diff options
Diffstat (limited to 'board/garg')
| -rw-r--r-- | board/garg/battery.c | 124 | ||||
| -rw-r--r-- | board/garg/board.c | 366 | ||||
| -rw-r--r-- | board/garg/board.h | 105 | ||||
| -rw-r--r-- | board/garg/build.mk | 15 | ||||
| -rw-r--r-- | board/garg/ec.tasklist | 25 | ||||
| -rw-r--r-- | board/garg/gpio.inc | 188 | ||||
| -rw-r--r-- | board/garg/led.c | 74 | ||||
| -rw-r--r-- | board/garg/vif_override.xml | 3 |
8 files changed, 0 insertions, 900 deletions
diff --git a/board/garg/battery.c b/board/garg/battery.c deleted file mode 100644 index 046a9b2d56..0000000000 --- a/board/garg/battery.c +++ /dev/null @@ -1,124 +0,0 @@ -/* Copyright 2019 The Chromium OS Authors. All rights reserved. - * Use of this source code is governed by a BSD-style license that can be - * found in the LICENSE file. - * - * Battery pack vendor provided charging profile - */ - -#include "battery_fuel_gauge.h" -#include "common.h" -#include "util.h" - -/* - * Battery info for all garg battery types. Note that the fields - * start_charging_min/max and charging_min/max are not used for the charger. - * The effective temperature limits are given by discharging_min/max_c. - * - * Fuel Gauge (FG) parameters which are used for determining if the battery - * is connected, the appropriate ship mode (battery cutoff) command, and the - * charge/discharge FETs status. - * - * Ship mode (battery cutoff) requires 2 writes to the appropriate smart battery - * register. For some batteries, the charge/discharge FET bits are set when - * charging/discharging is active, in other types, these bits set mean that - * charging/discharging is disabled. Therefore, in addition to the mask for - * these bits, a disconnect value must be specified. Note that for TI fuel - * gauge, the charge/discharge FET status is found in Operation Status (0x54), - * but a read of Manufacturer Access (0x00) will return the lower 16 bits of - * Operation status which contains the FET status bits. - * - * The assumption for battery types supported is that the charge/discharge FET - * status can be read with a sb_read() command and therefore, only the register - * address, mask, and disconnect value need to be provided. - */ -const struct board_batt_params board_battery_info[] = { - /* Simplo SDI 916Q2286H battery information */ - [BATTERY_SIMPLO_SDI] = { - .fuel_gauge = { - .manuf_name = "SMP-SDI3320", - .ship_mode = { - .reg_addr = 0x00, - .reg_data = { 0x0010, 0x0010 }, - }, - .fet = { - .mfgacc_support = 1, - .reg_addr = 0x0, - .reg_mask = 0x0002, - .disconnect_val = 0x0, - }, - }, - .batt_info = { - .voltage_max = TARGET_WITH_MARGIN(13050, 5), /* mV */ - .voltage_normal = 11460, - .voltage_min = 9000, - .precharge_current = 256, /* mA */ - .start_charging_min_c = 0, - .start_charging_max_c = 45, - .charging_min_c = 0, - .charging_max_c = 60, - .discharging_min_c = -20, - .discharging_max_c = 60, - }, - }, - - /* Simplo BYD 916Q2294H battery information */ - [BATTERY_SIMPLO_BYD] = { - .fuel_gauge = { - .manuf_name = "SMP-LP485780", - .ship_mode = { - .reg_addr = 0x00, - .reg_data = { 0x0010, 0x0010 }, - }, - .fet = { - .mfgacc_support = 1, - .reg_addr = 0x0, - .reg_mask = 0x0002, - .disconnect_val = 0x0, - }, - }, - .batt_info = { - .voltage_max = TARGET_WITH_MARGIN(13200, 5), /* mV */ - .voltage_normal = 11550, - .voltage_min = 9000, - .precharge_current = 256, /* mA */ - .start_charging_min_c = 0, - .start_charging_max_c = 45, - .charging_min_c = 0, - .charging_max_c = 45, - .discharging_min_c = -20, - .discharging_max_c = 60, - }, - }, - - /* Simplo CA475778G 916QA141H battery information */ - [BATTERY_SIMPLO_CA475778G] = { - .fuel_gauge = { - .manuf_name = "SMP-CA475778G", - .ship_mode = { - .reg_addr = 0x00, - .reg_data = { 0x0010, 0x0010 }, - }, - .fet = { - .mfgacc_support = 1, - .reg_addr = 0x0, - .reg_mask = 0x0002, - .disconnect_val = 0x0, - }, - }, - .batt_info = { - .voltage_max = 13050, /* mV */ - .voltage_normal = 11430, - .voltage_min = 9000, - .precharge_current = 256, /* mA */ - .start_charging_min_c = 0, - .start_charging_max_c = 45, - .charging_min_c = 0, - .charging_max_c = 45, - .discharging_min_c = -20, - .discharging_max_c = 60, - }, - }, -}; -BUILD_ASSERT(ARRAY_SIZE(board_battery_info) == BATTERY_TYPE_COUNT); - -const enum battery_type DEFAULT_BATTERY_TYPE = BATTERY_SIMPLO_SDI; diff --git a/board/garg/board.c b/board/garg/board.c deleted file mode 100644 index c5e4b4b83f..0000000000 --- a/board/garg/board.c +++ /dev/null @@ -1,366 +0,0 @@ -/* Copyright 2019 The Chromium OS Authors. All rights reserved. - * Use of this source code is governed by a BSD-style license that can be - * found in the LICENSE file. - */ - -/* Garg board-specific configuration */ - -#include "adc.h" -#include "battery.h" -#include "button.h" -#include "cbi_ssfc.h" -#include "charge_manager.h" -#include "charge_state.h" -#include "common.h" -#include "cros_board_info.h" -#include "driver/accel_kionix.h" -#include "driver/accelgyro_bmi_common.h" -#include "driver/accelgyro_icm426xx.h" -#include "driver/accelgyro_icm_common.h" -#include "driver/charger/bd9995x.h" -#include "driver/ppc/nx20p348x.h" -#include "driver/tcpm/anx7447.h" -#include "driver/tcpm/ps8xxx.h" -#include "driver/tcpm/tcpci.h" -#include "driver/tcpm/tcpm.h" -#include "extpower.h" -#include "gpio.h" -#include "hooks.h" -#include "i2c.h" -#include "keyboard_scan.h" -#include "lid_switch.h" -#include "motion_sense.h" -#include "power.h" -#include "power_button.h" -#include "switch.h" -#include "system.h" -#include "tablet_mode.h" -#include "tcpm/tcpci.h" -#include "temp_sensor.h" -#include "temp_sensor/thermistor.h" -#include "usb_mux.h" -#include "usbc_ppc.h" -#include "util.h" - -#define CPRINTSUSB(format, args...) cprints(CC_USBCHARGE, format, ## args) -#define CPRINTFUSB(format, args...) cprintf(CC_USBCHARGE, format, ## args) - -#define USB_PD_PORT_ANX7447 0 -#define USB_PD_PORT_PS8751 1 - -static uint8_t sku_id; - -/* - * We have total 30 pins for keyboard connecter {-1, -1} mean - * the N/A pin that don't consider it and reserve index 0 area - * that we don't have pin 0. - */ -const int keyboard_factory_scan_pins[][2] = { - {-1, -1}, {0, 5}, {1, 1}, {1, 0}, {0, 6}, - {0, 7}, {-1, -1}, {-1, -1}, {1, 4}, {1, 3}, - {-1, -1}, {1, 6}, {1, 7}, {3, 1}, {2, 0}, - {1, 5}, {2, 6}, {2, 7}, {2, 1}, {2, 4}, - {2, 5}, {1, 2}, {2, 3}, {2, 2}, {3, 0}, - {-1, -1}, {0, 4}, {-1, -1}, {8, 2}, {-1, -1}, - {-1, -1}, -}; - -const int keyboard_factory_scan_pins_used = - ARRAY_SIZE(keyboard_factory_scan_pins); - -static void ppc_interrupt(enum gpio_signal signal) -{ - switch (signal) { - case GPIO_USB_PD_C0_INT_ODL: - nx20p348x_interrupt(0); - break; - - case GPIO_USB_PD_C1_INT_ODL: - nx20p348x_interrupt(1); - break; - - default: - break; - } -} - -/* Must come after other header files and GPIO interrupts*/ -#include "gpio_list.h" - -/* ADC channels */ -const struct adc_t adc_channels[] = { - [ADC_TEMP_SENSOR_AMB] = { - "TEMP_AMB", NPCX_ADC_CH0, ADC_MAX_VOLT, ADC_READ_MAX+1, 0}, - [ADC_TEMP_SENSOR_CHARGER] = { - "TEMP_CHARGER", NPCX_ADC_CH1, ADC_MAX_VOLT, ADC_READ_MAX+1, 0}, - /* Vbus sensing (1/10 voltage divider). */ - [ADC_VBUS_C0] = { - "VBUS_C0", NPCX_ADC_CH9, ADC_MAX_VOLT*10, ADC_READ_MAX+1, 0}, - [ADC_VBUS_C1] = { - "VBUS_C1", NPCX_ADC_CH4, ADC_MAX_VOLT*10, ADC_READ_MAX+1, 0}, -}; -BUILD_ASSERT(ARRAY_SIZE(adc_channels) == ADC_CH_COUNT); - -const struct temp_sensor_t temp_sensors[] = { - [TEMP_SENSOR_BATTERY] = {.name = "Battery", - .type = TEMP_SENSOR_TYPE_BATTERY, - .read = charge_get_battery_temp, - .idx = 0}, - [TEMP_SENSOR_AMBIENT] = {.name = "Ambient", - .type = TEMP_SENSOR_TYPE_BOARD, - .read = get_temp_3v3_51k1_47k_4050b, - .idx = ADC_TEMP_SENSOR_AMB}, - [TEMP_SENSOR_CHARGER] = {.name = "Charger", - .type = TEMP_SENSOR_TYPE_BOARD, - .read = get_temp_3v3_13k7_47k_4050b, - .idx = ADC_TEMP_SENSOR_CHARGER}, -}; -BUILD_ASSERT(ARRAY_SIZE(temp_sensors) == TEMP_SENSOR_COUNT); - -/* Motion sensors */ -/* Mutexes */ -static struct mutex g_lid_mutex; -static struct mutex g_base_mutex; - -/* Matrix to rotate accelrator into standard reference frame */ -const mat33_fp_t base_standard_ref = { - { 0, FLOAT_TO_FP(-1), 0}, - { FLOAT_TO_FP(1), 0, 0}, - { 0, 0, FLOAT_TO_FP(1)} -}; - -const mat33_fp_t base_icm_ref = { - { FLOAT_TO_FP(-1), 0, 0}, - { 0, FLOAT_TO_FP(-1), 0}, - { 0, 0, FLOAT_TO_FP(1)} -}; - -/* sensor private data */ -static struct kionix_accel_data g_kx022_data; -static struct bmi_drv_data_t g_bmi160_data; -static struct icm_drv_data_t g_icm426xx_data; - -/* Drivers */ -struct motion_sensor_t motion_sensors[] = { - [LID_ACCEL] = { - .name = "Lid Accel", - .active_mask = SENSOR_ACTIVE_S0_S3, - .chip = MOTIONSENSE_CHIP_KX022, - .type = MOTIONSENSE_TYPE_ACCEL, - .location = MOTIONSENSE_LOC_LID, - .drv = &kionix_accel_drv, - .mutex = &g_lid_mutex, - .drv_data = &g_kx022_data, - .port = I2C_PORT_SENSOR, - .i2c_spi_addr_flags = KX022_ADDR1_FLAGS, - .rot_standard_ref = NULL, /* Identity matrix. */ - .default_range = 2, /* g */ - .min_frequency = KX022_ACCEL_MIN_FREQ, - .max_frequency = KX022_ACCEL_MAX_FREQ, - .config = { - /* EC use accel for angle detection */ - [SENSOR_CONFIG_EC_S0] = { - .odr = 10000 | ROUND_UP_FLAG, - }, - /* Sensor on for lid angle detection */ - [SENSOR_CONFIG_EC_S3] = { - .odr = 10000 | ROUND_UP_FLAG, - }, - }, - }, - [BASE_ACCEL] = { - .name = "Base Accel", - .active_mask = SENSOR_ACTIVE_S0_S3, - .chip = MOTIONSENSE_CHIP_BMI160, - .type = MOTIONSENSE_TYPE_ACCEL, - .location = MOTIONSENSE_LOC_BASE, - .drv = &bmi160_drv, - .mutex = &g_base_mutex, - .drv_data = &g_bmi160_data, - .port = I2C_PORT_SENSOR, - .i2c_spi_addr_flags = BMI160_ADDR0_FLAGS, - .rot_standard_ref = &base_standard_ref, - .default_range = 4, /* g, to meet CDD 7.3.1/C-1-4 reqs */ - .min_frequency = BMI_ACCEL_MIN_FREQ, - .max_frequency = BMI_ACCEL_MAX_FREQ, - .config = { - /* EC use accel for angle detection */ - [SENSOR_CONFIG_EC_S0] = { - .odr = 13000 | ROUND_UP_FLAG, - .ec_rate = 100 * MSEC, - }, - /* Sensor on for angle detection */ - [SENSOR_CONFIG_EC_S3] = { - .odr = 10000 | ROUND_UP_FLAG, - .ec_rate = 100 * MSEC, - }, - }, - }, - [BASE_GYRO] = { - .name = "Base Gyro", - .active_mask = SENSOR_ACTIVE_S0_S3, - .chip = MOTIONSENSE_CHIP_BMI160, - .type = MOTIONSENSE_TYPE_GYRO, - .location = MOTIONSENSE_LOC_BASE, - .drv = &bmi160_drv, - .mutex = &g_base_mutex, - .drv_data = &g_bmi160_data, - .port = I2C_PORT_SENSOR, - .i2c_spi_addr_flags = BMI160_ADDR0_FLAGS, - .default_range = 1000, /* dps */ - .rot_standard_ref = &base_standard_ref, - .min_frequency = BMI_GYRO_MIN_FREQ, - .max_frequency = BMI_GYRO_MAX_FREQ, - }, -}; - -unsigned int motion_sensor_count = ARRAY_SIZE(motion_sensors); - -struct motion_sensor_t icm426xx_base_accel = { - .name = "Base Accel", - .active_mask = SENSOR_ACTIVE_S0_S3, - .chip = MOTIONSENSE_CHIP_ICM426XX, - .type = MOTIONSENSE_TYPE_ACCEL, - .location = MOTIONSENSE_LOC_BASE, - .drv = &icm426xx_drv, - .mutex = &g_base_mutex, - .drv_data = &g_icm426xx_data, - .port = I2C_PORT_SENSOR, - .i2c_spi_addr_flags = ICM426XX_ADDR0_FLAGS, - .rot_standard_ref = &base_icm_ref, - .default_range = 4, /* g */ - .min_frequency = ICM426XX_ACCEL_MIN_FREQ, - .max_frequency = ICM426XX_ACCEL_MAX_FREQ, - .config = { - /* EC use accel for angle detection */ - [SENSOR_CONFIG_EC_S0] = { - .odr = 13000 | ROUND_UP_FLAG, - .ec_rate = 100 * MSEC, - }, - /* Sensor on for angle detection */ - [SENSOR_CONFIG_EC_S3] = { - .odr = 10000 | ROUND_UP_FLAG, - .ec_rate = 100 * MSEC, - }, - }, -}; - -struct motion_sensor_t icm426xx_base_gyro = { - .name = "Base Gyro", - .active_mask = SENSOR_ACTIVE_S0_S3, - .chip = MOTIONSENSE_CHIP_ICM426XX, - .type = MOTIONSENSE_TYPE_GYRO, - .location = MOTIONSENSE_LOC_BASE, - .drv = &icm426xx_drv, - .mutex = &g_base_mutex, - .drv_data = &g_icm426xx_data, - .port = I2C_PORT_SENSOR, - .i2c_spi_addr_flags = ICM426XX_ADDR0_FLAGS, - .default_range = 1000, /* dps */ - .rot_standard_ref = &base_icm_ref, - .min_frequency = ICM426XX_GYRO_MIN_FREQ, - .max_frequency = ICM426XX_GYRO_MAX_FREQ, -}; - -static int board_is_convertible(void) -{ - /* - * Garg360: 37, 38, 39 - * Unprovisioned: 255 - */ - return sku_id == 37 || sku_id == 38 || sku_id == 39 || sku_id == 255; -} - -static void board_update_sensor_config_from_sku(void) -{ - if (board_is_convertible()) { - if (get_cbi_ssfc_sensor() == SSFC_SENSOR_ICM426XX) { - motion_sensors[BASE_ACCEL] = icm426xx_base_accel; - motion_sensors[BASE_GYRO] = icm426xx_base_gyro; - ccprints("BASE GYRO is ICM426XX"); - } else - ccprints("BASE GYRO is BMI160"); - motion_sensor_count = ARRAY_SIZE(motion_sensors); - /* Enable Base Accel interrupt */ - gpio_enable_interrupt(GPIO_BASE_SIXAXIS_INT_L); - } else { - motion_sensor_count = 0; - gmr_tablet_switch_disable(); - /* Base accel is not stuffed, don't allow line to float */ - gpio_set_flags(GPIO_BASE_SIXAXIS_INT_L, - GPIO_INPUT | GPIO_PULL_DOWN); - } -} - -void sensor_interrupt(enum gpio_signal signal) -{ - switch (motion_sensors[BASE_ACCEL].chip) { - case MOTIONSENSE_CHIP_ICM426XX: - icm426xx_interrupt(signal); - break; - case MOTIONSENSE_CHIP_BMI160: - default: - bmi160_interrupt(signal); - break; - } -} - -/* Read CBI from i2c eeprom and initialize variables for board variants */ -static void cbi_init(void) -{ - uint32_t val; - - if (cbi_get_sku_id(&val) != EC_SUCCESS || val > UINT8_MAX) - return; - sku_id = val; - CPRINTSUSB("SKU: %d", sku_id); - - board_update_sensor_config_from_sku(); -} -DECLARE_HOOK(HOOK_INIT, cbi_init, HOOK_PRIO_INIT_I2C + 1); - -void board_hibernate_late(void) -{ - int i; - - const uint32_t hibernate_pins[][2] = { - /* Turn off LEDs before going to hibernate */ - {GPIO_BAT_LED_BLUE_L, GPIO_INPUT | GPIO_PULL_UP}, - {GPIO_BAT_LED_ORANGE_L, GPIO_INPUT | GPIO_PULL_UP}, - }; - - for (i = 0; i < ARRAY_SIZE(hibernate_pins); ++i) - gpio_set_flags(hibernate_pins[i][0], hibernate_pins[i][1]); -} - -/* This callback disables keyboard when convertibles are fully open */ -__override void lid_angle_peripheral_enable(int enable) -{ - /* - * If the lid is in tablet position via other sensors, - * ignore the lid angle, which might be faulty then - * disable keyboard. - */ - if (tablet_get_mode()) - enable = 0; - if (board_is_convertible()) - keyboard_scan_enable(enable, KB_SCAN_DISABLE_LID_ANGLE); -} - -void board_overcurrent_event(int port, int is_overcurrented) -{ - /* Check that port number is valid. */ - if ((port < 0) || (port >= CONFIG_USB_PD_PORT_MAX_COUNT)) - return; - - /* Note that the level is inverted because the pin is active low. */ - gpio_set_level(GPIO_USB_C_OC, !is_overcurrented); -} - -__override uint8_t board_get_usb_pd_port_count(void) -{ - /* HDMI SKU has one USB PD port */ - if (sku_id == 9 || sku_id == 19 || sku_id == 50 || sku_id == 52) - return CONFIG_USB_PD_PORT_MAX_COUNT - 1; - return CONFIG_USB_PD_PORT_MAX_COUNT; -} diff --git a/board/garg/board.h b/board/garg/board.h deleted file mode 100644 index 273601824c..0000000000 --- a/board/garg/board.h +++ /dev/null @@ -1,105 +0,0 @@ -/* Copyright 2019 The Chromium OS Authors. All rights reserved. - * Use of this source code is governed by a BSD-style license that can be - * found in the LICENSE file. - */ - -/* Garg board configuration */ - -#ifndef __CROS_EC_BOARD_H -#define __CROS_EC_BOARD_H - -/* Free up flash space */ -#define CONFIG_LTO - -/* Select Baseboard features */ -#define VARIANT_OCTOPUS_EC_NPCX796FB -#define VARIANT_OCTOPUS_CHARGER_ISL9238 -#include "baseboard.h" - -/* I2C bus configuraiton */ -#define I2C_PORT_ACCEL I2C_PORT_SENSOR - -/* EC console commands */ -#define CONFIG_CMD_ACCELS -#define CONFIG_CMD_ACCEL_INFO - -#define CONFIG_LED_COMMON - -/* Sensors */ -#define CONFIG_ACCEL_KX022 /* Lid accel */ -#define CONFIG_ACCELGYRO_BMI160 /* Base accel */ -#define CONFIG_ACCELGYRO_ICM426XX /* 2nd Base accel */ -#define CONFIG_SYNC /* Camera VSYNC */ - -#define CONFIG_DYNAMIC_MOTION_SENSOR_COUNT -/* Sensors without hardware FIFO are in forced mode */ -#define CONFIG_ACCEL_FORCE_MODE_MASK BIT(LID_ACCEL) - -/* Motion Sense Task Events */ -#define CONFIG_ACCELGYRO_BMI160_INT_EVENT \ - TASK_EVENT_MOTION_SENSOR_INTERRUPT(BASE_ACCEL) -#define CONFIG_ACCELGYRO_ICM426XX_INT_EVENT \ - TASK_EVENT_MOTION_SENSOR_INTERRUPT(BASE_ACCEL) - -#define CONFIG_SYNC_INT_EVENT \ - TASK_EVENT_MOTION_SENSOR_INTERRUPT(VSYNC) - -#define CONFIG_LID_ANGLE -#define CONFIG_LID_ANGLE_UPDATE -#define CONFIG_LID_ANGLE_SENSOR_BASE BASE_ACCEL -#define CONFIG_LID_ANGLE_SENSOR_LID LID_ACCEL - -#define CONFIG_VOLUME_BUTTONS -#define GPIO_VOLUME_UP_L GPIO_EC_VOLUP_BTN_ODL -#define GPIO_VOLUME_DOWN_L GPIO_EC_VOLDN_BTN_ODL - -#define CONFIG_TEMP_SENSOR -#define CONFIG_THERMISTOR -#define CONFIG_STEINHART_HART_3V3_13K7_47K_4050B -#define CONFIG_STEINHART_HART_3V3_51K1_47K_4050B - -#ifndef __ASSEMBLER__ - -/* support factory keyboard test */ -#define CONFIG_KEYBOARD_FACTORY_TEST - -#include "gpio_signal.h" -#include "registers.h" - -enum adc_channel { - ADC_TEMP_SENSOR_AMB, /* ADC0 */ - ADC_TEMP_SENSOR_CHARGER, /* ADC1 */ - ADC_VBUS_C0, /* ADC9 */ - ADC_VBUS_C1, /* ADC4 */ - ADC_CH_COUNT -}; - -enum temp_sensor_id { - TEMP_SENSOR_BATTERY, - TEMP_SENSOR_AMBIENT, - TEMP_SENSOR_CHARGER, - TEMP_SENSOR_COUNT -}; - -/* Motion sensors */ -enum sensor_id { - LID_ACCEL, - BASE_ACCEL, - BASE_GYRO, - VSYNC, - SENSOR_COUNT -}; - -/* List of possible batteries */ -enum battery_type { - BATTERY_SIMPLO_SDI, - BATTERY_SIMPLO_BYD, - BATTERY_SIMPLO_CA475778G, - BATTERY_TYPE_COUNT, -}; - -void sensor_interrupt(enum gpio_signal signal); - -#endif /* !__ASSEMBLER__ */ - -#endif /* __CROS_EC_BOARD_H */ diff --git a/board/garg/build.mk b/board/garg/build.mk deleted file mode 100644 index 137e208b53..0000000000 --- a/board/garg/build.mk +++ /dev/null @@ -1,15 +0,0 @@ -# -*- makefile -*- -# Copyright 2019 The Chromium OS Authors. All rights reserved. -# Use of this source code is governed by a BSD-style license that can be -# found in the LICENSE file. -# -# Board specific files build -# - -CHIP:=npcx -CHIP_FAMILY:=npcx7 -CHIP_VARIANT:=npcx7m6fb -BASEBOARD:=octopus - -board-y=board.o led.o -board-$(CONFIG_BATTERY_SMART)+=battery.o diff --git a/board/garg/ec.tasklist b/board/garg/ec.tasklist deleted file mode 100644 index 6eac78a042..0000000000 --- a/board/garg/ec.tasklist +++ /dev/null @@ -1,25 +0,0 @@ -/* Copyright 2019 The Chromium OS Authors. All rights reserved. - * Use of this source code is governed by a BSD-style license that can be - * found in the LICENSE file. - */ - -/* - * See CONFIG_TASK_LIST in config.h for details. - */ - -#define CONFIG_TASK_LIST \ - TASK_ALWAYS(HOOKS, hook_task, NULL, VENTI_TASK_STACK_SIZE) \ - TASK_ALWAYS(USB_CHG_P0, usb_charger_task, 0, LARGER_TASK_STACK_SIZE) \ - TASK_ALWAYS(USB_CHG_P1, usb_charger_task, 1, LARGER_TASK_STACK_SIZE) \ - TASK_ALWAYS(CHARGER, charger_task, NULL, VENTI_TASK_STACK_SIZE) \ - TASK_ALWAYS(MOTIONSENSE, motion_sense_task, NULL, VENTI_TASK_STACK_SIZE) \ - TASK_NOTEST(CHIPSET, chipset_task, NULL, VENTI_TASK_STACK_SIZE) \ - TASK_NOTEST(KEYPROTO, keyboard_protocol_task, NULL, TASK_STACK_SIZE) \ - TASK_ALWAYS(HOSTCMD, host_command_task, NULL, VENTI_TASK_STACK_SIZE) \ - TASK_ALWAYS(CONSOLE, console_task, NULL, VENTI_TASK_STACK_SIZE) \ - TASK_ALWAYS(POWERBTN, power_button_task, NULL, VENTI_TASK_STACK_SIZE) \ - TASK_NOTEST(KEYSCAN, keyboard_scan_task, NULL, VENTI_TASK_STACK_SIZE) \ - TASK_ALWAYS(PD_C0, pd_task, NULL, VENTI_TASK_STACK_SIZE) \ - TASK_ALWAYS(PD_C1, pd_task, NULL, VENTI_TASK_STACK_SIZE) \ - TASK_ALWAYS(PD_INT_C0, pd_interrupt_handler_task, 0, VENTI_TASK_STACK_SIZE) \ - TASK_ALWAYS(PD_INT_C1, pd_interrupt_handler_task, 1, VENTI_TASK_STACK_SIZE) diff --git a/board/garg/gpio.inc b/board/garg/gpio.inc deleted file mode 100644 index 995986d600..0000000000 --- a/board/garg/gpio.inc +++ /dev/null @@ -1,188 +0,0 @@ -/* -*- mode:c -*- - * - * Copyright 2019 The Chromium OS Authors. All rights reserved. - * Use of this source code is governed by a BSD-style license that can be - * found in the LICENSE file. - */ - -/* Declare symbolic names for all the GPIOs that we care about. - * Note: Those with interrupt handlers must be declared first. */ - -/* Wake Source interrupts */ -GPIO_INT(LID_OPEN, PIN(D, 2), GPIO_INT_BOTH | - GPIO_HIB_WAKE_HIGH, lid_interrupt) -GPIO_INT(POWER_BUTTON_L, PIN(0, 1), GPIO_INT_BOTH, power_button_interrupt) /* MECH_PWR_BTN_ODL */ -GPIO_INT(AC_PRESENT, PIN(0, 0), GPIO_INT_BOTH | - GPIO_HIB_WAKE_HIGH, extpower_interrupt) /* ACOK_OD */ - -/* USB-C interrupts */ -GPIO_INT(USB_C0_MUX_INT_ODL, PIN(6, 1), GPIO_INT_FALLING, tcpc_alert_event) -GPIO_INT(USB_C1_MUX_INT_ODL, PIN(F, 5), GPIO_INT_FALLING, tcpc_alert_event) -GPIO_INT(USB_PD_C0_INT_ODL, PIN(E, 0), GPIO_INT_FALLING, ppc_interrupt) -GPIO_INT(USB_PD_C1_INT_ODL, PIN(F, 1), GPIO_INT_FALLING, ppc_interrupt) - -/* Power State interrupts */ -#ifdef CONFIG_POWER_S0IX -GPIO_INT(PCH_SLP_S0_L, PIN(A, 4), GPIO_INT_BOTH, power_signal_interrupt) /* SLP_S0_L */ -#endif -GPIO_INT(PCH_SLP_S4_L, PIN(A, 3), GPIO_INT_BOTH, power_signal_interrupt) /* SLP_S4_L */ -GPIO_INT(PCH_SLP_S3_L, PIN(A, 6), GPIO_INT_BOTH, power_signal_interrupt) /* SLP_S3_L */ -GPIO_INT(SUSPWRDNACK, PIN(D, 5), GPIO_INT_BOTH, power_signal_interrupt) /* SUSPWRDNACK */ -GPIO_INT(RSMRST_L_PGOOD, PIN(E, 2), GPIO_INT_BOTH, power_signal_interrupt) /* PMIC_EC_RSMRST_ODL */ -GPIO_INT(ALL_SYS_PGOOD, PIN(F, 4), GPIO_INT_BOTH, power_signal_interrupt) /* PMIC_EC_PWROK_OD */ - -/* Other interrupts */ -GPIO_INT(WP_L, PIN(A, 1), GPIO_INT_BOTH, switch_interrupt) /* EC_WP_ODL */ -GPIO_INT(TABLET_MODE_L, PIN(8, 6), GPIO_INT_BOTH, gmr_tablet_switch_isr) -GPIO_INT(EC_VOLUP_BTN_ODL, PIN(7, 5), GPIO_INT_BOTH, button_interrupt) -GPIO_INT(EC_VOLDN_BTN_ODL, PIN(4, 0), GPIO_INT_BOTH, button_interrupt) - -GPIO_INT(BASE_SIXAXIS_INT_L, PIN(5, 6), GPIO_INT_FALLING | GPIO_SEL_1P8V, sensor_interrupt) - -GPIO(LID_ACCEL_INT_L, PIN(5, 0), GPIO_INPUT | GPIO_SEL_1P8V) - -/* Define PCH_SLP_S0_L after all interrupts if CONFIG_POWER_S0IX not defined. */ -#ifndef CONFIG_POWER_S0IX -GPIO(PCH_SLP_S0_L, PIN(A, 4), GPIO_INPUT) /* SLP_S0_L */ -#endif - -/* - * PLT_RST_L isn't used since there is a Virtual Wire on eSPI for it. It is here - * only for debugging purposes. - */ -GPIO(PLT_RST_L, PIN(C, 7), GPIO_INPUT) /* Platform Reset from SoC */ -GPIO(SYS_RESET_L, PIN(3, 4), GPIO_ODR_HIGH) /* SYS_RST_ODL */ -GPIO(PCH_RTCRST, PIN(7, 6), GPIO_OUT_LOW) /* EC_PCH_RTCRST */ - -GPIO(ENTERING_RW, PIN(E, 1), GPIO_OUT_LOW) /* EC_ENTERING_RW */ -GPIO(PCH_WAKE_L, PIN(7, 4), GPIO_ODR_HIGH) /* EC_PCH_WAKE_ODL */ -GPIO(PCH_PWRBTN_L, PIN(C, 1), GPIO_ODR_HIGH) /* EC_PCH_PWR_BTN_ODL */ - -GPIO(EN_PP5000, PIN(7, 3), GPIO_OUT_LOW) /* EN_PP5000_A */ -GPIO(PP5000_PG, PIN(C, 0), GPIO_INPUT) /* PP5000_PG_OD */ -GPIO(EN_PP3300, PIN(D, 4), GPIO_OUT_LOW) /* EN_PP3300_A */ -GPIO(PP3300_PG, PIN(6, 0), GPIO_INPUT) /* PP3300_PG_OD */ -GPIO(PMIC_EN, PIN(7, 2), GPIO_OUT_LOW) /* Enable A Rails via PMIC */ -GPIO(PCH_RSMRST_L, PIN(C, 2), GPIO_OUT_LOW) /* RSMRST# to SOC. All _A rails now up. */ -GPIO(PCH_SYS_PWROK, PIN(B, 7), GPIO_OUT_LOW) /* EC_PCH_PWROK. All S0 rails now up. */ - -/* Peripheral rails */ -GPIO(ENABLE_BACKLIGHT, PIN(D, 3), GPIO_ODR_HIGH | - GPIO_SEL_1P8V) /* EC_BL_EN_OD */ -GPIO(EN_P3300_TRACKPAD_ODL, PIN(3, 3), GPIO_ODR_HIGH) - -GPIO(EC_BATT_PRES_L, PIN(E, 5), GPIO_INPUT) - -/* - * EC_RST_ODL acts as a wake source from PSL hibernate mode. However, it does - * not need to be an interrupt for normal EC operations. Thus, configure it as - * GPIO_INPUT with wake on low-to-high edge using GPIO_HIB_WAKE_HIGH so that PSL - * common code can configure PSL_IN correctly. - * - * Reason for choosing low-to-high edge for waking from hibernate is to avoid - * the double reset - one because of PSL_IN wake and other because of VCC1_RST - * being asserted. Also, it should be fine to have the EC in hibernate when H1 - * or servo wants to hold the EC in reset since VCC1 will be down and so entire - * EC logic (except PSL) as well as AP will be in reset. - * - * We need to lock the setting so this gpio can't be reconfigured to overdrive - * the real reset signal. (This is the PSL input pin not the real reset pin). - */ -GPIO(EC_RST_ODL, PIN(0, 2), GPIO_INT_BOTH | - GPIO_HIB_WAKE_HIGH | - GPIO_LOCKED) - -/* - * PCH_PROCHOT_ODL is primarily for monitoring the PROCHOT# signal which is - * normally driven by the PMIC. The EC can also drive this signal in the event - * that the ambient or charger temperature sensors exceeds their thresholds. - */ -GPIO(CPU_PROCHOT, PIN(3, 7), GPIO_INPUT | GPIO_SEL_1P8V) /* PCH_PROCHOT_ODL */ - -/* I2C pins - Alternate function below configures I2C module on these pins */ -GPIO(I2C0_SCL, PIN(B, 5), GPIO_INPUT) /* EC_I2C_BATTERY_3V3_SCL */ -GPIO(I2C0_SDA, PIN(B, 4), GPIO_INPUT) /* EC_I2C_BATTERY_3V3_SDA */ -GPIO(I2C1_SCL, PIN(9, 0), GPIO_INPUT) /* EC_I2C_USB_C0_MUX_SCL */ -GPIO(I2C1_SDA, PIN(8, 7), GPIO_INPUT) /* EC_I2C_USB_C0_MUX_SDA */ -GPIO(I2C2_SCL, PIN(9, 2), GPIO_INPUT) /* EC_I2C_USB_C1_MUX_SCL */ -GPIO(I2C2_SDA, PIN(9, 1), GPIO_INPUT) /* EC_I2C_USB_C1_MUX_SDA */ -GPIO(I2C3_SCL, PIN(D, 1), GPIO_INPUT) /* EC_I2C_EEPROM_SCL */ -GPIO(I2C3_SDA, PIN(D, 0), GPIO_INPUT) /* EC_I2C_EEPROM_SDA */ -GPIO(I2C4_SCL, PIN(F, 3), GPIO_INPUT) /* EC_I2C_CHARGER_3V3_SCL */ -GPIO(I2C4_SDA, PIN(F, 2), GPIO_INPUT) /* EC_I2C_CHARGER_3V3_SDA */ -GPIO(I2C7_SCL, PIN(B, 3), GPIO_INPUT | - GPIO_SEL_1P8V) /* EC_I2C_SENSOR_U_SCL */ -GPIO(I2C7_SDA, PIN(B, 2), GPIO_INPUT | - GPIO_SEL_1P8V) /* EC_I2C_SENSOR_U_SDA */ - -/* USB pins */ -GPIO(EN_USB_A0_5V, PIN(6, 7), GPIO_OUT_LOW) /* Enable A0 5V Charging */ -GPIO(EN_USB_A1_5V, PIN(9, 6), GPIO_OUT_LOW) /* Enable A1 5V Charging */ -GPIO(USB_A0_CHARGE_EN_L, PIN(A, 2), GPIO_OUT_HIGH) /* Enable A0 1.5A Charging */ -GPIO(USB_A1_CHARGE_EN_L, PIN(A, 0), GPIO_OUT_HIGH) /* Enable A1 1.5A Charging */ -GPIO(USB_C0_PD_RST, PIN(8, 3), GPIO_OUT_LOW) /* C0 PD Reset */ -GPIO(USB_C0_BC12_VBUS_ON, PIN(6, 3), GPIO_OUT_LOW) /* C0 BC1.2 Power */ -GPIO(USB_C0_BC12_CHG_DET_L, PIN(9, 5), GPIO_INPUT) /* C0 BC1.2 Detect */ -GPIO(USB_C0_HPD_1V8_ODL, PIN(C, 5), GPIO_INPUT | /* C0 DP Hotplug Detect */ - GPIO_SEL_1P8V) -GPIO(USB_C1_PD_RST_ODL, PIN(7, 0), GPIO_ODR_HIGH) /* C1 PD Reset */ -GPIO(USB_C1_BC12_VBUS_ON, PIN(B, 1), GPIO_OUT_LOW) /* C1 BC1.2 Power */ -GPIO(USB_C1_BC12_CHG_DET_L, PIN(E, 4), GPIO_INPUT) /* C1 BC1.2 Detect */ -GPIO(USB_C1_HPD_1V8_ODL, PIN(C, 6), GPIO_INPUT | /* C1 DP Hotplug Detect */ - GPIO_SEL_1P8V) - -/* LED */ -GPIO(BAT_LED_ORANGE_L, PIN(C, 3), GPIO_OUT_HIGH) /* LED_1_L */ -GPIO(BAT_LED_BLUE_L, PIN(C, 4), GPIO_OUT_HIGH) /* LED_2_L */ -GPIO(LED_3_L, PIN(D, 7), GPIO_OUT_HIGH) - -/* MKBP event synchronization */ -GPIO(EC_INT_L, PIN(9, 4), GPIO_ODR_HIGH) - -/* Overcurrent event to host */ -GPIO(USB_C_OC, PIN(3, 6), GPIO_ODR_HIGH | GPIO_SEL_1P8V) - -/* Misc. */ -GPIO(CCD_MODE_EC_L, PIN(E, 3), GPIO_INPUT) -GPIO(TRACKPAD_INT_1V8_ODL, PIN(9, 3), GPIO_INPUT | GPIO_SEL_1P8V) - -/* Unused Pins */ -GPIO(CHARGER_PMON, PIN(4, 2), GPIO_INPUT) -GPIO(CHARGER_IADP, PIN(4, 3), GPIO_INPUT) -GPIO(EC_GPIO57, PIN(5, 7), GPIO_INPUT | GPIO_PULL_UP) /* TP Only */ -GPIO(EC_GPIO97, PIN(9, 7), GPIO_INPUT | GPIO_PULL_UP) /* TP Only */ -GPIO(EC_I2S_SFRM, PIN(A, 5), GPIO_INPUT | GPIO_SEL_1P8V) -GPIO(EC_I2S_SCLK, PIN(A, 7), GPIO_INPUT | GPIO_SEL_1P8V) -GPIO(EC_I2S_TX_PCH_RX, PIN(B, 0), GPIO_INPUT | GPIO_SEL_1P8V) -GPIO(WFCAM_VSYNC, PIN(0, 3), GPIO_INPUT) -GPIO(KB_BL_PWR_EN, PIN(6, 2), GPIO_INPUT) -GPIO(EC_GPIO80, PIN(8, 0), GPIO_INPUT) - -/* Keyboard pins */ -ALTERNATE(PIN_MASK(3, 0x03), 0, MODULE_KEYBOARD_SCAN, GPIO_INPUT) /* KSI_00-01 */ -ALTERNATE(PIN_MASK(2, 0xFC), 0, MODULE_KEYBOARD_SCAN, GPIO_INPUT) /* KSI_02-07 */ -ALTERNATE(PIN_MASK(2, 0x03), 0, MODULE_KEYBOARD_SCAN, GPIO_ODR_HIGH) /* KSO_00-01 */ -ALTERNATE(PIN_MASK(1, 0x7F), 0, MODULE_KEYBOARD_SCAN, GPIO_ODR_HIGH) /* KSO_03-09 */ -ALTERNATE(PIN_MASK(0, 0xF0), 0, MODULE_KEYBOARD_SCAN, GPIO_ODR_HIGH) /* KSO_10-13 */ -ALTERNATE(PIN_MASK(8, 0x04), 0, MODULE_KEYBOARD_SCAN, GPIO_ODR_HIGH) /* KSO_14 */ - -GPIO(KBD_KSO2, PIN(1, 7), GPIO_OUT_LOW) /* KSO_02 inverted */ - -/* Alternate functions GPIO definitions */ -/* Cr50 requires no pull-ups on UART pins. */ -ALTERNATE(PIN_MASK(6, 0x30), 0, MODULE_UART, 0) /* UART from EC to Servo */ -ALTERNATE(PIN_MASK(B, 0x30), 0, MODULE_I2C, 0) /* I2C0 */ -ALTERNATE(PIN_MASK(9, 0x07), 0, MODULE_I2C, 0) /* I2C1 SCL / I2C2 */ -ALTERNATE(PIN_MASK(8, 0x80), 0, MODULE_I2C, 0) /* I2C1 SDA */ -ALTERNATE(PIN_MASK(D, 0x03), 0, MODULE_I2C, 0) /* I2C3 */ -ALTERNATE(PIN_MASK(F, 0x0C), 0, MODULE_I2C, 0) /* I2C4 */ -ALTERNATE(PIN_MASK(B, 0x0C), 0, MODULE_I2C, (GPIO_INPUT | GPIO_SEL_1P8V)) /* 1.8V I2C7 */ -ALTERNATE(PIN_MASK(4, 0x30), 0, MODULE_ADC, 0) /* ADC0-1 */ -ALTERNATE(PIN_MASK(4, 0x02), 0, MODULE_ADC, 0) /* ADC4 */ -ALTERNATE(PIN_MASK(F, 0x01), 0, MODULE_ADC, 0) /* ADC9 */ - -/* Power Switch Logic (PSL) inputs */ -ALTERNATE(PIN_MASK(D, 0x04), 0, MODULE_PMU, 0) /* GPIOD2 = LID_OPEN */ -ALTERNATE(PIN_MASK(0, 0x07), 0, MODULE_PMU, 0) /* GPIO00 = ACOK_OD, - GPIO01 = MECH_PWR_BTN_ODL - GPIO02 = EC_RST_ODL */ diff --git a/board/garg/led.c b/board/garg/led.c deleted file mode 100644 index 6e0306edd9..0000000000 --- a/board/garg/led.c +++ /dev/null @@ -1,74 +0,0 @@ -/* Copyright 2019 The Chromium OS Authors. All rights reserved. - * Use of this source code is governed by a BSD-style license that can be - * found in the LICENSE file. - * - * Power and battery LED control for Garg - */ - -#include "ec_commands.h" -#include "gpio.h" -#include "led_common.h" -#include "led_onoff_states.h" - -#define LED_OFF_LVL 1 -#define LED_ON_LVL 0 - -__override const int led_charge_lvl_1; - -__override const int led_charge_lvl_2 = 100; - -/* Garg: Note there is only LED for charge / power */ -__override struct led_descriptor - led_bat_state_table[LED_NUM_STATES][LED_NUM_PHASES] = { - [STATE_CHARGING_LVL_2] = {{EC_LED_COLOR_AMBER, LED_INDEFINITE} }, - [STATE_CHARGING_FULL_CHARGE] = {{EC_LED_COLOR_BLUE, LED_INDEFINITE} }, - [STATE_DISCHARGE_S0] = {{EC_LED_COLOR_BLUE, LED_INDEFINITE} }, - [STATE_DISCHARGE_S3] = {{EC_LED_COLOR_AMBER, 1 * LED_ONE_SEC}, - {LED_OFF, 3 * LED_ONE_SEC} }, - [STATE_DISCHARGE_S5] = {{LED_OFF, LED_INDEFINITE} }, - [STATE_BATTERY_ERROR] = {{EC_LED_COLOR_AMBER, 1 * LED_ONE_SEC}, - {LED_OFF, 1 * LED_ONE_SEC} }, - [STATE_FACTORY_TEST] = {{EC_LED_COLOR_BLUE, 2 * LED_ONE_SEC}, - {EC_LED_COLOR_AMBER, 2 * LED_ONE_SEC} }, -}; - -const enum ec_led_id supported_led_ids[] = { EC_LED_ID_BATTERY_LED }; - -const int supported_led_ids_count = ARRAY_SIZE(supported_led_ids); - -__override void led_set_color_battery(enum ec_led_colors color) -{ - switch (color) { - case EC_LED_COLOR_BLUE: - gpio_set_level(GPIO_BAT_LED_BLUE_L, LED_ON_LVL); - gpio_set_level(GPIO_BAT_LED_ORANGE_L, LED_OFF_LVL); - break; - case EC_LED_COLOR_AMBER: - gpio_set_level(GPIO_BAT_LED_BLUE_L, LED_OFF_LVL); - gpio_set_level(GPIO_BAT_LED_ORANGE_L, LED_ON_LVL); - break; - default: /* LED_OFF and other unsupported colors */ - gpio_set_level(GPIO_BAT_LED_BLUE_L, LED_OFF_LVL); - gpio_set_level(GPIO_BAT_LED_ORANGE_L, LED_OFF_LVL); - break; - } -} - -void led_get_brightness_range(enum ec_led_id led_id, uint8_t *brightness_range) -{ - brightness_range[EC_LED_COLOR_BLUE] = 1; - brightness_range[EC_LED_COLOR_AMBER] = 1; -} - -int led_set_brightness(enum ec_led_id led_id, const uint8_t *brightness) -{ - if (brightness[EC_LED_COLOR_BLUE] != 0) - led_set_color_battery(EC_LED_COLOR_BLUE); - else if (brightness[EC_LED_COLOR_AMBER] != 0) - led_set_color_battery(EC_LED_COLOR_AMBER); - else - led_set_color_battery(LED_OFF); - - return EC_SUCCESS; -} - diff --git a/board/garg/vif_override.xml b/board/garg/vif_override.xml deleted file mode 100644 index 32736caf64..0000000000 --- a/board/garg/vif_override.xml +++ /dev/null @@ -1,3 +0,0 @@ -<!-- Add VIF field overrides here. See genvif.c and the Vendor Info File - Definition from the USB-IF. ---> |