diff options
Diffstat (limited to 'board/rainier/gpio.inc')
| -rw-r--r-- | board/rainier/gpio.inc | 93 |
1 files changed, 0 insertions, 93 deletions
diff --git a/board/rainier/gpio.inc b/board/rainier/gpio.inc deleted file mode 100644 index f5a4f360b3..0000000000 --- a/board/rainier/gpio.inc +++ /dev/null @@ -1,93 +0,0 @@ -/* -*- mode:c -*- - * - * Copyright 2017 The Chromium OS Authors. All rights reserved. - * Use of this source code is governed by a BSD-style license that can be - * found in the LICENSE file. - */ - -/* - * Declare symbolic names for all the GPIOs that we care about. - * Note: Those with interrupt handlers must be declared first. - */ - -GPIO_INT(SPI1_NSS, PIN(A, 15), GPIO_INT_BOTH, - spi_event) -GPIO_INT(USB_C0_PD_INT_L, PIN(C, 13), GPIO_INT_FALLING | GPIO_PULL_UP, - tcpc_alert_event) -GPIO_INT(VOLUME_UP_L, PIN(D, 10), GPIO_INT_BOTH | GPIO_PULL_UP, - button_interrupt) -GPIO_INT(VOLUME_DOWN_L, PIN(E, 11), GPIO_INT_BOTH | GPIO_PULL_UP, - button_interrupt) -GPIO_INT(POWER_BUTTON_L, PIN(A, 0), GPIO_INT_BOTH | GPIO_PULL_UP, - power_button_interrupt) -GPIO_INT(PP1250_S3_PG, PIN(D, 8), GPIO_INT_BOTH | GPIO_PULL_UP, - power_signal_interrupt) -GPIO_INT(PP900_S0_PG, PIN(D, 9), GPIO_INT_BOTH | GPIO_PULL_UP, - power_signal_interrupt) -GPIO_INT(AP_EC_S3_S0_L, PIN(C, 7), GPIO_INT_BOTH | GPIO_PULL_DOWN, - power_signal_interrupt) -GPIO_INT(WARM_RESET_REQ, PIN(E, 1), GPIO_INT_RISING | GPIO_PULL_DOWN, - warm_reset_request_interrupt) -GPIO_INT(AP_OVERTEMP, PIN(E, 4), GPIO_INT_RISING | GPIO_PULL_DOWN, - overtemp_interrupt) -GPIO_INT(ACCEL_INT_L, PIN(D, 14), GPIO_INT_FALLING | GPIO_SEL_1P8V, - bmi160_interrupt) - -/* Voltage rails control pins */ -GPIO(PP1800_S0_EN, PIN(D, 11), GPIO_OUT_LOW) -GPIO(AP_CORE_EN, PIN(C, 1), GPIO_OUT_LOW) -GPIO(PP3300_S0_EN, PIN(E, 12), GPIO_OUT_LOW) -GPIO(PP1800_USB_EN, PIN(C, 4), GPIO_OUT_LOW) -GPIO(PP900_S0_EN, PIN(E, 8), GPIO_OUT_LOW) -GPIO(PP1250_S3_EN, PIN(D, 13), GPIO_OUT_LOW) -GPIO(PP1800_S3_EN, PIN(C, 3), GPIO_OUT_LOW) -GPIO(PP3300_S3_EN, PIN(E, 2), GPIO_OUT_LOW) -GPIO(PP900_S3_EN, PIN(E, 10), GPIO_OUT_LOW) - -GPIO(PP3300_REDUCE_EFF_L, PIN(D, 12), GPIO_ODR_HIGH) - -/* - * I2C pins should be configured as inputs until I2C module is - * initialized. This will avoid driving the lines unintentionally. - */ -GPIO(I2C0_SCL, PIN(B, 8), GPIO_INPUT) -GPIO(I2C0_SDA, PIN(B, 9), GPIO_INPUT) -GPIO(I2C1_SCL, PIN(B, 10), GPIO_INPUT) -GPIO(I2C1_SDA, PIN(B, 11), GPIO_INPUT) - -/* Analog pins */ -GPIO(BOARD_ID, PIN(C, 0), GPIO_ANALOG) - -/* SPI sensors */ -GPIO(SPI_BARO_CS_L, PIN(B, 12), GPIO_OUT_HIGH) -GPIO(SPI_ACCEL_CS_L, PIN(D, 0), GPIO_OUT_HIGH) - -/* Other input pins */ -GPIO(WP_L, PIN(E, 5), GPIO_INPUT) -GPIO(CCD_MODE_ODL, PIN(C, 5), GPIO_INPUT | GPIO_PULL_UP) -GPIO(CHARGER_INT_L, PIN(E, 6), GPIO_INPUT | GPIO_PULL_UP) -/* Non-INT power signal pin */ -GPIO(AP_CORE_PG, PIN(D, 7), GPIO_INPUT | GPIO_PULL_UP) - - - -/* Other output pins */ -GPIO(ENTERING_RW, PIN(C, 6), GPIO_ODR_HIGH) -GPIO(SYS_RST_L, PIN(C, 8), GPIO_ODR_HIGH) -GPIO(EC_INT_L, PIN(E, 3), GPIO_ODR_HIGH) -GPIO(EC_BOARD_ID_EN_L, PIN(F, 1), GPIO_ODR_HIGH) -GPIO(USB_C0_DISCHARGE, PIN(A, 11), GPIO_OUT_LOW) -GPIO(PCA9468_EN, PIN(E, 15), GPIO_OUT_LOW) - -/* USART1: PA9/PA10 */ -ALTERNATE(PIN_MASK(A, 0x0600), 1, MODULE_UART, 0) -/* I2C MASTER: PB8/9 */ -ALTERNATE(PIN_MASK(B, 0x0300), 1, MODULE_I2C, 0) -/* I2C MASTER: PB10/11 */ -ALTERNATE(PIN_MASK(B, 0x0c00), 1, MODULE_I2C, 0) -/* SPI SLAVE: PB3/4/5 */ -ALTERNATE(PIN_MASK(B, 0x0038), 0, MODULE_SPI, 0) -/* SPI SLAVE CS: PA15 */ -ALTERNATE(PIN_MASK(A, 0x8000), 0, MODULE_SPI, 0) -/* SPI MASTER: PD1/3/4 */ -ALTERNATE(PIN_MASK(D, 0x001a), 1, MODULE_SPI_CONTROLLER, 0) |