diff options
Diffstat (limited to 'board/fleex/board.c')
| -rw-r--r-- | board/fleex/board.c | 333 |
1 files changed, 0 insertions, 333 deletions
diff --git a/board/fleex/board.c b/board/fleex/board.c deleted file mode 100644 index 7e11d671c6..0000000000 --- a/board/fleex/board.c +++ /dev/null @@ -1,333 +0,0 @@ -/* Copyright 2018 The Chromium OS Authors. All rights reserved. - * Use of this source code is governed by a BSD-style license that can be - * found in the LICENSE file. - */ - -/* Fleex board-specific configuration */ - -#include "adc.h" -#include "battery.h" -#include "button.h" -#include "charge_manager.h" -#include "charge_state.h" -#include "common.h" -#include "console.h" -#include "cros_board_info.h" -#include "driver/accel_lis2dh.h" -#include "driver/accelgyro_lsm6dsm.h" -#include "driver/charger/isl923x.h" -#include "driver/ppc/nx20p348x.h" -#include "driver/ppc/syv682x.h" -#include "driver/tcpm/anx7447.h" -#include "driver/tcpm/ps8xxx.h" -#include "driver/tcpm/tcpci.h" -#include "driver/tcpm/tcpm.h" -#include "extpower.h" -#include "gpio.h" -#include "hooks.h" -#include "i2c.h" -#include "keyboard_scan.h" -#include "lid_switch.h" -#include "motion_sense.h" -#include "power.h" -#include "power_button.h" -#include "switch.h" -#include "system.h" -#include "task.h" -#include "tablet_mode.h" -#include "tcpm/tcpci.h" -#include "temp_sensor.h" -#include "temp_sensor/thermistor.h" -#include "usb_mux.h" -#include "usbc_ppc.h" -#include "util.h" - -#define CPRINTSUSB(format, args...) cprints(CC_USBCHARGE, format, ## args) -#define CPRINTFUSB(format, args...) cprintf(CC_USBCHARGE, format, ## args) - -#define USB_PD_PORT_ANX7447 0 -#define USB_PD_PORT_PS8751 1 - -static uint8_t sku_id; -static int is_support_syv_ppc; - -const struct ppc_config_t ppc_syv682x_port0 = { - .i2c_port = I2C_PORT_TCPC0, - .i2c_addr_flags = SYV682X_ADDR0_FLAGS, - .drv = &syv682x_drv, -}; - -const struct ppc_config_t ppc_syv682x_port1 = { - .i2c_port = I2C_PORT_TCPC1, - .i2c_addr_flags = SYV682X_ADDR0_FLAGS, - .drv = &syv682x_drv, -}; - -/* Check PPC_ID pin status to decide which one ppc is used. */ -static int board_is_syv_ppc(void) -{ - return gpio_get_level(GPIO_PPC_ID); -} - -static void board_update_ppc_config_from_board(void) -{ - if (!is_support_syv_ppc) - return; - - memcpy(&ppc_chips[USB_PD_PORT_TCPC_0], - &ppc_syv682x_port0, - sizeof(struct ppc_config_t)); - memcpy(&ppc_chips[USB_PD_PORT_TCPC_1], - &ppc_syv682x_port1, - sizeof(struct ppc_config_t)); - - gpio_set_flags(GPIO_USB_PD_C0_INT_ODL, GPIO_INT_BOTH); - gpio_set_flags(GPIO_USB_PD_C1_INT_ODL, GPIO_INT_BOTH); -} - -static void ppc_interrupt(enum gpio_signal signal) -{ - switch (signal) { - case GPIO_USB_PD_C0_INT_ODL: - if (is_support_syv_ppc) - syv682x_interrupt(0); - else - nx20p348x_interrupt(0); - break; - - case GPIO_USB_PD_C1_INT_ODL: - if (is_support_syv_ppc) - syv682x_interrupt(1); - else - nx20p348x_interrupt(1); - break; - - default: - break; - } -} - -/* Must come after other header files and GPIO interrupts*/ -#include "gpio_list.h" - -/* ADC channels */ -const struct adc_t adc_channels[] = { - [ADC_TEMP_SENSOR_AMB] = { - "TEMP_AMB", NPCX_ADC_CH0, ADC_MAX_VOLT, ADC_READ_MAX+1, 0}, - [ADC_TEMP_SENSOR_CHARGER] = { - "TEMP_CHARGER", NPCX_ADC_CH1, ADC_MAX_VOLT, ADC_READ_MAX+1, 0}, - [ADC_VBUS_C0] = {"VBUS_C0", NPCX_ADC_CH9, ADC_MAX_VOLT*10, ADC_READ_MAX+1, 0}, - [ADC_VBUS_C1] = {"VBUS_C1", NPCX_ADC_CH4, ADC_MAX_VOLT*10, ADC_READ_MAX+1, 0}, -}; -BUILD_ASSERT(ARRAY_SIZE(adc_channels) == ADC_CH_COUNT); - -const struct temp_sensor_t temp_sensors[] = { - [TEMP_SENSOR_BATTERY] = {.name = "Battery", - .type = TEMP_SENSOR_TYPE_BATTERY, - .read = charge_get_battery_temp, - .idx = 0}, - [TEMP_SENSOR_AMBIENT] = {.name = "Ambient", - .type = TEMP_SENSOR_TYPE_BOARD, - .read = get_temp_3v3_51k1_47k_4050b, - .idx = ADC_TEMP_SENSOR_AMB}, - [TEMP_SENSOR_CHARGER] = {.name = "Charger", - .type = TEMP_SENSOR_TYPE_BOARD, - .read = get_temp_3v3_13k7_47k_4050b, - .idx = ADC_TEMP_SENSOR_CHARGER}, -}; -BUILD_ASSERT(ARRAY_SIZE(temp_sensors) == TEMP_SENSOR_COUNT); - -/* Motion sensors */ -/* Mutexes */ -static struct mutex g_lid_mutex; -static struct mutex g_base_mutex; - -/* Matrix to rotate accelerometer into standard reference frame */ -const mat33_fp_t lid_standard_ref = { - { 0, FLOAT_TO_FP(1), 0}, - { FLOAT_TO_FP(-1), 0, 0}, - { 0, 0, FLOAT_TO_FP(1)} -}; - - const mat33_fp_t base_standard_ref = { - { FLOAT_TO_FP(-1), 0, 0}, - { 0, FLOAT_TO_FP(-1), 0}, - { 0, 0, FLOAT_TO_FP(1)} - }; - -/* sensor private data */ -static struct stprivate_data g_lis2dh_data; -static struct lsm6dsm_data lsm6dsm_data = LSM6DSM_DATA; - -/* Drivers */ -struct motion_sensor_t motion_sensors[] = { - [LID_ACCEL] = { - .name = "Lid Accel", - .active_mask = SENSOR_ACTIVE_S0_S3, - .chip = MOTIONSENSE_CHIP_LIS2DE, - .type = MOTIONSENSE_TYPE_ACCEL, - .location = MOTIONSENSE_LOC_LID, - .drv = &lis2dh_drv, - .mutex = &g_lid_mutex, - .drv_data = &g_lis2dh_data, - .port = I2C_PORT_SENSOR, - .i2c_spi_addr_flags = LIS2DH_ADDR1_FLAGS, - .rot_standard_ref = &lid_standard_ref, - .default_range = 2, /* g */ - /* We only use 2g because its resolution is only 8-bits */ - .min_frequency = LIS2DH_ODR_MIN_VAL, - .max_frequency = LIS2DH_ODR_MAX_VAL, - .config = { - /* EC use accel for angle detection */ - [SENSOR_CONFIG_EC_S0] = { - .odr = 10000 | ROUND_UP_FLAG, - }, - /* Sensor on for lid angle detection */ - [SENSOR_CONFIG_EC_S3] = { - .odr = 10000 | ROUND_UP_FLAG, - }, - }, - }, - - [BASE_ACCEL] = { - .name = "Base Accel", - .active_mask = SENSOR_ACTIVE_S0_S3, - .chip = MOTIONSENSE_CHIP_LSM6DSM, - .type = MOTIONSENSE_TYPE_ACCEL, - .location = MOTIONSENSE_LOC_BASE, - .drv = &lsm6dsm_drv, - .mutex = &g_base_mutex, - .drv_data = LSM6DSM_ST_DATA(lsm6dsm_data, - MOTIONSENSE_TYPE_ACCEL), - .int_signal = GPIO_BASE_SIXAXIS_INT_L, - .flags = MOTIONSENSE_FLAG_INT_SIGNAL, - .port = I2C_PORT_SENSOR, - .i2c_spi_addr_flags = LSM6DSM_ADDR0_FLAGS, - .rot_standard_ref = &base_standard_ref, - .default_range = 4, /* g, to meet CDD 7.3.1/C-1-4 reqs */ - .min_frequency = LSM6DSM_ODR_MIN_VAL, - .max_frequency = LSM6DSM_ODR_MAX_VAL, - .config = { - /* EC use accel for angle detection */ - [SENSOR_CONFIG_EC_S0] = { - .odr = 13000 | ROUND_UP_FLAG, - .ec_rate = 100 * MSEC, - }, - /* Sensor on for angle detection */ - [SENSOR_CONFIG_EC_S3] = { - .odr = 10000 | ROUND_UP_FLAG, - .ec_rate = 100 * MSEC, - }, - }, - }, - - [BASE_GYRO] = { - .name = "Base Gyro", - .active_mask = SENSOR_ACTIVE_S0_S3, - .chip = MOTIONSENSE_CHIP_LSM6DSM, - .type = MOTIONSENSE_TYPE_GYRO, - .location = MOTIONSENSE_LOC_BASE, - .drv = &lsm6dsm_drv, - .mutex = &g_base_mutex, - .drv_data = LSM6DSM_ST_DATA(lsm6dsm_data, - MOTIONSENSE_TYPE_GYRO), - .int_signal = GPIO_BASE_SIXAXIS_INT_L, - .flags = MOTIONSENSE_FLAG_INT_SIGNAL, - .port = I2C_PORT_SENSOR, - .i2c_spi_addr_flags = LSM6DSM_ADDR0_FLAGS, - .default_range = 1000 | ROUND_UP_FLAG, /* dps */ - .rot_standard_ref = &base_standard_ref, - .min_frequency = LSM6DSM_ODR_MIN_VAL, - .max_frequency = LSM6DSM_ODR_MAX_VAL, - }, -}; - -unsigned int motion_sensor_count = ARRAY_SIZE(motion_sensors); - -static int board_is_convertible(void) -{ - return sku_id == 0x21 || sku_id == 0x22 || sku_id == 0x23 - || sku_id == 0xff; -} - -static void board_update_sensor_config_from_sku(void) -{ - if (board_is_convertible()) { - motion_sensor_count = ARRAY_SIZE(motion_sensors); - /* Enable Base Accel interrupt */ - gpio_enable_interrupt(GPIO_BASE_SIXAXIS_INT_L); - } else { - motion_sensor_count = 0; - gmr_tablet_switch_disable(); - /* Base accel is not stuffed, don't allow line to float */ - gpio_set_flags(GPIO_BASE_SIXAXIS_INT_L, - GPIO_INPUT | GPIO_PULL_DOWN); - } -} - -static void cbi_init(void) -{ - uint32_t val; - - if (cbi_get_sku_id(&val) == EC_SUCCESS) - sku_id = val; - ccprints("SKU: 0x%04x", sku_id); - - board_update_sensor_config_from_sku(); -} -DECLARE_HOOK(HOOK_INIT, cbi_init, HOOK_PRIO_INIT_I2C + 1); - -/* This callback disables keyboard when convertibles are fully open */ -__override void lid_angle_peripheral_enable(int enable) -{ - /* - * If the lid is in tablet position via other sensors, - * ignore the lid angle, which might be faulty then - * disable keyboard. - */ - if (tablet_get_mode()) - enable = 0; - if (board_is_convertible()) - keyboard_scan_enable(enable, KB_SCAN_DISABLE_LID_ANGLE); -} - -void board_overcurrent_event(int port, int is_overcurrented) -{ - /* Check that port number is valid. */ - if ((port < 0) || (port >= CONFIG_USB_PD_PORT_MAX_COUNT)) - return; - - /* Note that the level is inverted because the pin is active low. */ - gpio_set_level(GPIO_USB_C_OC, !is_overcurrented); -} - -static void charger_set_buck_boost_mode(void) -{ - int reg; - /* Reduce Buck-boost mode switching frequency to improve power efficiency. */ - if (i2c_read16(I2C_PORT_CHARGER, I2C_ADDR_CHARGER_FLAGS, - ISL9238_REG_CONTROL3, ®) == EC_SUCCESS) { - reg |= ISL9238_C3_BB_SWITCHING_PERIOD; - if (i2c_write16(I2C_PORT_CHARGER, I2C_ADDR_CHARGER_FLAGS, - ISL9238_REG_CONTROL3, reg)) - ccprints("Failed to set isl9238"); - } -} - -static void board_init(void) -{ - charger_set_buck_boost_mode(); - - is_support_syv_ppc = board_is_syv_ppc(); - - board_update_ppc_config_from_board(); -} -DECLARE_HOOK(HOOK_INIT, board_init, HOOK_PRIO_DEFAULT); - -int ppc_get_alert_status(int port) -{ - if (port == 0) - return gpio_get_level(GPIO_USB_PD_C0_INT_ODL) == 0; - - return gpio_get_level(GPIO_USB_PD_C1_INT_ODL) == 0; -} |