diff options
Diffstat (limited to 'board/halvor/board.h')
| -rw-r--r-- | board/halvor/board.h | 176 |
1 files changed, 0 insertions, 176 deletions
diff --git a/board/halvor/board.h b/board/halvor/board.h deleted file mode 100644 index 818b4b79e5..0000000000 --- a/board/halvor/board.h +++ /dev/null @@ -1,176 +0,0 @@ -/* Copyright 2020 The Chromium OS Authors. All rights reserved. - * Use of this source code is governed by a BSD-style license that can be - * found in the LICENSE file. - */ - -/* Volteer board configuration */ - -#ifndef __CROS_EC_BOARD_H -#define __CROS_EC_BOARD_H - -/* Baseboard features */ -#include "baseboard.h" - -/* Optional features */ -#define CONFIG_SYSTEM_UNLOCKED /* Allow dangerous commands while in dev. */ - -#define CONFIG_POWER_BUTTON - -#undef CONFIG_UART_TX_BUF_SIZE -#define CONFIG_UART_TX_BUF_SIZE 4096 - -/* LED defines */ -#define CONFIG_LED_ONOFF_STATES -#define CONFIG_LED_ONOFF_STATES_BAT_LOW 10 - -/* Keyboard features */ - -/* Sensors */ -/* BMA253 accelerometer in base */ -#define CONFIG_ACCEL_BMA255 - -/* TCS3400 ALS */ -#define CONFIG_ALS -#define ALS_COUNT 1 -#define CONFIG_ALS_TCS3400 -#define CONFIG_ALS_TCS3400_INT_EVENT \ - TASK_EVENT_MOTION_SENSOR_INTERRUPT(CLEAR_ALS) - -/* Sensors without hardware FIFO are in forced mode */ -#define CONFIG_ACCEL_FORCE_MODE_MASK \ - (BIT(LID_ACCEL) | BIT(CLEAR_ALS)) - -/* USB Type C and USB PD defines */ -#define CONFIG_USB_PD_PORT_MAX_COUNT 3 - -#define PD_POWER_SUPPLY_TURN_ON_DELAY 30000 /* us */ -#define PD_POWER_SUPPLY_TURN_OFF_DELAY 250000 /* us */ - -/* - * SN5S30 PPC supports up to 24V VBUS source and sink, however passive USB-C - * cables only support up to 60W. - */ -#define PD_OPERATING_POWER_MW 15000 -#define PD_MAX_POWER_MW 65000 -#define PD_MAX_CURRENT_MA 3250 -#define PD_MAX_VOLTAGE_MV 20000 - -/* Enabling Thunderbolt-compatible mode */ -#define CONFIG_USB_PD_TBT_COMPAT_MODE - -/* Enabling USB4 mode */ -#define CONFIG_USB_PD_USB4 -#define USBC_PORT_C0_BB_RETIMER_I2C_ADDR 0x40 -#define USBC_PORT_C1_BB_RETIMER_I2C_ADDR 0x41 -#define USBC_PORT_C2_BB_RETIMER_I2C_ADDR 0x42 - -/* USB Type A Features */ - -/* USBC PPC*/ -#define CONFIG_USBC_PPC_SYV682X /* USBC port C0 C1 C2 */ - -/* BC 1.2 */ - -/* Volume Button feature */ - -/* Fan features */ - -/* charger defines */ -#define CONFIG_CHARGER_SENSE_RESISTOR 5 -#define CONFIG_CHARGER_SENSE_RESISTOR_AC 10 - -/* - * Macros for GPIO signals used in common code that don't match the - * schematic names. Signal names in gpio.inc match the schematic and are - * then redefined here to so it's more clear which signal is being used for - * which purpose. - */ -#define GPIO_AC_PRESENT GPIO_ACOK_OD -#define GPIO_EC_INT_L GPIO_EC_PCH_INT_ODL -#define GPIO_EN_PP5000 GPIO_EN_PP5000_A -#define GPIO_ENTERING_RW GPIO_EC_ENTERING_RW -#define GPIO_LID_OPEN GPIO_EC_LID_OPEN -#define GPIO_KBD_KSO2 GPIO_EC_KSO_02_INV -#define GPIO_PCH_WAKE_L GPIO_EC_PCH_WAKE_ODL -#define GPIO_PCH_PWRBTN_L GPIO_EC_PCH_PWR_BTN_ODL -#define GPIO_PCH_RSMRST_L GPIO_EC_PCH_RSMRST_ODL -#define GPIO_PCH_RTCRST GPIO_EC_PCH_RTCRST -#define GPIO_PCH_SYS_PWROK GPIO_EC_PCH_SYS_PWROK -#define GPIO_PCH_SLP_S0_L GPIO_SLP_S0_L -#define GPIO_PCH_SLP_S3_L GPIO_SLP_S3_L -#define GPIO_PG_EC_DSW_PWROK GPIO_DSW_PWROK -#define GPIO_POWER_BUTTON_L GPIO_H1_EC_PWR_BTN_ODL -#define GPIO_RSMRST_L_PGOOD GPIO_PG_EC_RSMRST_ODL -#define GPIO_CPU_PROCHOT GPIO_EC_PROCHOT_ODL -#define GPIO_SYS_RESET_L GPIO_SYS_RST_ODL -#define GPIO_USB_C0_BC12_INT_ODL GPIO_USB_C0_MIX_INT_ODL -#define GPIO_USB_C1_BC12_INT_ODL GPIO_USB_C1_MIX_INT_ODL -#define GPIO_USB_C2_BC12_INT_ODL GPIO_USB_C2_MIX_INT_ODL -#define GPIO_WP_L GPIO_EC_WP_L -#define GMR_TABLET_MODE_GPIO_L GPIO_TABLET_MODE_L - -#undef CONFIG_FANS -#undef CONFIG_VOLUME_BUTTONS - -/* I2C Bus Configuration */ -#define CONFIG_I2C -#define I2C_PORT_SENSOR NPCX_I2C_PORT0_0 -#define I2C_PORT_USB_C0 NPCX_I2C_PORT1_0 -#define I2C_PORT_USB_C1 NPCX_I2C_PORT2_0 -#define I2C_PORT_USB_BB_RETIMER NPCX_I2C_PORT3_0 -#define I2C_PORT_USB_C2 NPCX_I2C_PORT4_1 -#define I2C_PORT_POWER NPCX_I2C_PORT5_0 -#define I2C_PORT_EEPROM NPCX_I2C_PORT7_0 - -#define I2C_PORT_BATTERY I2C_PORT_POWER -#define I2C_PORT_CHARGER I2C_PORT_EEPROM -#define I2C_PORT_USB_1_MIX I2C_PORT_USB_BB_RETIMER - -#define I2C_ADDR_EEPROM_FLAGS 0x50 -#define CONFIG_I2C_CONTROLLER - - -#ifndef __ASSEMBLER__ - -#include "gpio_signal.h" -#include "registers.h" - -enum battery_type { - BATTERY_AEC, - BATTERY_TYPE_COUNT, -}; - -enum pwm_channel { - PWM_CH_LED1_BLUE = 0, - PWM_CH_LED2_GREEN, - PWM_CH_LED3_RED, - PWM_CH_LED4_SIDESEL, - PWM_CH_FAN, - PWM_CH_KBLIGHT, - PWM_CH_COUNT -}; - -enum sensor_id { - LID_ACCEL = 0, - CLEAR_ALS, - RGB_ALS, - SENSOR_COUNT, -}; - -enum usbc_port { - USBC_PORT_C0 = 0, - USBC_PORT_C1, - USBC_PORT_C2, - USBC_PORT_COUNT -}; - -/* Definition for Halvor USB PD interrupt handlers. */ -void halvor_tcpc_alert_event(enum gpio_signal signal); -void halvor_ppc_interrupt(enum gpio_signal signal); -void halvor_bc12_interrupt(enum gpio_signal signal); - -void board_reset_pd_mcu(void); - -#endif /* !__ASSEMBLER__ */ - -#endif /* __CROS_EC_BOARD_H */ |