1 files changed, 0 insertions, 124 deletions
diff --git a/board/nucleo-f411re/board.c b/board/nucleo-f411re/board.c
deleted file mode 100644
index a177a793ab..0000000000
--- a/board/nucleo-f411re/board.c
+++ /dev/null
@@ -1,124 +0,0 @@
-/* Copyright 2015 The Chromium OS Authors. All rights reserved.
- * Use of this source code is governed by a BSD-style license that can be
- * found in the LICENSE file.
- */
-/* nucleo-f411re development board configuration */
-
-#include "adc.h"
-#include "common.h"
-#include "console.h"
-#include "driver/accelgyro_bmi_common.h"
-#include "ec_version.h"
-#include "gpio.h"
-#include "hooks.h"
-#include "i2c.h"
-#include "motion_sense.h"
-
-#include "gpio.h"
-#include "registers.h"
-#include "task.h"
-#include "util.h"
-
-void user_button_evt(enum gpio_signal signal)
-{
-	ccprintf("Button %d, %d!\n", signal, gpio_get_level(signal));
-}
-
-#include "gpio_list.h"
-
-/* Initialize board. */
-static void board_init(void)
-{
-	gpio_enable_interrupt(GPIO_USER_BUTTON_L);
-
-	/* No power control yet */
-	/* Go to S3 state */
-	hook_notify(HOOK_CHIPSET_STARTUP);
-
-	/* Go to S0 state */
-	hook_notify(HOOK_CHIPSET_RESUME);
-}
-DECLARE_HOOK(HOOK_INIT, board_init, HOOK_PRIO_DEFAULT);
-
-/* ADC channels */
-const struct adc_t adc_channels[] = {
-	/* Arduino connectors analog pins */
-	[ADC1_0] = {"ADC1_0",  3000, 4096, 0, STM32_AIN(0)},
-	[ADC1_1] = {"ADC1_1",  3000, 4096, 0, STM32_AIN(1)},
-	[ADC1_4] = {"ADC1_4",  3000, 4096, 0, STM32_AIN(4)},
-	[ADC1_8] = {"ADC1_8",  3000, 4096, 0, STM32_AIN(8)},
-};
-BUILD_ASSERT(ARRAY_SIZE(adc_channels) == ADC_CH_COUNT);
-
-/* I2C ports */
-const struct i2c_port_t i2c_ports[] = {
-	{"master", I2C_PORT_MASTER, 100,
-	 GPIO_MASTER_I2C_SCL, GPIO_MASTER_I2C_SDA},
-};
-
-const unsigned int i2c_ports_used = ARRAY_SIZE(i2c_ports);
-
-/* Base Sensor mutex */
-static struct mutex g_base_mutex;
-
-static struct bmi_drv_data_t g_bmi160_data;
-
-struct motion_sensor_t motion_sensors[] = {
-	[BASE_ACCEL] = {
-	 .name = "Base Accel",
-	 .active_mask = SENSOR_ACTIVE_S0_S3,
-	 .chip = MOTIONSENSE_CHIP_BMI160,
-	 .type = MOTIONSENSE_TYPE_ACCEL,
-	 .location = MOTIONSENSE_LOC_BASE,
-	 .drv = &bmi160_drv,
-	 .mutex = &g_base_mutex,
-	 .drv_data = &g_bmi160_data,
-	 .port = I2C_PORT_ACCEL,
-	 .i2c_spi_addr_flags = BMI160_ADDR0_FLAGS,
-	 .default_range = 4,  /* g, to meet CDD 7.3.1/C-1-4 reqs */
-	 .min_frequency = BMI_ACCEL_MIN_FREQ,
-	 .max_frequency = BMI_ACCEL_MAX_FREQ,
-	 .config = {
-		 /* EC use accel for angle detection */
-		 [SENSOR_CONFIG_EC_S0] = {
-			.odr = 10000 | ROUND_UP_FLAG,
-			.ec_rate = 100 * MSEC,
-		 },
-		 /* Sensor on for lid angle detection */
-		 [SENSOR_CONFIG_EC_S3] = {
-			.odr = 10000 | ROUND_UP_FLAG,
-			.ec_rate = 100 * MSEC,
-		 },
-	 },
-	},
-
-	[BASE_GYRO] = {
-	 .name = "Base Gyro",
-	 .active_mask = SENSOR_ACTIVE_S0_S3,
-	 .chip = MOTIONSENSE_CHIP_BMI160,
-	 .type = MOTIONSENSE_TYPE_GYRO,
-	 .location = MOTIONSENSE_LOC_BASE,
-	 .drv = &bmi160_drv,
-	 .mutex = &g_base_mutex,
-	 .drv_data = &g_bmi160_data,
-	 .port = I2C_PORT_ACCEL,
-	 .i2c_spi_addr_flags = BMI160_ADDR0_FLAGS,
-	 .default_range = 1000, /* dps */
-	 .min_frequency = BMI_GYRO_MIN_FREQ,
-	 .max_frequency = BMI_GYRO_MAX_FREQ,
-	},
-};
-const unsigned int motion_sensor_count = ARRAY_SIZE(motion_sensors);
-
-#ifdef CONFIG_DMA_HELP
-#include "dma.h"
-int command_dma_help(int argc, char **argv)
-{
-	dma_dump(STM32_DMA2_STREAM0);
-	dma_test(STM32_DMA2_STREAM0);
-	dma_dump(STM32_DMA2_STREAM0);
-	return EC_SUCCESS;
-}
-DECLARE_CONSOLE_COMMAND(dmahelp, command_dma_help,
-			NULL, "Run DMA test");
-#endif