diff options
Diffstat (limited to 'board/metaknight/board.c')
| -rw-r--r-- | board/metaknight/board.c | 906 |
1 files changed, 0 insertions, 906 deletions
diff --git a/board/metaknight/board.c b/board/metaknight/board.c deleted file mode 100644 index 8f54536d7f..0000000000 --- a/board/metaknight/board.c +++ /dev/null @@ -1,906 +0,0 @@ -/* Copyright 2020 The Chromium OS Authors. All rights reserved. - * Use of this source code is governed by a BSD-style license that can be - * found in the LICENSE file. - */ - -/* metaknight board-specific configuration */ - -#include "adc.h" -#include "button.h" -#include "cbi_fw_config.h" -#include "cbi_ssfc.h" -#include "charge_manager.h" -#include "charge_state_v2.h" -#include "charger.h" -#include "chipset.h" -#include "common.h" -#include "compile_time_macros.h" -#include "driver/accel_bma2x2.h" -#include "driver/accel_kionix.h" -#include "driver/accelgyro_bmi_common.h" -#include "driver/accelgyro_icm_common.h" -#include "driver/accelgyro_icm426xx.h" -#include "driver/accelgyro_lsm6dsm.h" -#include "driver/temp_sensor/thermistor.h" -#include "temp_sensor.h" -#include "driver/bc12/pi3usb9201.h" -#include "driver/charger/isl923x.h" -#include "driver/retimer/nb7v904m.h" -#include "driver/tcpm/raa489000.h" -#include "driver/tcpm/tcpci.h" -#include "driver/usb_mux/pi3usb3x532.h" -#include "extpower.h" -#include "gpio.h" -#include "hooks.h" -#include "i2c.h" -#include "keyboard_scan.h" -#include "lid_switch.h" -#include "motion_sense.h" -#include "power.h" -#include "power_button.h" -#include "pwm.h" -#include "pwm_chip.h" -#include "stdbool.h" -#include "switch.h" -#include "system.h" -#include "tablet_mode.h" -#include "task.h" -#include "usb_mux.h" -#include "usb_pd.h" -#include "usb_pd_tcpm.h" - -#define CPRINTS(format, args...) cprints(CC_USBCHARGE, format, ## args) -#define CPRINTF(format, args...) cprintf(CC_USBCHARGE, format, ## args) - -#define INT_RECHECK_US 5000 - -#define ADC_VOL_UP_MASK BIT(0) -#define ADC_VOL_DOWN_MASK BIT(1) - -static uint8_t new_adc_key_state; - -/* USB-A Configuration */ -const int usb_port_enable[USB_PORT_COUNT] = { - GPIO_EN_USB_A0_VBUS, - GPIO_EN_USB_A1_VBUS, -}; - -/* C0 interrupt line shared by BC 1.2 and charger */ -static void check_c0_line(void); -DECLARE_DEFERRED(check_c0_line); - -static void notify_c0_chips(void) -{ - /* - * The interrupt line is shared between the TCPC and BC 1.2 detection - * chip. Therefore we'll need to check both ICs. - */ - schedule_deferred_pd_interrupt(0); - task_set_event(TASK_ID_USB_CHG_P0, USB_CHG_EVENT_BC12); -} - -static void check_c0_line(void) -{ - /* - * If line is still being held low, see if there's more to process from - * one of the chips - */ - if (!gpio_get_level(GPIO_USB_C0_INT_ODL)) { - notify_c0_chips(); - hook_call_deferred(&check_c0_line_data, INT_RECHECK_US); - } -} - -static void usb_c0_interrupt(enum gpio_signal s) -{ - /* Cancel any previous calls to check the interrupt line */ - hook_call_deferred(&check_c0_line_data, -1); - - /* Notify all chips using this line that an interrupt came in */ - notify_c0_chips(); - - /* Check the line again in 5ms */ - hook_call_deferred(&check_c0_line_data, INT_RECHECK_US); - -} - -static void sub_hdmi_hpd_interrupt(enum gpio_signal s) -{ - int hdmi_hpd_odl = gpio_get_level(GPIO_HDMI_HPD_SUB_ODL); - - gpio_set_level(GPIO_EC_AP_USB_C1_HDMI_HPD, !hdmi_hpd_odl); - - cprints(CC_SYSTEM, "HDMI plug-%s", !hdmi_hpd_odl ? "in" : "out"); -} - -/** - * Handle debounced pen input changing state. - */ -static void pen_input_deferred(void) -{ - int pen_charge_enable = !gpio_get_level(GPIO_PEN_DET_ODL) && - !chipset_in_state(CHIPSET_STATE_ANY_OFF); - - if (pen_charge_enable) - gpio_set_level(GPIO_EN_PP3300_PEN, 1); - else - gpio_set_level(GPIO_EN_PP3300_PEN, 0); - - CPRINTS("Pen charge %sable", pen_charge_enable ? "en" : "dis"); -} -DECLARE_DEFERRED(pen_input_deferred); - -void pen_input_interrupt(enum gpio_signal signal) -{ - /* pen input debounce time */ - hook_call_deferred(&pen_input_deferred_data, (100 * MSEC)); -} - -static void pen_charge_check(void) -{ - hook_call_deferred(&pen_input_deferred_data, (100 * MSEC)); -} -DECLARE_HOOK(HOOK_CHIPSET_STARTUP, pen_charge_check, HOOK_PRIO_LAST); -DECLARE_HOOK(HOOK_CHIPSET_SHUTDOWN, pen_charge_check, HOOK_PRIO_LAST); - -#include "gpio_list.h" - -/* ADC channels */ -const struct adc_t adc_channels[] = { - [ADC_TEMP_SENSOR_1] = { - .name = "TEMP_SENSOR1", - .input_ch = NPCX_ADC_CH0, - .factor_mul = ADC_MAX_VOLT, - .factor_div = ADC_READ_MAX + 1, - .shift = 0, - }, - [ADC_TEMP_SENSOR_2] = { - .name = "TEMP_SENSOR2", - .input_ch = NPCX_ADC_CH1, - .factor_mul = ADC_MAX_VOLT, - .factor_div = ADC_READ_MAX + 1, - .shift = 0, - }, - [ADC_SUB_ANALOG] = { - .name = "SUB_ANALOG", - .input_ch = NPCX_ADC_CH2, - .factor_mul = ADC_MAX_VOLT, - .factor_div = ADC_READ_MAX + 1, - .shift = 0, - }, - [ADC_VSNS_PP3300_A] = { - .name = "PP3300_A_PGOOD", - .input_ch = NPCX_ADC_CH9, - .factor_mul = ADC_MAX_VOLT, - .factor_div = ADC_READ_MAX + 1, - .shift = 0, - }, -}; -BUILD_ASSERT(ARRAY_SIZE(adc_channels) == ADC_CH_COUNT); - -/* Thermistors */ -const struct temp_sensor_t temp_sensors[] = { - - [TEMP_SENSOR_MEMORY] = { - .name = "Memory", - .type = TEMP_SENSOR_TYPE_BOARD, - .read = get_temp_3v3_51k1_47k_4050b, - .idx = ADC_TEMP_SENSOR_1 - }, - [TEMP_SENSOR_CPU] = { - .name = "CPU", - .type = TEMP_SENSOR_TYPE_BOARD, - .read = get_temp_3v3_51k1_47k_4050b, - .idx = ADC_TEMP_SENSOR_2 - }, -}; -BUILD_ASSERT(ARRAY_SIZE(temp_sensors) == TEMP_SENSOR_COUNT); - -const static struct ec_thermal_config thermal_memory = { - .temp_host = { - [EC_TEMP_THRESH_WARN] = 0, - [EC_TEMP_THRESH_HIGH] = C_TO_K(70), - [EC_TEMP_THRESH_HALT] = C_TO_K(85), - }, - .temp_host_release = { - [EC_TEMP_THRESH_WARN] = 0, - [EC_TEMP_THRESH_HIGH] = C_TO_K(65), - [EC_TEMP_THRESH_HALT] = 0, - }, -}; - -const static struct ec_thermal_config thermal_cpu = { - .temp_host = { - [EC_TEMP_THRESH_WARN] = 0, - [EC_TEMP_THRESH_HIGH] = C_TO_K(75), - [EC_TEMP_THRESH_HALT] = C_TO_K(80), - }, - .temp_host_release = { - [EC_TEMP_THRESH_WARN] = 0, - [EC_TEMP_THRESH_HIGH] = C_TO_K(65), - [EC_TEMP_THRESH_HALT] = 0, - }, -}; - -struct ec_thermal_config thermal_params[TEMP_SENSOR_COUNT]; - -static void setup_thermal(void) -{ - thermal_params[TEMP_SENSOR_MEMORY] = thermal_memory; - thermal_params[TEMP_SENSOR_CPU] = thermal_cpu; -} - -void board_hibernate(void) -{ - /* - * Both charger ICs need to be put into their "low power mode" before - * entering the Z-state. - */ - if (board_get_charger_chip_count() > 1) - raa489000_hibernate(1, true); - raa489000_hibernate(0, true); -} - -void board_reset_pd_mcu(void) -{ - /* - * TODO(b:147316511): Here we could issue a digital reset to the IC, - * unsure if we actually want to do that or not yet. - */ -} - -#ifdef BOARD_WADDLEDOO -static void reconfigure_5v_gpio(void) -{ - /* - * b/147257497: On early waddledoo boards, GPIO_EN_PP5000 was swapped - * with GPIO_VOLUP_BTN_ODL. Therefore, we'll actually need to set that - * GPIO instead for those boards. Note that this breaks the volume up - * button functionality. - */ - if (system_get_board_version() < 0) { - CPRINTS("old board - remapping 5V en"); - gpio_set_flags(GPIO_VOLUP_BTN_ODL, GPIO_OUT_LOW); - } -} -DECLARE_HOOK(HOOK_INIT, reconfigure_5v_gpio, HOOK_PRIO_INIT_I2C+1); -#endif /* BOARD_WADDLEDOO */ - -static void set_5v_gpio(int level) -{ - int version; - enum gpio_signal gpio = GPIO_EN_PP5000; - - /* - * b/147257497: On early waddledoo boards, GPIO_EN_PP5000 was swapped - * with GPIO_VOLUP_BTN_ODL. Therefore, we'll actually need to set that - * GPIO instead for those boards. Note that this breaks the volume up - * button functionality. - */ - if (IS_ENABLED(BOARD_WADDLEDOO)) { - version = system_get_board_version(); - - /* - * If the CBI EEPROM wasn't formatted, assume it's a very early - * board. - */ - gpio = version < 0 ? GPIO_VOLUP_BTN_ODL : GPIO_EN_PP5000; - } - - gpio_set_level(gpio, level); -} - -__override void board_power_5v_enable(int enable) -{ - /* - * Port 0 simply has a GPIO to turn on the 5V regulator, however, 5V is - * generated locally on the sub board and we need to set the comparator - * polarity on the sub board charger IC, or send enable signal to HDMI - * DB. - */ - set_5v_gpio(!!enable); - - if (get_cbi_fw_config_db() == DB_1A_HDMI || - get_cbi_fw_config_db() == DB_LTE_HDMI) { - gpio_set_level(GPIO_SUB_C1_INT_EN_RAILS_ODL, !enable); - } -} - -__override uint8_t board_get_usb_pd_port_count(void) -{ - return CONFIG_USB_PD_PORT_MAX_COUNT; -} - -__override uint8_t board_get_charger_chip_count(void) -{ - return CHARGER_NUM; -} - -int board_is_sourcing_vbus(int port) -{ - int regval; - - tcpc_read(port, TCPC_REG_POWER_STATUS, ®val); - return !!(regval & TCPC_REG_POWER_STATUS_SOURCING_VBUS); - -} - -int board_set_active_charge_port(int port) -{ - int is_real_port = (port >= 0 && - port < board_get_usb_pd_port_count()); - int i; - int old_port; - - if (!is_real_port && port != CHARGE_PORT_NONE) - return EC_ERROR_INVAL; - - old_port = charge_manager_get_active_charge_port(); - - CPRINTS("New chg p%d", port); - - /* Disable all ports. */ - if (port == CHARGE_PORT_NONE) { - for (i = 0; i < board_get_usb_pd_port_count(); i++) { - tcpc_write(i, TCPC_REG_COMMAND, - TCPC_REG_COMMAND_SNK_CTRL_LOW); - raa489000_enable_asgate(i, false); - } - - return EC_SUCCESS; - } - - /* Check if port is sourcing VBUS. */ - if (board_is_sourcing_vbus(port)) { - CPRINTS("Skip enable p%d", port); - return EC_ERROR_INVAL; - } - - /* - * Turn off the other ports' sink path FETs, before enabling the - * requested charge port. - */ - for (i = 0; i < board_get_usb_pd_port_count(); i++) { - if (i == port) - continue; - - if (tcpc_write(i, TCPC_REG_COMMAND, - TCPC_REG_COMMAND_SNK_CTRL_LOW)) - CPRINTS("p%d: sink path disable failed.", i); - raa489000_enable_asgate(i, false); - } - - /* - * Stop the charger IC from switching while changing ports. Otherwise, - * we can overcurrent the adapter we're switching to. (crbug.com/926056) - */ - if (old_port != CHARGE_PORT_NONE) - charger_discharge_on_ac(1); - - /* Enable requested charge port. */ - if (raa489000_enable_asgate(port, true) || - tcpc_write(port, TCPC_REG_COMMAND, - TCPC_REG_COMMAND_SNK_CTRL_HIGH)) { - CPRINTS("p%d: sink path enable failed.", port); - charger_discharge_on_ac(0); - return EC_ERROR_UNKNOWN; - } - - /* Allow the charger IC to begin/continue switching. */ - charger_discharge_on_ac(0); - - return EC_SUCCESS; -} - -void board_set_charge_limit(int port, int supplier, int charge_ma, - int max_ma, int charge_mv) -{ - int icl = MAX(charge_ma, CONFIG_CHARGER_INPUT_CURRENT); - - /* - * b/147463641: The charger IC seems to overdraw ~4%, therefore we - * reduce our target accordingly. - */ - icl = icl * 96 / 100; - charge_set_input_current_limit(icl, charge_mv); -} - -__override void typec_set_source_current_limit(int port, enum tcpc_rp_value rp) -{ - if (port < 0 || port > board_get_usb_pd_port_count()) - return; - - raa489000_set_output_current(port, rp); -} - -/* Sensors */ -static struct mutex g_lid_mutex; -static struct mutex g_base_mutex; - -/* Matrices to rotate accelerometers into the standard reference. */ -static const mat33_fp_t lid_standard_ref = { - { FLOAT_TO_FP(-1), 0, 0}, - { 0, FLOAT_TO_FP(-1), 0}, - { 0, 0, FLOAT_TO_FP(1)} -}; - -static const mat33_fp_t base_standard_ref = { - { 0, FLOAT_TO_FP(1), 0}, - { FLOAT_TO_FP(1), 0, 0}, - { 0, 0, FLOAT_TO_FP(-1)} -}; - -static const mat33_fp_t base_lsm6dsm_ref = { - { FLOAT_TO_FP(-1), 0, 0}, - { 0, FLOAT_TO_FP(1), 0}, - { 0, 0, FLOAT_TO_FP(-1)} -}; - -static const mat33_fp_t base_icm_ref = { - { FLOAT_TO_FP(-1), 0, 0}, - { 0, FLOAT_TO_FP(1), 0}, - { 0, 0, FLOAT_TO_FP(-1)} -}; - -static struct accelgyro_saved_data_t g_bma253_data; -static struct bmi_drv_data_t g_bmi160_data; -static struct kionix_accel_data g_kx022_data; -static struct lsm6dsm_data lsm6dsm_data = LSM6DSM_DATA; -static struct icm_drv_data_t g_icm426xx_data; - -struct motion_sensor_t motion_sensors[] = { - [LID_ACCEL] = { - .name = "Lid Accel", - .active_mask = SENSOR_ACTIVE_S0_S3, - .chip = MOTIONSENSE_CHIP_BMA255, - .type = MOTIONSENSE_TYPE_ACCEL, - .location = MOTIONSENSE_LOC_LID, - .drv = &bma2x2_accel_drv, - .mutex = &g_lid_mutex, - .drv_data = &g_bma253_data, - .port = I2C_PORT_SENSOR, - .i2c_spi_addr_flags = BMA2x2_I2C_ADDR1_FLAGS, - .rot_standard_ref = &lid_standard_ref, - .default_range = 2, - .min_frequency = BMA255_ACCEL_MIN_FREQ, - .max_frequency = BMA255_ACCEL_MAX_FREQ, - .config = { - [SENSOR_CONFIG_EC_S0] = { - .odr = 10000 | ROUND_UP_FLAG, - }, - [SENSOR_CONFIG_EC_S3] = { - .odr = 10000 | ROUND_UP_FLAG, - }, - }, - }, - [BASE_ACCEL] = { - .name = "Base Accel", - .active_mask = SENSOR_ACTIVE_S0_S3, - .chip = MOTIONSENSE_CHIP_BMI160, - .type = MOTIONSENSE_TYPE_ACCEL, - .location = MOTIONSENSE_LOC_BASE, - .drv = &bmi160_drv, - .mutex = &g_base_mutex, - .drv_data = &g_bmi160_data, - .port = I2C_PORT_SENSOR, - .i2c_spi_addr_flags = BMI160_ADDR0_FLAGS, - .rot_standard_ref = &base_standard_ref, - .default_range = 4, - .min_frequency = BMI_ACCEL_MIN_FREQ, - .max_frequency = BMI_ACCEL_MAX_FREQ, - .config = { - [SENSOR_CONFIG_EC_S0] = { - .odr = 13000 | ROUND_UP_FLAG, - .ec_rate = 100 * MSEC, - }, - [SENSOR_CONFIG_EC_S3] = { - .odr = 10000 | ROUND_UP_FLAG, - .ec_rate = 100 * MSEC, - }, - }, - }, - [BASE_GYRO] = { - .name = "Base Gyro", - .active_mask = SENSOR_ACTIVE_S0_S3, - .chip = MOTIONSENSE_CHIP_BMI160, - .type = MOTIONSENSE_TYPE_GYRO, - .location = MOTIONSENSE_LOC_BASE, - .drv = &bmi160_drv, - .mutex = &g_base_mutex, - .drv_data = &g_bmi160_data, - .port = I2C_PORT_SENSOR, - .i2c_spi_addr_flags = BMI160_ADDR0_FLAGS, - .default_range = 1000, /* dps */ - .rot_standard_ref = &base_standard_ref, - .min_frequency = BMI_GYRO_MIN_FREQ, - .max_frequency = BMI_GYRO_MAX_FREQ, - }, -}; - -const unsigned int motion_sensor_count = ARRAY_SIZE(motion_sensors); - -struct motion_sensor_t kx022_lid_accel = { - .name = "Lid Accel", - .active_mask = SENSOR_ACTIVE_S0_S3, - .chip = MOTIONSENSE_CHIP_KX022, - .type = MOTIONSENSE_TYPE_ACCEL, - .location = MOTIONSENSE_LOC_LID, - .drv = &kionix_accel_drv, - .mutex = &g_lid_mutex, - .drv_data = &g_kx022_data, - .port = I2C_PORT_ACCEL, - .i2c_spi_addr_flags = KX022_ADDR0_FLAGS, - .rot_standard_ref = &lid_standard_ref, - .min_frequency = KX022_ACCEL_MIN_FREQ, - .max_frequency = KX022_ACCEL_MAX_FREQ, - .default_range = 2, /* g, to support tablet mode */ - .config = { - /* EC use accel for angle detection */ - [SENSOR_CONFIG_EC_S0] = { - .odr = 10000 | ROUND_UP_FLAG, - }, - /* EC use accel for angle detection */ - [SENSOR_CONFIG_EC_S3] = { - .odr = 10000 | ROUND_UP_FLAG, - }, - }, -}; - -struct motion_sensor_t lsm6dsm_base_accel = { - .name = "Base Accel", - .active_mask = SENSOR_ACTIVE_S0_S3, - .chip = MOTIONSENSE_CHIP_LSM6DS3, - .type = MOTIONSENSE_TYPE_ACCEL, - .location = MOTIONSENSE_LOC_BASE, - .drv = &lsm6dsm_drv, - .mutex = &g_base_mutex, - .drv_data = LSM6DSM_ST_DATA(lsm6dsm_data, - MOTIONSENSE_TYPE_ACCEL), - .int_signal = GPIO_BASE_SIXAXIS_INT_L, - .flags = MOTIONSENSE_FLAG_INT_SIGNAL, - .port = I2C_PORT_SENSOR, - .i2c_spi_addr_flags = LSM6DSM_ADDR0_FLAGS, - .rot_standard_ref = &base_lsm6dsm_ref, - .default_range = 4, /* g */ - .min_frequency = LSM6DSM_ODR_MIN_VAL, - .max_frequency = LSM6DSM_ODR_MAX_VAL, - .config = { - [SENSOR_CONFIG_EC_S0] = { - .odr = 13000 | ROUND_UP_FLAG, - .ec_rate = 100 * MSEC, - }, - [SENSOR_CONFIG_EC_S3] = { - .odr = 10000 | ROUND_UP_FLAG, - .ec_rate = 100 * MSEC, - }, - }, -}; - -struct motion_sensor_t lsm6dsm_base_gyro = { - .name = "Base Gyro", - .active_mask = SENSOR_ACTIVE_S0_S3, - .chip = MOTIONSENSE_CHIP_LSM6DS3, - .type = MOTIONSENSE_TYPE_GYRO, - .location = MOTIONSENSE_LOC_BASE, - .drv = &lsm6dsm_drv, - .mutex = &g_base_mutex, - .drv_data = LSM6DSM_ST_DATA(lsm6dsm_data, - MOTIONSENSE_TYPE_GYRO), - .int_signal = GPIO_BASE_SIXAXIS_INT_L, - .flags = MOTIONSENSE_FLAG_INT_SIGNAL, - .port = I2C_PORT_SENSOR, - .i2c_spi_addr_flags = LSM6DSM_ADDR0_FLAGS, - .default_range = 1000 | ROUND_UP_FLAG, /* dps */ - .rot_standard_ref = &base_lsm6dsm_ref, - .min_frequency = LSM6DSM_ODR_MIN_VAL, - .max_frequency = LSM6DSM_ODR_MAX_VAL, -}; - - -struct motion_sensor_t icm426xx_base_accel = { - .name = "Base Accel", - .active_mask = SENSOR_ACTIVE_S0_S3, - .chip = MOTIONSENSE_CHIP_ICM426XX, - .type = MOTIONSENSE_TYPE_ACCEL, - .location = MOTIONSENSE_LOC_BASE, - .drv = &icm426xx_drv, - .mutex = &g_base_mutex, - .drv_data = &g_icm426xx_data, - .port = I2C_PORT_ACCEL, - .i2c_spi_addr_flags = ICM426XX_ADDR0_FLAGS, - .default_range = 4, /* g, enough for laptop */ - .rot_standard_ref = &base_icm_ref, - .min_frequency = ICM426XX_ACCEL_MIN_FREQ, - .max_frequency = ICM426XX_ACCEL_MAX_FREQ, - .config = { - /* EC use accel for angle detection */ - [SENSOR_CONFIG_EC_S0] = { - .odr = 13000 | ROUND_UP_FLAG, - .ec_rate = 100 * MSEC, - }, - /* EC use accel for angle detection */ - [SENSOR_CONFIG_EC_S3] = { - .odr = 10000 | ROUND_UP_FLAG, - .ec_rate = 100 * MSEC, - }, - }, -}; - -struct motion_sensor_t icm426xx_base_gyro = { - .name = "Base Gyro", - .active_mask = SENSOR_ACTIVE_S0_S3, - .chip = MOTIONSENSE_CHIP_ICM426XX, - .type = MOTIONSENSE_TYPE_GYRO, - .location = MOTIONSENSE_LOC_BASE, - .drv = &icm426xx_drv, - .mutex = &g_base_mutex, - .drv_data = &g_icm426xx_data, - .port = I2C_PORT_ACCEL, - .i2c_spi_addr_flags = ICM426XX_ADDR0_FLAGS, - .default_range = 1000, /* dps */ - .rot_standard_ref = &base_icm_ref, - .min_frequency = ICM426XX_GYRO_MIN_FREQ, - .max_frequency = ICM426XX_GYRO_MAX_FREQ, -}; - -static int base_gyro_config; - -void board_init(void) -{ - int on; - - gpio_enable_interrupt(GPIO_USB_C0_INT_ODL); - check_c0_line(); - - if (get_cbi_fw_config_db() == DB_1A_HDMI || - get_cbi_fw_config_db() == DB_LTE_HDMI) { - /* Disable i2c on HDMI pins */ - gpio_config_pin(MODULE_I2C, GPIO_HDMI_HPD_SUB_ODL, 0); - gpio_config_pin(MODULE_I2C, GPIO_GPIO92_NC, 0); - - gpio_set_flags(GPIO_SUB_C1_INT_EN_RAILS_ODL, GPIO_ODR_HIGH); - - /* Select HDMI option */ - gpio_set_level(GPIO_HDMI_SEL_L, 0); - - /* Enable interrupt for passing through HPD */ - gpio_enable_interrupt(GPIO_HDMI_HPD_SUB_ODL); - } else { - /* Set SDA as an input */ - gpio_set_flags(GPIO_HDMI_HPD_SUB_ODL, - GPIO_INPUT); - } - /* Enable gpio interrupt for base accelgyro sensor */ - gpio_enable_interrupt(GPIO_BASE_SIXAXIS_INT_L); - - /* Enable gpio interrupt for pen detect */ - gpio_enable_interrupt(GPIO_PEN_DET_ODL); - - /* Turn on 5V if the system is on, otherwise turn it off. */ - on = chipset_in_state(CHIPSET_STATE_ON | CHIPSET_STATE_ANY_SUSPEND | - CHIPSET_STATE_SOFT_OFF); - board_power_5v_enable(on); - - /* Initialize g-sensor */ - base_gyro_config = get_cbi_ssfc_base_sensor(); - - if (base_gyro_config == SSFC_SENSOR_LSM6DSM) { - motion_sensors[BASE_ACCEL] = lsm6dsm_base_accel; - motion_sensors[BASE_GYRO] = lsm6dsm_base_gyro; - cprints(CC_SYSTEM, "SSFC: BASE GYRO is LSM6DSM"); - } else if (get_cbi_ssfc_base_sensor() == SSFC_SENSOR_ICM426XX) { - motion_sensors[BASE_ACCEL] = icm426xx_base_accel; - motion_sensors[BASE_GYRO] = icm426xx_base_gyro; - cprints(CC_SYSTEM, "SSFC: BASE GYRO is ICM426XX"); - } else - cprints(CC_SYSTEM, "SSFC: BASE GYRO is BMI160"); - - if (get_cbi_ssfc_lid_sensor() == SSFC_SENSOR_KX022) { - motion_sensors[LID_ACCEL] = kx022_lid_accel; - cprints(CC_SYSTEM, "SSFC: LID ACCEL is KX022"); - } else - cprints(CC_SYSTEM, "SSFC: LID ACCEL is BMA253"); - - /* Initial thermal */ - setup_thermal(); - -} -DECLARE_HOOK(HOOK_INIT, board_init, HOOK_PRIO_DEFAULT); - -int pd_snk_is_vbus_provided(int port) -{ - return pd_check_vbus_level(port, VBUS_PRESENT); -} - -const struct charger_config_t chg_chips[] = { - { - .i2c_port = I2C_PORT_USB_C0, - .i2c_addr_flags = ISL923X_ADDR_FLAGS, - .drv = &isl923x_drv, - }, -}; - -const struct pi3usb9201_config_t pi3usb9201_bc12_chips[] = { - { - .i2c_port = I2C_PORT_USB_C0, - .i2c_addr_flags = PI3USB9201_I2C_ADDR_3_FLAGS, - .flags = PI3USB9201_ALWAYS_POWERED, - }, -}; - -const struct tcpc_config_t tcpc_config[CONFIG_USB_PD_PORT_MAX_COUNT] = { - { - .bus_type = EC_BUS_TYPE_I2C, - .i2c_info = { - .port = I2C_PORT_USB_C0, - .addr_flags = RAA489000_TCPC0_I2C_FLAGS, - }, - .flags = TCPC_FLAGS_TCPCI_REV2_0, - .drv = &raa489000_tcpm_drv, - }, -}; - -const struct usb_mux usb_muxes[CONFIG_USB_PD_PORT_MAX_COUNT] = { - { - .usb_port = 0, - .i2c_port = I2C_PORT_USB_C0, - .i2c_addr_flags = PI3USB3X532_I2C_ADDR0, - .driver = &pi3usb3x532_usb_mux_driver, - }, -}; - -uint16_t tcpc_get_alert_status(void) -{ - uint16_t status = 0; - int regval; - - /* - * The interrupt line is shared between the TCPC and BC1.2 detector IC. - * Therefore, go out and actually read the alert registers to report the - * alert status. - */ - if (!gpio_get_level(GPIO_USB_C0_INT_ODL)) { - if (!tcpc_read16(0, TCPC_REG_ALERT, ®val)) { - /* The TCPCI Rev 1.0 spec says to ignore bits 14:12. */ - if (!(tcpc_config[0].flags & TCPC_FLAGS_TCPCI_REV2_0)) - regval &= ~((1 << 14) | (1 << 13) | (1 << 12)); - - if (regval) - status |= PD_STATUS_TCPC_ALERT_0; - } - } - - if (board_get_usb_pd_port_count() > 1 && - !gpio_get_level(GPIO_SUB_C1_INT_EN_RAILS_ODL)) { - if (!tcpc_read16(1, TCPC_REG_ALERT, ®val)) { - /* TCPCI spec Rev 1.0 says to ignore bits 14:12. */ - if (!(tcpc_config[1].flags & TCPC_FLAGS_TCPCI_REV2_0)) - regval &= ~((1 << 14) | (1 << 13) | (1 << 12)); - - if (regval) - status |= PD_STATUS_TCPC_ALERT_1; - } - } - - return status; -} - -int adc_to_physical_value(enum gpio_signal gpio) -{ - if (gpio == GPIO_VOLUME_UP_L) - return !!(new_adc_key_state & ADC_VOL_UP_MASK); - else if (gpio == GPIO_VOLUME_DOWN_L) - return !!(new_adc_key_state & ADC_VOL_DOWN_MASK); - - CPRINTS("Not a volume up or down key"); - return 0; -} - -int button_is_adc_detected(enum gpio_signal gpio) -{ - return (gpio == GPIO_VOLUME_DOWN_L) || (gpio == GPIO_VOLUME_UP_L); -} - -static void adc_vol_key_press_check(void) -{ - int volt = adc_read_channel(ADC_SUB_ANALOG); - static uint8_t old_adc_key_state; - uint8_t adc_key_state_change; - - if (volt > 2400 && volt < 2540) { - /* volume-up is pressed */ - new_adc_key_state = ADC_VOL_UP_MASK; - } else if (volt > 2600 && volt < 2740) { - /* volume-down is pressed */ - new_adc_key_state = ADC_VOL_DOWN_MASK; - } else if (volt < 2300) { - /* both volumn-up and volume-down are pressed */ - new_adc_key_state = ADC_VOL_UP_MASK | ADC_VOL_DOWN_MASK; - } else if (volt > 2780) { - /* both volumn-up and volume-down are released */ - new_adc_key_state = 0; - } - if (new_adc_key_state != old_adc_key_state) { - adc_key_state_change = old_adc_key_state ^ new_adc_key_state; - if (adc_key_state_change && ADC_VOL_UP_MASK) - button_interrupt(GPIO_VOLUME_UP_L); - if (adc_key_state_change && ADC_VOL_DOWN_MASK) - button_interrupt(GPIO_VOLUME_DOWN_L); - - old_adc_key_state = new_adc_key_state; - } -} -DECLARE_HOOK(HOOK_TICK, adc_vol_key_press_check, HOOK_PRIO_DEFAULT); - -/* This callback disables keyboard when convertibles are fully open */ -__override void lid_angle_peripheral_enable(int enable) -{ - int chipset_in_s0 = chipset_in_state(CHIPSET_STATE_ON); - - /* - * If the lid is in tablet position via other sensors, - * ignore the lid angle, which might be faulty then - * disable keyboard. - */ - if (tablet_get_mode()) - enable = 0; - - if (enable) { - keyboard_scan_enable(1, KB_SCAN_DISABLE_LID_ANGLE); - } else { - /* - * Ensure that the chipset is off before disabling the keyboard. - * When the chipset is on, the EC keeps the keyboard enabled and - * the AP decides whether to ignore input devices or not. - */ - if (!chipset_in_s0) - keyboard_scan_enable(0, KB_SCAN_DISABLE_LID_ANGLE); - } -} - -#ifndef TEST_BUILD -void motion_interrupt(enum gpio_signal signal) -{ - switch (base_gyro_config) { - case SSFC_SENSOR_LSM6DSM: - lsm6dsm_interrupt(signal); - break; - case SSFC_SENSOR_ICM426XX: - icm426xx_interrupt(signal); - break; - case SSFC_SENSOR_BMI160: - default: - bmi160_interrupt(signal); - break; - } -} - -const struct i2c_port_t i2c_ports[] = { - { - "eeprom", I2C_PORT_EEPROM, 400, GPIO_EC_I2C_EEPROM_SCL, - GPIO_EC_I2C_EEPROM_SDA - }, - - { - "battery", I2C_PORT_BATTERY, 100, GPIO_EC_I2C_BATTERY_SCL, - GPIO_EC_I2C_BATTERY_SDA - }, - - { - "sensor", I2C_PORT_SENSOR, 400, GPIO_EC_I2C_SENSOR_SCL, - GPIO_EC_I2C_SENSOR_SDA - }, - - { - "usbc0", I2C_PORT_USB_C0, 1000, GPIO_EC_I2C_USB_C0_SCL, - GPIO_EC_I2C_USB_C0_SDA - }, -#if CONFIG_USB_PD_PORT_MAX_COUNT > 1 - { - "sub_usbc1", I2C_PORT_SUB_USB_C1, 1000, - GPIO_EC_I2C_SUB_USB_C1_SCL, GPIO_EC_I2C_SUB_USB_C1_SDA - }, -#endif -}; - -#endif |