diff options
Diffstat (limited to 'board/nocturne/board.h')
| -rw-r--r-- | board/nocturne/board.h | 280 |
1 files changed, 0 insertions, 280 deletions
diff --git a/board/nocturne/board.h b/board/nocturne/board.h deleted file mode 100644 index 95f8d14403..0000000000 --- a/board/nocturne/board.h +++ /dev/null @@ -1,280 +0,0 @@ -/* Copyright 2018 The Chromium OS Authors. All rights reserved. - * Use of this source code is governed by a BSD-style license that can be - * found in the LICENSE file. - */ - -/* Nocturne board configuration */ - -#ifndef __CROS_EC_BOARD_H -#define __CROS_EC_BOARD_H - -/* - * By default, enable all console messages excepted HC, ACPI and event: - * The sensor stack is generating a lot of activity. - */ -#define CC_DEFAULT (CC_ALL & ~(CC_MASK(CC_EVENTS) | CC_MASK(CC_LPC))) -#undef CONFIG_HOSTCMD_DEBUG_MODE -#define CONFIG_HOSTCMD_DEBUG_MODE HCDEBUG_OFF - -/* NPCX7 config */ -#define NPCX_UART_MODULE2 1 /* GPIO64/65 are used as UART pins. */ -#define NPCX_TACH_SEL2 0 /* No tach. */ -#define NPCX7_PWM1_SEL 0 /* GPIO C2 is not used as PWM1. */ -#define CONFIG_HIBERNATE_PSL - -/* Internal SPI flash on NPCX7 */ -#define CONFIG_FLASH_SIZE_BYTES (512 * 1024) /* It's really 1MB. */ -#define CONFIG_SPI_FLASH_REGS -#define CONFIG_SPI_FLASH_W25Q80 /* Internal SPI flash type. */ - -/* EC modules */ -#define CONFIG_ADC -#define CONFIG_BACKLIGHT_LID -#define CONFIG_HOSTCMD_ESPI -#define CONFIG_I2C -#define CONFIG_I2C_BUS_MAY_BE_UNPOWERED -#define CONFIG_I2C_CONTROLLER -#define CONFIG_LOW_POWER_IDLE -#define CONFIG_PWM -#define CONFIG_THROTTLE_AP -#define CONFIG_VBOOT_HASH -#define CONFIG_VSTORE -#define CONFIG_VSTORE_SLOT_COUNT 1 - -#define CONFIG_DETACHABLE_BASE - -/* EC console commands */ -#define CONFIG_CMD_ACCELS -#define CONFIG_CMD_ACCEL_INFO -#define CONFIG_CMD_BUTTON -#define CONFIG_CMD_CHARGEN -#define CONFIG_HOSTCMD_PD_CONTROL -#define CONFIG_CMD_PPC_DUMP - -/* Battery */ -#define CONFIG_BATTERY_CUT_OFF -#define CONFIG_BATTERY_SMART -#define CONFIG_BATTERY_REVIVE_DISCONNECT -#define CONFIG_BATTERY_PRESENT_GPIO GPIO_BAT_PRESENT_L -#define CONFIG_BATT_FULL_CHIPSET_OFF_INPUT_LIMIT_MV 9000 - -/* Buttons / Switches */ -#define CONFIG_BASE_ATTACHED_SWITCH -#define CONFIG_BUTTON_TRIGGERED_RECOVERY -#define CONFIG_VOLUME_BUTTONS - -/* Charger */ -#define CONFIG_CHARGE_MANAGER -#define CONFIG_CHARGER -#define CONFIG_CHARGER_DISCHARGE_ON_AC -#define CONFIG_CHARGER_INPUT_CURRENT 128 -#define CONFIG_CHARGER_ISL9238 -#undef CONFIG_CHARGER_MIN_BAT_PCT_FOR_POWER_ON -#define CONFIG_CHARGER_MIN_BAT_PCT_FOR_POWER_ON 1 -#define CONFIG_CHARGER_PROFILE_OVERRIDE -#define CONFIG_CHARGER_SENSE_RESISTOR 10 -#define CONFIG_CHARGER_SENSE_RESISTOR_AC 20 -#define CONFIG_EXTPOWER_GPIO - -/* LEDs */ -#define CONFIG_LED_COMMON -#define CONFIG_LED_PWM_ACTIVE_CHARGE_PORT_ONLY -#define CONFIG_LED_PWM_COUNT 2 -#undef CONFIG_LED_PWM_NEAR_FULL_COLOR -#define CONFIG_LED_PWM_NEAR_FULL_COLOR EC_LED_COLOR_WHITE - -/* MKBP */ -#define CONFIG_MKBP_EVENT -#define CONFIG_MKBP_EVENT_WAKEUP_MASK (1<<EC_MKBP_EVENT_SWITCH) -#define CONFIG_MKBP_INPUT_DEVICES -#define CONFIG_MKBP_USE_GPIO_AND_HOST_EVENT - -/* Sensors */ -#define CONFIG_ALS -#define ALS_COUNT 1 -#define CONFIG_ALS_OPT3001 -#define OPT3001_I2C_ADDR_FLAGS OPT3001_I2C_ADDR1_FLAGS -/* Enable sensor fifo, must also define the _SIZE and _THRES */ -#define CONFIG_ACCEL_FIFO -/* Must be a power of 2 */ -#define CONFIG_ACCEL_FIFO_SIZE 512 -/* Depends on how fast the AP boots and typical ODRs */ -#define CONFIG_ACCEL_FIFO_THRES (CONFIG_ACCEL_FIFO_SIZE / 3) -#define CONFIG_ACCEL_INTERRUPTS -#define CONFIG_ACCELGYRO_BMI160 -#define CONFIG_ACCELGYRO_BMI160_INT_EVENT \ - TASK_EVENT_MOTION_SENSOR_INTERRUPT(LID_ACCEL) -#define CONFIG_SYNC -#define CONFIG_SYNC_INT_EVENT \ - TASK_EVENT_MOTION_SENSOR_INTERRUPT(VSYNC) -#define CONFIG_TEMP_SENSOR -#define CONFIG_TEMP_SENSOR_BD99992GW -#define CONFIG_THERMISTOR_NCP15WB - -/* SoC */ -#define CONFIG_BOARD_HAS_RTC_RESET -#define CONFIG_CHIPSET_CAN_THROTTLE -#define CONFIG_CHIPSET_SKYLAKE -#define CONFIG_CHIPSET_HAS_PLATFORM_PMIC_RESET -#define CONFIG_CHIPSET_RESET_HOOK -#define CONFIG_CPU_PROCHOT_ACTIVE_LOW -#define CONFIG_DPTF -#define CONFIG_DO_NOT_INCLUDE_RV32I_PANIC_DATA -#define CONFIG_POWER_COMMON -#define CONFIG_POWER_BUTTON -#define CONFIG_POWER_BUTTON_X86 -#define CONFIG_POWER_S0IX -#define CONFIG_POWER_TRACK_HOST_SLEEP_STATE - -#define CONFIG_USB_PID 0x5045 - -/* USB PD */ -#define CONFIG_USB_DRP_ACC_TRYSRC -#define CONFIG_USB_PD_3A_PORTS 0 -#define CONFIG_USB_PD_ALT_MODE -#define CONFIG_USB_PD_ALT_MODE_DFP -#define CONFIG_USB_PD_COMM_LOCKED -#define CONFIG_USB_PD_DECODE_SOP -#define CONFIG_USB_PD_DISCHARGE_PPC -#define CONFIG_USB_PD_DP_HPD_GPIO -#define CONFIG_USB_PD_DUAL_ROLE -#define CONFIG_USB_PD_DUAL_ROLE_AUTO_TOGGLE -#define CONFIG_USB_PD_LOGGING -#define CONFIG_USB_PD_PORT_MAX_COUNT 2 -#define CONFIG_USB_PD_TCPC_LOW_POWER -#define CONFIG_USB_PD_REV30 -#define CONFIG_USB_PD_TCPMV2 -#define CONFIG_USB_PD_TCPM_MUX -#define CONFIG_USB_PD_TCPM_PS8805 -#define CONFIG_USB_PD_TCPM_TCPCI -#define CONFIG_USB_PD_TRY_SRC -#define CONFIG_USB_PD_VBUS_DETECT_TCPC -#define CONFIG_USB_PD_VBUS_MEASURE_NOT_PRESENT -#define CONFIG_USB_PE_SM -#define CONFIG_USB_POWER_DELIVERY -#define CONFIG_USB_PRL_SM -#define CONFIG_USB_TYPEC_SM -#define CONFIG_USBC_PPC_SN5S330 -#define CONFIG_USBC_SS_MUX -#define CONFIG_USBC_SS_MUX_DFP_ONLY -#define CONFIG_USBC_VCONN -#define CONFIG_USBC_VCONN_SWAP - -/* Define typical operating power and max power. */ -#define PD_MAX_VOLTAGE_MV 20000 -#define PD_MAX_CURRENT_MA 3000 -#define PD_MAX_POWER_MW 45000 -#define PD_OPERATING_POWER_MW 15000 - -/* TODO(aaboagye): Verify these timings. */ -/* - * delay to turn on the power supply max is ~16ms. - * delay to turn off the power supply max is about ~180ms. - */ -#define PD_POWER_SUPPLY_TURN_ON_DELAY 30000 /* us */ -#define PD_POWER_SUPPLY_TURN_OFF_DELAY 250000 /* us */ - -/* I2C config */ -#define I2C_PORT_CHARGER I2C_PORT_POWER -#define I2C_PORT_PMIC I2C_PORT_POWER -#define I2C_PORT_POWER NPCX_I2C_PORT0_0 -#define I2C_PORT_BATTERY NPCX_I2C_PORT4_1 -#define I2C_PORT_ALS_GYRO NPCX_I2C_PORT5_0 -#define I2C_PORT_ACCEL I2C_PORT_ALS_GYRO -#define I2C_PORT_USB_C0 NPCX_I2C_PORT1_0 -#define I2C_PORT_USB_C1 NPCX_I2C_PORT2_0 -#define I2C_PORT_THERMAL I2C_PORT_PMIC - -#define GPIO_USB_C0_SCL GPIO_EC_I2C1_USB_C0_SCL -#define GPIO_USB_C0_SDA GPIO_EC_I2C1_USB_C0_SDA -#define GPIO_USB_C1_SCL GPIO_EC_I2C2_USB_C1_SCL -#define GPIO_USB_C1_SDA GPIO_EC_I2C2_USB_C1_SDA - -#define I2C_ADDR_MP2949_FLAGS 0x20 -#define I2C_ADDR_BD99992_FLAGS 0x30 - -/* - * Remapping of schematic GPIO names to common GPIO names expected (hardcoded) - * in the EC code base. - */ -#define GPIO_AC_PRESENT GPIO_ACOK_OD -#define GPIO_ENABLE_BACKLIGHT GPIO_EC_BL_DISABLE_ODL -#define GPIO_BAT_PRESENT_L GPIO_EC_BATT_PRES_L -#define GPIO_ENTERING_RW GPIO_EC_ENTERING_RW -#define GPIO_PCH_PWRBTN_L GPIO_EC_PCH_PWR_BTN_L -#define GPIO_PCH_RSMRST_L GPIO_RSMRST_L -#define GPIO_PCH_RTCRST GPIO_EC_PCH_RTCRST -#define GPIO_PCH_SLP_S0_L GPIO_SLP_S0_L -#define GPIO_PCH_SLP_S3_L GPIO_SLP_S3_L -#define GPIO_PCH_SLP_S4_L GPIO_SLP_S4_L -#define GPIO_PCH_SLP_SUS_L GPIO_SLP_SUS_L_PCH -#define GPIO_PCH_WAKE_L GPIO_EC_PCH_WAKE_L -#define GPIO_PMIC_DPWROK GPIO_ROP_DSW_PWROK_EC -#define GPIO_PMIC_SLP_SUS_L GPIO_SLP_SUS_L_PMIC -#define GPIO_POWER_BUTTON_L GPIO_EC_PWR_BTN_IN_ODL -#define GPIO_CPU_PROCHOT GPIO_EC_PROCHOT_ODL -#define GPIO_RSMRST_L_PGOOD GPIO_ROP_EC_RSMRST_L -#define GPIO_VOLUME_UP_L GPIO_H1_EC_VOL_UP_ODL -#define GPIO_VOLUME_DOWN_L GPIO_H1_EC_VOL_DOWN_ODL -#define GPIO_WP_L GPIO_EC_WP_L - -#define PORT_TO_HPD(port) ((port) ? GPIO_USB_C1_DP_HPD : GPIO_USB_C0_DP_HPD) - -#ifndef __ASSEMBLER__ - -#include "gpio_signal.h" -#include "registers.h" - -/* ADC signal */ -enum adc_channel { - ADC_BASE_ATTACH, - ADC_BASE_DETACH, - ADC_CH_COUNT -}; - -enum temp_sensor_id { - TEMP_SENSOR_BATTERY, /* BD99956GW TSENSE */ - TEMP_SENSOR_AMBIENT, /* BD99992GW SYSTHERM0 */ - TEMP_SENSOR_CHARGER, /* BD99992GW SYSTHERM1 */ - TEMP_SENSOR_DRAM, /* BD99992GW SYSTHERM2 */ - TEMP_SENSOR_EMMC, /* BD99992GW SYSTHERM3 */ - TEMP_SENSOR_GYRO, /* BMI160 */ - TEMP_SENSOR_COUNT -}; - -enum pwm_channel { - PWM_CH_DB0_LED_RED = 0, - PWM_CH_DB0_LED_GREEN, - PWM_CH_DB0_LED_BLUE, - PWM_CH_DB1_LED_RED, - PWM_CH_DB1_LED_GREEN, - PWM_CH_DB1_LED_BLUE, - PWM_CH_COUNT -}; - -/* - * Motion sensors: - * When reading through IO memory is set up for sensors (LPC is used), - * the first 2 entries must be accelerometers, then gyroscope. - * For BMI160, accel and gyro sensors must be next to each other. - */ -enum sensor_id { - LID_ACCEL, - LID_GYRO, - LID_ALS, - VSYNC, - SENSOR_COUNT, -}; - -#define CONFIG_ACCEL_FORCE_MODE_MASK BIT(LID_ALS) - -void base_pwr_fault_interrupt(enum gpio_signal s); -int board_get_version(void); - -/* Reset all TCPCs. */ -void board_reset_pd_mcu(void); -void board_set_tcpc_power_mode(int port, int mode); - -#endif /* __ASSEMBLER__ */ - -#endif /* __CROS_EC_BOARD_H */ |