN(5, 7), GPIO_INPUT | GPIO_PULL_UP) /* EC_GPIO57 */ -GPIO(TP249, PIN(6, 6), GPIO_INPUT | GPIO_PULL_UP) /* EC_GPO66_ARM_L */ -GPIO(TP250, PIN(3, 5), GPIO_INPUT | GPIO_PULL_UP) /* EC_GPIO35_TEST_L */ - -/* Alternate functions GPIO definitions */ -ALTERNATE(PIN_MASK(6, 0x30), 1, MODULE_UART, 0) /* GPIO64-65 */ /* UART from EC to Servo */ -ALTERNATE(PIN_MASK(8, 0x80), 1, MODULE_I2C, 0) /* GPIO87 */ /* EC_I2C1_3V3_SDA */ -ALTERNATE(PIN_MASK(9, 0x01), 1, MODULE_I2C, 0) /* GPIO90 */ /* EC_I2C1_3V3_SCL */ -ALTERNATE(PIN_MASK(9, 0x06), 1, MODULE_I2C, 0) /* GPIO91-92 */ /* EC_I2C2_PMIC_3V3_SDA/SCL */ -ALTERNATE(PIN_MASK(A, 0x40), 1, MODULE_PWM, 0) /* GPIOA6 */ /* TACH2 */ -ALTERNATE(PIN_MASK(B, 0x30), 1, MODULE_I2C, 0) /* GPIOB4-B5 */ /* EC_I2C0_0_USBC_3V3_SDA/SCL */ -ALTERNATE(PIN_MASK(B, 0x40), 1, MODULE_PWM, 0) /* GPIOB6 */ /* EC_FAN_PWM */ -ALTERNATE(PIN_MASK(B, 0x0C), 1, MODULE_I2C, 0) /* GPOPB2-B3 */ /* EC_I2C0_1_3V3_SDA/SCL */ -ALTERNATE(PIN_MASK(D, 0x03), 1, MODULE_I2C, 0) /* GPIOD0-D1 */ /* EC_I2C3_SENSOR_1V8_SDA/SCL */ -/* Alternate functions for LED PWM */ -ALTERNATE(PIN_MASK(8, 0x01), 1, MODULE_PWM, 0) /* GPIO80 PWM3 Red*/ -ALTERNATE(PIN_MASK(B, 0x80), 1, MODULE_PWM, 0) /* GPOB7 PWM5 Green*/ |