1 files changed, 0 insertions, 126 deletions
diff --git a/board/katsu/board.h b/board/katsu/board.h
deleted file mode 100644
index aa6e386d8f..0000000000
--- a/board/katsu/board.h
+++ /dev/null
@@ -1,126 +0,0 @@
-/* Copyright 2020 The Chromium OS Authors. All rights reserved.
- * Use of this source code is governed by a BSD-style license that can be
- * found in the LICENSE file.
- */
-
-/* Configuration for Katsu */
-
-#ifndef __CROS_EC_BOARD_H
-#define __CROS_EC_BOARD_H
-
-#define BQ27541_ADDR	0x55
-#define VARIANT_KUKUI_BATTERY_BQ27541
-#define VARIANT_KUKUI_POGO_KEYBOARD
-
-#define VARIANT_KUKUI_CHARGER_MT6370
-#define VARIANT_KUKUI_EC_STM32F098
-#define VARIANT_KUKUI_TABLET_PWRBTN
-
-#ifndef SECTION_IS_RW
-#define VARIANT_KUKUI_NO_SENSORS
-#endif /* SECTION_IS_RW */
-
-#include "baseboard.h"
-
-#define CONFIG_USB_MUX_IT5205
-#define CONFIG_VOLUME_BUTTONS
-#define CONFIG_USB_MUX_RUNTIME_CONFIG
-
-/* Battery */
-#define BATTERY_DESIRED_CHARGING_CURRENT    3500  /* mA */
-
-#define CONFIG_CHARGER_MT6370_BACKLIGHT
-
-
-/* Motion Sensors */
-#ifdef SECTION_IS_RW
-#define CONFIG_ACCELGYRO_ICM426XX
-#define CONFIG_ACCEL_INTERRUPTS
-#define CONFIG_ACCELGYRO_ICM426XX_INT_EVENT \
-	TASK_EVENT_MOTION_SENSOR_INTERRUPT(LID_ACCEL)
-
-/* Camera VSYNC */
-#define CONFIG_SYNC
-#define CONFIG_SYNC_COMMAND
-#define CONFIG_SYNC_INT_EVENT \
-	TASK_EVENT_MOTION_SENSOR_INTERRUPT(VSYNC)
-#endif /* SECTION_IS_RW */
-
-/* I2C ports */
-#define I2C_PORT_CHARGER  0
-#define I2C_PORT_TCPC0    0
-#define I2C_PORT_USB_MUX  0
-#define I2C_PORT_BATTERY  1
-#define I2C_PORT_VIRTUAL_BATTERY I2C_PORT_BATTERY
-#define I2C_PORT_ACCEL    1
-#define I2C_PORT_BC12     1
-
-/* Route sbs host requests to virtual battery driver */
-#define VIRTUAL_BATTERY_ADDR_FLAGS 0x0B
-
-/* MKBP */
-#define CONFIG_MKBP_INPUT_DEVICES
-#define CONFIG_MKBP_EVENT
-#define CONFIG_MKBP_EVENT_WAKEUP_MASK \
-	(BIT(EC_MKBP_EVENT_SENSOR_FIFO) | BIT(EC_MKBP_EVENT_HOST_EVENT))
-
-#define PD_OPERATING_POWER_MW 15000
-
-#ifndef __ASSEMBLER__
-
-enum adc_channel {
-	/* Real ADC channels begin here */
-	ADC_BOARD_ID = 0,
-	ADC_EC_SKU_ID,
-	ADC_BATT_ID,
-	ADC_POGO_ADC_INT_L,
-	ADC_CH_COUNT
-};
-
-/* power signal definitions */
-enum power_signal {
-	AP_IN_S3_L,
-	PMIC_PWR_GOOD,
-
-	/* Number of signals */
-	POWER_SIGNAL_COUNT,
-};
-
-/* Motion sensors */
-enum sensor_id {
-	LID_ACCEL = 0,
-	LID_GYRO,
-	VSYNC,
-	SENSOR_COUNT,
-};
-
-enum charge_port {
-	CHARGE_PORT_USB_C,
-};
-
-#include "gpio_signal.h"
-#include "registers.h"
-
-#ifdef SECTION_IS_RO
-/* Interrupt handler for emmc task */
-void emmc_cmd_interrupt(enum gpio_signal signal);
-#endif
-
-void board_reset_pd_mcu(void);
-int board_get_version(void);
-void pogo_adc_interrupt(enum gpio_signal signal);
-int board_discharge_on_ac(int enable);
-
-/* Enable double tap detection */
-#define CONFIG_GESTURE_DETECTION
-#define CONFIG_GESTURE_SENSOR_DOUBLE_TAP
-#define CONFIG_GESTURE_TAP_SENSOR 0
-#define CONFIG_GESTURE_SENSOR_DOUBLE_TAP_FOR_HOST
-#define CONFIG_GESTURE_SAMPLING_INTERVAL_MS 5
-#define CONFIG_GESTURE_TAP_THRES_MG 100
-#define CONFIG_GESTURE_TAP_MAX_INTERSTICE_T 500
-#define CONFIG_GESTURE_DETECTION_MASK BIT(CONFIG_GESTURE_TAP_SENSOR)
-
-#endif /* !__ASSEMBLER__ */
-
-#endif /* __CROS_EC_BOARD_H */