diff options
Diffstat (limited to 'board/osiris/board.h')
| -rw-r--r-- | board/osiris/board.h | 138 |
1 files changed, 70 insertions, 68 deletions
diff --git a/board/osiris/board.h b/board/osiris/board.h index 292a540087..c35cdce314 100644 --- a/board/osiris/board.h +++ b/board/osiris/board.h @@ -1,4 +1,4 @@ -/* Copyright 2022 The Chromium OS Authors. All rights reserved. +/* Copyright 2022 The ChromiumOS Authors * Use of this source code is governed by a BSD-style license that can be * found in the LICENSE file. */ @@ -21,11 +21,16 @@ #define CONFIG_MP2964 +/* Tablet mode is not supported */ +#undef CONFIG_TABLET_MODE +#undef CONFIG_TABLET_MODE_SWITCH +#undef CONFIG_LID_ANGLE + /* LED */ #define CONFIG_LED_ONOFF_STATES /* USB Type A Features */ -#define USB_PORT_COUNT 1 +#define USB_PORT_COUNT 1 #define CONFIG_USB_PORT_POWER_DUMB #undef CONFIG_USB_PD_TCPM_NCT38XX @@ -48,17 +53,20 @@ #define CONFIG_USBC_PPC_SYV682X /* TODO: b/177608416 - measure and check these values on osiris */ -#define PD_POWER_SUPPLY_TURN_ON_DELAY 30000 /* us */ -#define PD_POWER_SUPPLY_TURN_OFF_DELAY 30000 /* us */ -#define PD_VCONN_SWAP_DELAY 5000 /* us */ +#define PD_POWER_SUPPLY_TURN_ON_DELAY 30000 /* us */ +#define PD_POWER_SUPPLY_TURN_OFF_DELAY 30000 /* us */ +#define PD_VCONN_SWAP_DELAY 5000 /* us */ /* * Passive USB-C cables only support up to 60W. */ -#define PD_OPERATING_POWER_MW 15000 -#define PD_MAX_POWER_MW 60000 -#define PD_MAX_CURRENT_MA 3000 -#define PD_MAX_VOLTAGE_MV 20000 +#define PD_OPERATING_POWER_MW 15000 +#define PD_MAX_POWER_MW 60000 +#define PD_MAX_CURRENT_MA 3000 +#define PD_MAX_VOLTAGE_MV 20000 + +#define CONFIG_CHARGER_PROFILE_OVERRIDE +#define CONFIG_PWR_STATE_DISCHARGE_FULL /* * Macros for GPIO signals used in common code that don't match the @@ -66,56 +74,55 @@ * then redefined here to so it's more clear which signal is being used for * which purpose. */ -#define GPIO_AC_PRESENT GPIO_ACOK_OD -#define GPIO_CPU_PROCHOT GPIO_EC_PROCHOT_ODL -#define GPIO_EC_INT_L GPIO_EC_PCH_INT_ODL -#define GPIO_ENABLE_BACKLIGHT GPIO_EC_EN_EDP_BL -#define GPIO_ENTERING_RW GPIO_EC_ENTERING_RW -#define GPIO_KBD_KSO2 GPIO_EC_KSO_02_INV -#define GPIO_PACKET_MODE_EN GPIO_EC_GSC_PACKET_MODE -#define GPIO_PCH_PWRBTN_L GPIO_EC_PCH_PWR_BTN_ODL -#define GPIO_PCH_RSMRST_L GPIO_EC_PCH_RSMRST_L -#define GPIO_PCH_RTCRST GPIO_EC_PCH_RTCRST -#define GPIO_PCH_SLP_S0_L GPIO_SYS_SLP_S0IX_L -#define GPIO_PCH_SLP_S3_L GPIO_SLP_S3_L -#define GPIO_TEMP_SENSOR_POWER GPIO_SEQ_EC_DSW_PWROK +#define GPIO_AC_PRESENT GPIO_ACOK_OD +#define GPIO_CPU_PROCHOT GPIO_EC_PROCHOT_ODL +#define GPIO_EC_INT_L GPIO_EC_PCH_INT_ODL +#define GPIO_ENABLE_BACKLIGHT GPIO_EC_EN_EDP_BL +#define GPIO_ENTERING_RW GPIO_EC_ENTERING_RW +#define GPIO_KBD_KSO2 GPIO_EC_KSO_02_INV +#define GPIO_PACKET_MODE_EN GPIO_EC_GSC_PACKET_MODE +#define GPIO_PCH_PWRBTN_L GPIO_EC_PCH_PWR_BTN_ODL +#define GPIO_PCH_RSMRST_L GPIO_EC_PCH_RSMRST_L +#define GPIO_PCH_RTCRST GPIO_EC_PCH_RTCRST +#define GPIO_PCH_SLP_S0_L GPIO_SYS_SLP_S0IX_L +#define GPIO_PCH_SLP_S3_L GPIO_SLP_S3_L +#define GPIO_TEMP_SENSOR_POWER GPIO_SEQ_EC_DSW_PWROK /* * GPIO_EC_PCH_INT_ODL is used for MKBP events as well as a PCH wakeup * signal. */ -#define GPIO_PCH_WAKE_L GPIO_EC_PCH_INT_ODL -#define GPIO_PG_EC_ALL_SYS_PWRGD GPIO_SEQ_EC_ALL_SYS_PG -#define GPIO_PG_EC_DSW_PWROK GPIO_SEQ_EC_DSW_PWROK -#define GPIO_PG_EC_RSMRST_ODL GPIO_SEQ_EC_RSMRST_ODL -#define GPIO_POWER_BUTTON_L GPIO_GSC_EC_PWR_BTN_ODL -#define GPIO_SYS_RESET_L GPIO_SYS_RST_ODL -#define GPIO_WP_L GPIO_EC_WP_ODL - +#define GPIO_PCH_WAKE_L GPIO_EC_PCH_INT_ODL +#define GPIO_PG_EC_ALL_SYS_PWRGD GPIO_SEQ_EC_ALL_SYS_PG +#define GPIO_PG_EC_DSW_PWROK GPIO_SEQ_EC_DSW_PWROK +#define GPIO_PG_EC_RSMRST_ODL GPIO_SEQ_EC_RSMRST_ODL +#define GPIO_POWER_BUTTON_L GPIO_GSC_EC_PWR_BTN_ODL +#define GPIO_SYS_RESET_L GPIO_SYS_RST_ODL +#define GPIO_WP_L GPIO_EC_WP_ODL /* I2C Bus Configuration */ -#define I2C_PORT_RGBKB NPCX_I2C_PORT0_0 +#define I2C_PORT_RGBKB NPCX_I2C_PORT0_0 -#define I2C_PORT_USB_C0_C2_TCPC NPCX_I2C_PORT1_0 -#define I2C_PORT_USB_C1_TCPC NPCX_I2C_PORT4_1 +#define I2C_PORT_USB_C0_C2_TCPC NPCX_I2C_PORT1_0 +#define I2C_PORT_USB_C1_TCPC NPCX_I2C_PORT4_1 -#define I2C_PORT_USB_C0_C2_PPC NPCX_I2C_PORT2_0 -#define I2C_PORT_USB_C1_PPC NPCX_I2C_PORT6_1 +#define I2C_PORT_USB_C0_C2_PPC NPCX_I2C_PORT2_0 +#define I2C_PORT_USB_C1_PPC NPCX_I2C_PORT6_1 -#define I2C_PORT_USB_C0_C2_BC12 NPCX_I2C_PORT2_0 -#define I2C_PORT_USB_C1_BC12 NPCX_I2C_PORT6_1 +#define I2C_PORT_USB_C0_C2_BC12 NPCX_I2C_PORT2_0 +#define I2C_PORT_USB_C1_BC12 NPCX_I2C_PORT6_1 -#define I2C_PORT_USB_C1_MUX NPCX_I2C_PORT6_1 +#define I2C_PORT_USB_C1_MUX NPCX_I2C_PORT6_1 -#define I2C_PORT_BATTERY NPCX_I2C_PORT5_0 -#define I2C_PORT_CHARGER NPCX_I2C_PORT7_0 -#define I2C_PORT_EEPROM NPCX_I2C_PORT7_0 -#define I2C_PORT_MP2964 NPCX_I2C_PORT7_0 +#define I2C_PORT_BATTERY NPCX_I2C_PORT5_0 +#define I2C_PORT_CHARGER NPCX_I2C_PORT7_0 +#define I2C_PORT_EEPROM NPCX_I2C_PORT7_0 +#define I2C_PORT_MP2964 NPCX_I2C_PORT7_0 -#define I2C_ADDR_EEPROM_FLAGS 0x50 +#define I2C_ADDR_EEPROM_FLAGS 0x50 -#define I2C_ADDR_MP2964_FLAGS 0x20 +#define I2C_ADDR_MP2964_FLAGS 0x20 /* Thermal features */ #define CONFIG_THERMISTOR @@ -123,32 +130,37 @@ #define CONFIG_TEMP_SENSOR_POWER #define CONFIG_STEINHART_HART_3V3_30K9_47K_4050B -#define CONFIG_FANS FAN_CH_COUNT +#define CONFIG_FANS FAN_CH_COUNT +#define CONFIG_FAN_RPM_CUSTOM /* Charger defines */ #define CONFIG_CHARGER_ISL9241 #define CONFIG_CHARGE_RAMP_SW -#define CONFIG_CHARGER_SENSE_RESISTOR 10 -#define CONFIG_CHARGER_SENSE_RESISTOR_AC 10 +#define CONFIG_CHARGER_SENSE_RESISTOR 10 +#define CONFIG_CHARGER_SENSE_RESISTOR_AC 10 + +/* shutdown if soc <= 3%, default is 4% */ +#undef CONFIG_BATT_HOST_SHUTDOWN_PERCENTAGE +#define CONFIG_BATT_HOST_SHUTDOWN_PERCENTAGE 3 #undef CONFIG_VOLUME_BUTTONS /* RGB Keyboard */ #define CONFIG_KEYBOARD_BACKLIGHT -#define GPIO_RGBKBD_SDB_L GPIO_EC_KB_BL_EN_L +#define GPIO_RGBKBD_SDB_L GPIO_EC_KB_BL_EN_L #ifdef SECTION_IS_RW #define CONFIG_RGB_KEYBOARD -#define CONFIG_LED_DRIVER_IS31FL3733B /* is31fl3733b on I2C */ +#define CONFIG_LED_DRIVER_IS31FL3733B /* is31fl3733b on I2C */ #endif -#define RGB_GRID0_COL 12 -#define RGB_GRID0_ROW 1 -#define I2C_PORT_KBMCU I2C_PORT_RGBKB +#define RGB_GRID0_COL 12 +#define RGB_GRID0_ROW 1 +#define I2C_PORT_KBMCU I2C_PORT_RGBKB #define CONFIG_KEYBOARD_FACTORY_TEST #ifndef __ASSEMBLER__ -#include "gpio_signal.h" /* needed by registers.h */ +#include "gpio_signal.h" /* needed by registers.h */ #include "registers.h" #include "usbc_config.h" @@ -166,27 +178,17 @@ enum temp_sensor_id { TEMP_SENSOR_COUNT }; -enum battery_type { - BATTERY_AP19B8M, - BATTERY_COSMX_AP22ABN, - BATTERY_TYPE_COUNT -}; +enum battery_type { BATTERY_COSMX_AP22ABN, BATTERY_TYPE_COUNT }; enum pwm_channel { - PWM_CH_KBLIGHT = 0, /* PWM3 */ - PWM_CH_FAN, /* PWM5 */ + PWM_CH_FAN = 0, /* PWM5 */ + PWM_CH_FAN2, /* PWM3 */ PWM_CH_COUNT }; -enum fan_channel { - FAN_CH_0 = 0, - FAN_CH_COUNT -}; +enum fan_channel { FAN_CH_0 = 0, FAN_CH_1, FAN_CH_COUNT }; -enum mft_channel { - MFT_CH_0 = 0, - MFT_CH_COUNT -}; +enum mft_channel { MFT_CH_0 = 0, MFT_CH_1, MFT_CH_COUNT }; #ifdef CONFIG_KEYBOARD_FACTORY_TEST extern const int keyboard_factory_scan_pins[][2]; |