diff options
Diffstat (limited to 'board/rainier')
-rw-r--r-- | board/rainier/board.c | 438 | ||||
-rw-r--r-- | board/rainier/board.h | 176 | ||||
-rw-r--r-- | board/rainier/build.mk | 14 | ||||
-rw-r--r-- | board/rainier/ec.tasklist | 17 | ||||
-rw-r--r-- | board/rainier/gpio.inc | 93 | ||||
-rw-r--r-- | board/rainier/usb_pd_policy.c | 66 | ||||
-rw-r--r-- | board/rainier/vif_override.xml | 3 |
7 files changed, 0 insertions, 807 deletions
diff --git a/board/rainier/board.c b/board/rainier/board.c deleted file mode 100644 index 0f9c388399..0000000000 --- a/board/rainier/board.c +++ /dev/null @@ -1,438 +0,0 @@ -/* Copyright 2017 The Chromium OS Authors. All rights reserved. - * Use of this source code is governed by a BSD-style license that can be - * found in the LICENSE file. - */ - -#include "adc.h" -#include "backlight.h" -#include "button.h" -#include "chipset.h" -#include "charge_manager.h" -#include "charge_state.h" -#include "common.h" -#include "console.h" -#include "ec_commands.h" -#include "driver/accelgyro_bmi_common.h" -#include "driver/baro_bmp280.h" -#include "driver/tcpm/fusb302.h" -#include "driver/temp_sensor/tmp432.h" -#include "extpower.h" -#include "gpio.h" -#include "hooks.h" -#include "host_command.h" -#include "i2c.h" -#include "power.h" -#include "power_button.h" -#include "pwm.h" -#include "pwm_chip.h" -#include "registers.h" -#include "spi.h" -#include "switch.h" -#include "system.h" -#include "task.h" -#include "tcpm/tcpm.h" -#include "temp_sensor.h" -#include "temp_sensor_chip.h" -#include "timer.h" -#include "thermal.h" -#include "usb_charge.h" -#include "usb_mux.h" -#include "usb_pd_tcpm.h" -#include "util.h" - -#define CPRINTS(format, args...) cprints(CC_USBCHARGE, format, ## args) -#define CPRINTF(format, args...) cprintf(CC_USBCHARGE, format, ## args) - -static void tcpc_alert_event(enum gpio_signal signal) -{ - schedule_deferred_pd_interrupt(0 /* port */); -} - -static void overtemp_interrupt(enum gpio_signal signal) -{ - CPRINTS("AP wants shutdown"); - chipset_force_shutdown(CHIPSET_SHUTDOWN_THERMAL); -} - -static void warm_reset_request_interrupt(enum gpio_signal signal) -{ - CPRINTS("AP wants warm reset"); - chipset_reset(CHIPSET_RESET_AP_REQ); -} - -#include "gpio_list.h" - -/******************************************************************************/ -/* ADC channels. Must be in the exactly same order as in enum adc_channel. */ -const struct adc_t adc_channels[] = { - [ADC_BOARD_ID] = {"BOARD_ID", 16, 4096, 0, STM32_AIN(10)}, -}; -BUILD_ASSERT(ARRAY_SIZE(adc_channels) == ADC_CH_COUNT); - -/******************************************************************************/ -/* I2C ports */ -const struct i2c_port_t i2c_ports[] = { - {"tcpc0", I2C_PORT_TCPC0, 1000, GPIO_I2C1_SCL, GPIO_I2C1_SDA}, -}; -const unsigned int i2c_ports_used = ARRAY_SIZE(i2c_ports); - -/* power signal list. Must match order of enum power_signal. */ -const struct power_signal_info power_signal_list[] = { - {GPIO_PP1250_S3_PG, POWER_SIGNAL_ACTIVE_HIGH, "PP1250_S3_PWR_GOOD"}, - {GPIO_PP900_S0_PG, POWER_SIGNAL_ACTIVE_HIGH, "PP900_S0_PWR_GOOD"}, - {GPIO_AP_CORE_PG, POWER_SIGNAL_ACTIVE_HIGH, "AP_PWR_GOOD"}, - {GPIO_AP_EC_S3_S0_L, POWER_SIGNAL_ACTIVE_LOW, "SUSPEND_DEASSERTED"}, -}; -BUILD_ASSERT(ARRAY_SIZE(power_signal_list) == POWER_SIGNAL_COUNT); - -#ifdef CONFIG_TEMP_SENSOR_TMP432 -/* Temperature sensors data; must be in same order as enum temp_sensor_id. */ -const struct temp_sensor_t temp_sensors[] = { - {"TMP432_Internal", TEMP_SENSOR_TYPE_BOARD, tmp432_get_val, - TMP432_IDX_LOCAL, 4}, - {"TMP432_Sensor_1", TEMP_SENSOR_TYPE_BOARD, tmp432_get_val, - TMP432_IDX_REMOTE1, 4}, - {"TMP432_Sensor_2", TEMP_SENSOR_TYPE_BOARD, tmp432_get_val, - TMP432_IDX_REMOTE2, 4}, -}; -BUILD_ASSERT(ARRAY_SIZE(temp_sensors) == TEMP_SENSOR_COUNT); - -/* - * Thermal limits for each temp sensor. All temps are in degrees K. Must be in - * same order as enum temp_sensor_id. To always ignore any temp, use 0. - */ -struct ec_thermal_config thermal_params[] = { - {{0, 0, 0}, 0, 0}, /* TMP432_Internal */ - {{0, 0, 0}, 0, 0}, /* TMP432_Sensor_1 */ - {{0, 0, 0}, 0, 0}, /* TMP432_Sensor_2 */ -}; -BUILD_ASSERT(ARRAY_SIZE(thermal_params) == TEMP_SENSOR_COUNT); -#endif - -/******************************************************************************/ -/* SPI devices */ -const struct spi_device_t spi_devices[] = { - { CONFIG_SPI_ACCEL_PORT, 1, GPIO_SPI_ACCEL_CS_L }, - { CONFIG_SPI_ACCEL_PORT, 1, GPIO_SPI_BARO_CS_L }, -}; -const unsigned int spi_devices_used = ARRAY_SIZE(spi_devices); - -/******************************************************************************/ -/* Wake-up pins for hibernate */ -const enum gpio_signal hibernate_wake_pins[] = { - GPIO_POWER_BUTTON_L, GPIO_CHARGER_INT_L -}; -const int hibernate_wake_pins_used = ARRAY_SIZE(hibernate_wake_pins); - -/******************************************************************************/ -const struct tcpc_config_t tcpc_config[CONFIG_USB_PD_PORT_MAX_COUNT] = { - { - .bus_type = EC_BUS_TYPE_I2C, - .i2c_info = { - .port = I2C_PORT_TCPC0, - .addr_flags = FUSB302_I2C_ADDR_FLAGS, - }, - .drv = &fusb302_tcpm_drv, - }, -}; - -const struct usb_mux usb_muxes[CONFIG_USB_PD_PORT_MAX_COUNT] = { - { - .usb_port = 0, - .driver = &virtual_usb_mux_driver, - .hpd_update = &virtual_hpd_update, - }, -}; - -void board_reset_pd_mcu(void) -{ -} - -uint16_t tcpc_get_alert_status(void) -{ - uint16_t status = 0; - - if (!gpio_get_level(GPIO_USB_C0_PD_INT_L)) - status |= PD_STATUS_TCPC_ALERT_0; - - return status; -} - -int board_set_active_charge_port(int charge_port) -{ - /* - * NOP because there is no internal power therefore no charging. - * Placeholder so common/charge_manager.c is built. - */ - return EC_SUCCESS; -} - -void board_set_charge_limit(int port, int supplier, int charge_ma, - int max_ma, int charge_mv) -{ - /* - * NOP because there is no internal power therefore no charging. - * Placeholder so common/charge_manager.c is built. - */ -} - -int extpower_is_present(void) -{ - /* There is no internal power on this board. */ - return 1; -} - -int pd_snk_is_vbus_provided(int port) -{ - /* Must be, if we're at a stage where this function is called. */ - return 1; -} - -static void board_spi_enable(void) -{ - gpio_config_module(MODULE_SPI_CONTROLLER, 1); - - /* Enable clocks to SPI2 module */ - STM32_RCC_APB1ENR |= STM32_RCC_PB1_SPI2; - - /* Reset SPI2 */ - STM32_RCC_APB1RSTR |= STM32_RCC_PB1_SPI2; - STM32_RCC_APB1RSTR &= ~STM32_RCC_PB1_SPI2; - - spi_enable(&spi_devices[0], 1); -} -DECLARE_HOOK(HOOK_CHIPSET_STARTUP, - board_spi_enable, - MOTION_SENSE_HOOK_PRIO - 1); - -static void board_spi_disable(void) -{ - spi_enable(&spi_devices[0], 0); - - /* Disable clocks to SPI2 module */ - STM32_RCC_APB1ENR &= ~STM32_RCC_PB1_SPI2; - - gpio_config_module(MODULE_SPI_CONTROLLER, 0); -} -DECLARE_HOOK(HOOK_CHIPSET_SHUTDOWN, - board_spi_disable, - MOTION_SENSE_HOOK_PRIO + 1); - -static void board_init(void) -{ - /* Enable TCPC alert interrupts */ - gpio_enable_interrupt(GPIO_USB_C0_PD_INT_L); - - /* Enable reboot / shutdown control inputs from AP */ - gpio_enable_interrupt(GPIO_WARM_RESET_REQ); - gpio_enable_interrupt(GPIO_AP_OVERTEMP); - - /* Enable interrupts from BMI160 sensor. */ - gpio_enable_interrupt(GPIO_ACCEL_INT_L); - - /* Set SPI2 pins to high speed */ - /* pins D0/D1/D3/D4 */ - STM32_GPIO_OSPEEDR(GPIO_D) |= 0x000003cf; - - /* Sensor Init */ - if (system_jumped_late() && chipset_in_state(CHIPSET_STATE_ON)) - board_spi_enable(); -} -DECLARE_HOOK(HOOK_INIT, board_init, HOOK_PRIO_DEFAULT); - -void board_config_pre_init(void) -{ - STM32_RCC_AHBENR |= STM32_RCC_HB_DMA1; - /* - * Remap USART1 and SPI2 DMA: - * - * Ch4: USART1_TX / Ch5: USART1_RX (1000) - * Ch6: SPI2_RX / Ch7: SPI2_TX (0011) - */ - STM32_DMA_CSELR(STM32_DMAC_CH4) = (8 << 12) | (8 << 16) | - (3 << 20) | (3 << 24); -} - -void board_hibernate(void) -{ - int rv; - - /* - * Disable the power enables for the TCPCs since we're going into - * hibernate. The charger VBUS interrupt will wake us up and reset the - * EC. Upon init, we'll reinitialize the TCPCs to be at full power. - */ - CPRINTS("Set TCPCs to low power"); - rv = tcpc_write(0, TCPC_REG_POWER, TCPC_REG_POWER_PWR_LOW); - if (rv) - CPRINTS("Error setting TCPC %d", 0); - - cflush(); -} - -enum rainier_board_version { - BOARD_VERSION_UNKNOWN = -1, - BOARD_VERSION_REV0 = 0, - BOARD_VERSION_REV1 = 1, - BOARD_VERSION_REV2 = 2, - BOARD_VERSION_REV3 = 3, - BOARD_VERSION_REV4 = 4, - BOARD_VERSION_REV5 = 5, - BOARD_VERSION_REV6 = 6, - BOARD_VERSION_REV7 = 7, - BOARD_VERSION_REV8 = 8, - BOARD_VERSION_REV9 = 9, - BOARD_VERSION_REV10 = 10, - BOARD_VERSION_REV11 = 11, - BOARD_VERSION_REV12 = 12, - BOARD_VERSION_REV13 = 13, - BOARD_VERSION_REV14 = 14, - BOARD_VERSION_REV15 = 15, - BOARD_VERSION_COUNT, -}; - -struct { - enum rainier_board_version version; - int expect_mv; -} const rainier_boards[] = { - { BOARD_VERSION_REV0, 109 }, /* 51.1K , 2.2K(gru 3.3K) ohm */ - { BOARD_VERSION_REV1, 211 }, /* 51.1k , 6.8K ohm */ - { BOARD_VERSION_REV2, 319 }, /* 51.1K , 11K ohm */ - { BOARD_VERSION_REV3, 427 }, /* 56K , 17.4K ohm */ - { BOARD_VERSION_REV4, 542 }, /* 51.1K , 22K ohm */ - { BOARD_VERSION_REV5, 666 }, /* 51.1K , 30K ohm */ - { BOARD_VERSION_REV6, 781 }, /* 51.1K , 39.2K ohm */ - { BOARD_VERSION_REV7, 900 }, /* 56K , 56K ohm */ - { BOARD_VERSION_REV8, 1023 }, /* 47K , 61.9K ohm */ - { BOARD_VERSION_REV9, 1137 }, /* 47K , 80.6K ohm */ - { BOARD_VERSION_REV10, 1240 }, /* 56K , 124K ohm */ - { BOARD_VERSION_REV11, 1343 }, /* 51.1K , 150K ohm */ - { BOARD_VERSION_REV12, 1457 }, /* 47K , 200K ohm */ - { BOARD_VERSION_REV13, 1576 }, /* 47K , 330K ohm */ - { BOARD_VERSION_REV14, 1684 }, /* 47K , 680K ohm */ - { BOARD_VERSION_REV15, 1800 }, /* 56K , NC */ -}; -BUILD_ASSERT(ARRAY_SIZE(rainier_boards) == BOARD_VERSION_COUNT); - -#define THRESHOLD_MV 56 /* Simply assume 1800/16/2 */ - -int board_get_version(void) -{ - static int version = BOARD_VERSION_UNKNOWN; - int mv; - int i; - - if (version != BOARD_VERSION_UNKNOWN) - return version; - - gpio_set_level(GPIO_EC_BOARD_ID_EN_L, 0); - /* Wait to allow cap charge */ - msleep(10); - mv = adc_read_channel(ADC_BOARD_ID); - - if (mv == ADC_READ_ERROR) - mv = adc_read_channel(ADC_BOARD_ID); - - gpio_set_level(GPIO_EC_BOARD_ID_EN_L, 1); - - for (i = 0; i < BOARD_VERSION_COUNT; ++i) { - if (mv < rainier_boards[i].expect_mv + THRESHOLD_MV) { - version = rainier_boards[i].version; - break; - } - } - - return version; -} - -/* Motion sensors */ -/* Mutexes */ -static struct mutex g_base_mutex; - -static struct bmi_drv_data_t g_bmi160_data; - -/* Matrix to rotate accelerometer into standard reference frame */ -const mat33_fp_t base_standard_ref = { - { 0, FLOAT_TO_FP(1), 0}, - { FLOAT_TO_FP(-1), 0, 0}, - { 0, 0, FLOAT_TO_FP(1)} -}; - -static struct bmp280_drv_data_t bmp280_drv_data; - -struct motion_sensor_t motion_sensors[] = { - /* - * Note: bmi160: supports accelerometer and gyro sensor - * Requirement: accelerometer sensor must init before gyro sensor - * DO NOT change the order of the following table. - */ - [LID_ACCEL] = { - .name = "Accel", - .active_mask = SENSOR_ACTIVE_S0_S3, - .chip = MOTIONSENSE_CHIP_BMI160, - .type = MOTIONSENSE_TYPE_ACCEL, - .location = MOTIONSENSE_LOC_LID, - .drv = &bmi160_drv, - .mutex = &g_base_mutex, - .drv_data = &g_bmi160_data, - .port = CONFIG_SPI_ACCEL_PORT, - .i2c_spi_addr_flags = ACCEL_MK_SPI_ADDR_FLAGS(CONFIG_SPI_ACCEL_PORT), - .rot_standard_ref = &base_standard_ref, - .default_range = 4, /* g, to meet CDD 7.3.1/C-1-4 reqs */ - .min_frequency = BMI_ACCEL_MIN_FREQ, - .max_frequency = BMI_ACCEL_MAX_FREQ, - .config = { - /* Enable accel in S0 */ - [SENSOR_CONFIG_EC_S0] = { - .odr = 10000 | ROUND_UP_FLAG, - .ec_rate = 100 * MSEC, - }, - }, - }, - [LID_GYRO] = { - .name = "Gyro", - .active_mask = SENSOR_ACTIVE_S0_S3, - .chip = MOTIONSENSE_CHIP_BMI160, - .type = MOTIONSENSE_TYPE_GYRO, - .location = MOTIONSENSE_LOC_LID, - .drv = &bmi160_drv, - .mutex = &g_base_mutex, - .drv_data = &g_bmi160_data, - .port = CONFIG_SPI_ACCEL_PORT, - .i2c_spi_addr_flags = ACCEL_MK_SPI_ADDR_FLAGS(CONFIG_SPI_ACCEL_PORT), - .default_range = 1000, /* dps */ - .rot_standard_ref = &base_standard_ref, - .min_frequency = BMI_GYRO_MIN_FREQ, - .max_frequency = BMI_GYRO_MAX_FREQ, - }, - [LID_BARO] = { - .name = "Baro", - .active_mask = SENSOR_ACTIVE_S0_S3, - .chip = MOTIONSENSE_CHIP_BMP280, - .type = MOTIONSENSE_TYPE_BARO, - .location = MOTIONSENSE_LOC_LID, - .drv = &bmp280_drv, - .drv_data = &bmp280_drv_data, - .port = CONFIG_SPI_ACCEL_PORT, - .i2c_spi_addr_flags = ACCEL_MK_SPI_ADDR_FLAGS(CONFIG_SPI_ACCEL_PORT), - .default_range = BIT(18), /* 1bit = 4 Pa, 16bit ~= 2600 hPa */ - .min_frequency = BMP280_BARO_MIN_FREQ, - .max_frequency = BMP280_BARO_MAX_FREQ, - }, -}; -const unsigned int motion_sensor_count = ARRAY_SIZE(motion_sensors); - -int board_allow_i2c_passthru(int port) -{ - /* - * Battery port is the only port passthru is allowed on and this board - * does not have a battery, therefore always return false. - */ - return 0; -} - -int charge_prevent_power_on(int power_button_pressed) -{ - /* Assume there is always sufficient power from charger to power on. */ - return 0; -} diff --git a/board/rainier/board.h b/board/rainier/board.h deleted file mode 100644 index a323a90889..0000000000 --- a/board/rainier/board.h +++ /dev/null @@ -1,176 +0,0 @@ -/* Copyright 2017 The Chromium OS Authors. All rights reserved. - * Use of this source code is governed by a BSD-style license that can be - * found in the LICENSE file. - */ - -/* Configuration for Rainier */ - -#ifndef __CROS_EC_BOARD_H -#define __CROS_EC_BOARD_H - -/* Optional modules */ -#define CONFIG_ADC -#undef CONFIG_ADC_WATCHDOG -#define CONFIG_CHIPSET_RK3399 -#define CONFIG_CMD_ACCELS -#define CONFIG_CMD_RTC -#define CONFIG_HOSTCMD_RTC -#define CONFIG_I2C -#define CONFIG_I2C_CONTROLLER -#define CONFIG_I2C_PASSTHRU_RESTRICTED -#define CONFIG_LOW_POWER_IDLE -#define CONFIG_POWER_COMMON -#define CONFIG_SPI -#define CONFIG_SPI_CONTROLLER -#define CONFIG_STM_HWTIMER32 -/* Source RTCCLK from external 32.768kHz source on PC15/OSC32_IN. */ -#define CONFIG_STM32_CLOCK_LSE -#define CONFIG_SWITCH -#define CONFIG_WATCHDOG_HELP - -#define CONFIG_SYSTEM_UNLOCKED /* Allow dangerous commands for testing */ - -#undef CONFIG_UART_CONSOLE -#define CONFIG_UART_CONSOLE 1 - -/* Region sizes are no longer a power of 2 so we can't enable MPU */ -#undef CONFIG_MPU - -/* Enable a different power-on sequence than the one on gru */ -#undef CONFIG_CHIPSET_POWER_SEQ_VERSION -#define CONFIG_CHIPSET_POWER_SEQ_VERSION 1 - -/* Optional features */ -#define CONFIG_BOARD_PRE_INIT -#define CONFIG_BUTTON_TRIGGERED_RECOVERY -#define CONFIG_CHARGER_ILIM_PIN_DISABLED -#define CONFIG_FORCE_CONSOLE_RESUME -#define CONFIG_HOST_COMMAND_STATUS - -/* By default, set hcdebug to off */ -#undef CONFIG_HOSTCMD_DEBUG_MODE -#define CONFIG_HOSTCMD_DEBUG_MODE HCDEBUG_OFF -#undef CONFIG_LID_SWITCH -#undef CONFIG_LTO -#define CONFIG_POWER_BUTTON -#define CONFIG_POWER_BUTTON_IGNORE_LID -#define CONFIG_POWER_TRACK_HOST_SLEEP_STATE -#define CONFIG_SOFTWARE_PANIC -#define CONFIG_VBOOT_HASH -#define CONFIG_VOLUME_BUTTONS - -#define CONFIG_USB_MUX_VIRTUAL - -/* Increase tx buffer size, as we'd like to stream EC log to AP. */ -#undef CONFIG_UART_TX_BUF_SIZE -#define CONFIG_UART_TX_BUF_SIZE 4096 - -/* Motion Sensors */ -#define CONFIG_ACCELGYRO_BMI160 -#define CONFIG_ACCEL_INTERRUPTS -#define CONFIG_ACCELGYRO_BMI160_INT_EVENT \ - TASK_EVENT_MOTION_SENSOR_INTERRUPT(LID_ACCEL) -#define CONFIG_BARO_BMP280 - -/* To be able to indicate the device is in tablet mode. */ -#define CONFIG_TABLET_MODE -#define CONFIG_TABLET_MODE_SWITCH - -/* Enable sensor fifo, must also define the _SIZE and _THRES */ -#define CONFIG_ACCEL_FIFO -/* FIFO size is in power of 2. */ -#define CONFIG_ACCEL_FIFO_SIZE 256 -/* Depends on how fast the AP boots and typical ODRs. */ -#define CONFIG_ACCEL_FIFO_THRES (CONFIG_ACCEL_FIFO_SIZE / 3) - -/* Sensors without hardware FIFO are in forced mode. */ -#define CONFIG_ACCEL_FORCE_MODE_MASK BIT(LID_BARO) - -/* USB PD config */ -#define CONFIG_CHARGE_MANAGER -#define CONFIG_USB_POWER_DELIVERY -#define CONFIG_USB_PD_TCPMV1 -#define CONFIG_USB_PD_ALT_MODE -#define CONFIG_USB_PD_ALT_MODE_DFP -#define CONFIG_USB_PD_DISCHARGE_GPIO -#define CONFIG_USB_PD_DUAL_ROLE -#define CONFIG_USB_PD_PORT_MAX_COUNT 1 -#define CONFIG_USB_PD_TCPM_FUSB302 -#define CONFIG_USB_PD_TCPM_TCPCI -#define CONFIG_USB_PD_VBUS_DETECT_TCPC -#define CONFIG_USB_PD_VBUS_MEASURE_NOT_PRESENT -#define CONFIG_USBC_SS_MUX -#define CONFIG_USBC_VCONN -#define CONFIG_USBC_VCONN_SWAP -#define CONFIG_USB_PD_COMM_LOCKED - -#define PD_OPERATING_POWER_MW 15000 -#define PD_MAX_POWER_MW ((PD_MAX_VOLTAGE_MV * PD_MAX_CURRENT_MA) / 1000) -#define PD_MAX_CURRENT_MA 3000 -#define PD_MAX_VOLTAGE_MV 12850 - -#define PD_POWER_SUPPLY_TURN_ON_DELAY 30000 /* us */ -#define PD_POWER_SUPPLY_TURN_OFF_DELAY 50000 /* us */ - -/* Timer selection */ -#define TIM_CLOCK32 2 -#define TIM_WATCHDOG 7 - -/* 48 MHz SYSCLK clock frequency */ -#define CPU_CLOCK 48000000 - -/* Optional for testing */ -#undef CONFIG_PECI -#undef CONFIG_PSTORE - -#define CONFIG_TASK_PROFILING - -#define I2C_PORT_TCPC0 1 - -/* Enable Accel over SPI */ -#define CONFIG_SPI_ACCEL_PORT 0 /* The first SPI master port (SPI2) */ - -#define CONFIG_MKBP_INPUT_DEVICES -#define CONFIG_MKBP_EVENT -#define CONFIG_MKBP_USE_GPIO -/* Define the host events which are allowed to wakeup AP in S3. */ -#define CONFIG_MKBP_HOST_EVENT_WAKEUP_MASK \ - (EC_HOST_EVENT_MASK(EC_HOST_EVENT_POWER_BUTTON) |\ - EC_HOST_EVENT_MASK(EC_HOST_EVENT_RTC)) - -#ifndef __ASSEMBLER__ - -enum adc_channel { - /* Real ADC channels begin here */ - ADC_BOARD_ID = 0, - ADC_CH_COUNT -}; - -/* power signal definitions */ -enum power_signal { - PP1250_S3_PWR_GOOD = 0, - PP900_S0_PWR_GOOD, - AP_PWR_GOOD, - SUSPEND_DEASSERTED, - - /* Number of signals */ - POWER_SIGNAL_COUNT, -}; - -/* Motion sensors */ -enum sensor_id { - LID_ACCEL = 0, - LID_GYRO, - LID_BARO, - SENSOR_COUNT, -}; - -#include "gpio_signal.h" -#include "registers.h" - -void board_reset_pd_mcu(void); -int board_get_version(void); - -#endif /* !__ASSEMBLER__ */ - -#endif /* __CROS_EC_BOARD_H */ diff --git a/board/rainier/build.mk b/board/rainier/build.mk deleted file mode 100644 index b77a900d56..0000000000 --- a/board/rainier/build.mk +++ /dev/null @@ -1,14 +0,0 @@ -# -*- makefile -*- -# Copyright 2017 The Chromium OS Authors. All rights reserved. -# Use of this source code is governed by a BSD-style license that can be -# found in the LICENSE file. -# -# Board specific files build -# -# -# STmicro STM32F098VC -CHIP:=stm32 -CHIP_FAMILY:=stm32f0 -CHIP_VARIANT:=stm32f09x - -board-y=board.o usb_pd_policy.o diff --git a/board/rainier/ec.tasklist b/board/rainier/ec.tasklist deleted file mode 100644 index ed574a1d6a..0000000000 --- a/board/rainier/ec.tasklist +++ /dev/null @@ -1,17 +0,0 @@ -/* Copyright 2017 The Chromium OS Authors. All rights reserved. - * Use of this source code is governed by a BSD-style license that can be - * found in the LICENSE file. - */ - -/** - * See CONFIG_TASK_LIST in config.h for details. - */ -#define CONFIG_TASK_LIST \ - TASK_ALWAYS(HOOKS, hook_task, NULL, LARGER_TASK_STACK_SIZE) \ - TASK_NOTEST(CHIPSET, chipset_task, NULL, LARGER_TASK_STACK_SIZE) \ - TASK_ALWAYS(MOTIONSENSE, motion_sense_task, NULL, VENTI_TASK_STACK_SIZE) \ - TASK_ALWAYS(HOSTCMD, host_command_task, NULL, LARGER_TASK_STACK_SIZE) \ - TASK_ALWAYS(CONSOLE, console_task, NULL, LARGER_TASK_STACK_SIZE) \ - TASK_ALWAYS(PD_C0, pd_task, NULL, LARGER_TASK_STACK_SIZE) \ - TASK_ALWAYS(PD_INT_C0, pd_interrupt_handler_task, 0, TASK_STACK_SIZE) - diff --git a/board/rainier/gpio.inc b/board/rainier/gpio.inc deleted file mode 100644 index f5a4f360b3..0000000000 --- a/board/rainier/gpio.inc +++ /dev/null @@ -1,93 +0,0 @@ -/* -*- mode:c -*- - * - * Copyright 2017 The Chromium OS Authors. All rights reserved. - * Use of this source code is governed by a BSD-style license that can be - * found in the LICENSE file. - */ - -/* - * Declare symbolic names for all the GPIOs that we care about. - * Note: Those with interrupt handlers must be declared first. - */ - -GPIO_INT(SPI1_NSS, PIN(A, 15), GPIO_INT_BOTH, - spi_event) -GPIO_INT(USB_C0_PD_INT_L, PIN(C, 13), GPIO_INT_FALLING | GPIO_PULL_UP, - tcpc_alert_event) -GPIO_INT(VOLUME_UP_L, PIN(D, 10), GPIO_INT_BOTH | GPIO_PULL_UP, - button_interrupt) -GPIO_INT(VOLUME_DOWN_L, PIN(E, 11), GPIO_INT_BOTH | GPIO_PULL_UP, - button_interrupt) -GPIO_INT(POWER_BUTTON_L, PIN(A, 0), GPIO_INT_BOTH | GPIO_PULL_UP, - power_button_interrupt) -GPIO_INT(PP1250_S3_PG, PIN(D, 8), GPIO_INT_BOTH | GPIO_PULL_UP, - power_signal_interrupt) -GPIO_INT(PP900_S0_PG, PIN(D, 9), GPIO_INT_BOTH | GPIO_PULL_UP, - power_signal_interrupt) -GPIO_INT(AP_EC_S3_S0_L, PIN(C, 7), GPIO_INT_BOTH | GPIO_PULL_DOWN, - power_signal_interrupt) -GPIO_INT(WARM_RESET_REQ, PIN(E, 1), GPIO_INT_RISING | GPIO_PULL_DOWN, - warm_reset_request_interrupt) -GPIO_INT(AP_OVERTEMP, PIN(E, 4), GPIO_INT_RISING | GPIO_PULL_DOWN, - overtemp_interrupt) -GPIO_INT(ACCEL_INT_L, PIN(D, 14), GPIO_INT_FALLING | GPIO_SEL_1P8V, - bmi160_interrupt) - -/* Voltage rails control pins */ -GPIO(PP1800_S0_EN, PIN(D, 11), GPIO_OUT_LOW) -GPIO(AP_CORE_EN, PIN(C, 1), GPIO_OUT_LOW) -GPIO(PP3300_S0_EN, PIN(E, 12), GPIO_OUT_LOW) -GPIO(PP1800_USB_EN, PIN(C, 4), GPIO_OUT_LOW) -GPIO(PP900_S0_EN, PIN(E, 8), GPIO_OUT_LOW) -GPIO(PP1250_S3_EN, PIN(D, 13), GPIO_OUT_LOW) -GPIO(PP1800_S3_EN, PIN(C, 3), GPIO_OUT_LOW) -GPIO(PP3300_S3_EN, PIN(E, 2), GPIO_OUT_LOW) -GPIO(PP900_S3_EN, PIN(E, 10), GPIO_OUT_LOW) - -GPIO(PP3300_REDUCE_EFF_L, PIN(D, 12), GPIO_ODR_HIGH) - -/* - * I2C pins should be configured as inputs until I2C module is - * initialized. This will avoid driving the lines unintentionally. - */ -GPIO(I2C0_SCL, PIN(B, 8), GPIO_INPUT) -GPIO(I2C0_SDA, PIN(B, 9), GPIO_INPUT) -GPIO(I2C1_SCL, PIN(B, 10), GPIO_INPUT) -GPIO(I2C1_SDA, PIN(B, 11), GPIO_INPUT) - -/* Analog pins */ -GPIO(BOARD_ID, PIN(C, 0), GPIO_ANALOG) - -/* SPI sensors */ -GPIO(SPI_BARO_CS_L, PIN(B, 12), GPIO_OUT_HIGH) -GPIO(SPI_ACCEL_CS_L, PIN(D, 0), GPIO_OUT_HIGH) - -/* Other input pins */ -GPIO(WP_L, PIN(E, 5), GPIO_INPUT) -GPIO(CCD_MODE_ODL, PIN(C, 5), GPIO_INPUT | GPIO_PULL_UP) -GPIO(CHARGER_INT_L, PIN(E, 6), GPIO_INPUT | GPIO_PULL_UP) -/* Non-INT power signal pin */ -GPIO(AP_CORE_PG, PIN(D, 7), GPIO_INPUT | GPIO_PULL_UP) - - - -/* Other output pins */ -GPIO(ENTERING_RW, PIN(C, 6), GPIO_ODR_HIGH) -GPIO(SYS_RST_L, PIN(C, 8), GPIO_ODR_HIGH) -GPIO(EC_INT_L, PIN(E, 3), GPIO_ODR_HIGH) -GPIO(EC_BOARD_ID_EN_L, PIN(F, 1), GPIO_ODR_HIGH) -GPIO(USB_C0_DISCHARGE, PIN(A, 11), GPIO_OUT_LOW) -GPIO(PCA9468_EN, PIN(E, 15), GPIO_OUT_LOW) - -/* USART1: PA9/PA10 */ -ALTERNATE(PIN_MASK(A, 0x0600), 1, MODULE_UART, 0) -/* I2C MASTER: PB8/9 */ -ALTERNATE(PIN_MASK(B, 0x0300), 1, MODULE_I2C, 0) -/* I2C MASTER: PB10/11 */ -ALTERNATE(PIN_MASK(B, 0x0c00), 1, MODULE_I2C, 0) -/* SPI SLAVE: PB3/4/5 */ -ALTERNATE(PIN_MASK(B, 0x0038), 0, MODULE_SPI, 0) -/* SPI SLAVE CS: PA15 */ -ALTERNATE(PIN_MASK(A, 0x8000), 0, MODULE_SPI, 0) -/* SPI MASTER: PD1/3/4 */ -ALTERNATE(PIN_MASK(D, 0x001a), 1, MODULE_SPI_CONTROLLER, 0) diff --git a/board/rainier/usb_pd_policy.c b/board/rainier/usb_pd_policy.c deleted file mode 100644 index 6de1dc9271..0000000000 --- a/board/rainier/usb_pd_policy.c +++ /dev/null @@ -1,66 +0,0 @@ -/* Copyright 2017 The Chromium OS Authors. All rights reserved. - * Use of this source code is governed by a BSD-style license that can be - * found in the LICENSE file. - */ - -#include "atomic.h" -#include "common.h" -#include "console.h" -#include "gpio.h" -#include "hooks.h" -#include "host_command.h" -#include "registers.h" -#include "system.h" -#include "task.h" -#include "timer.h" -#include "util.h" -#include "usb_mux.h" -#include "usb_pd.h" -#include "usb_pd_tcpm.h" - -#define CPRINTF(format, args...) cprintf(CC_USBPD, format, ## args) -#define CPRINTS(format, args...) cprints(CC_USBPD, format, ## args) - -static uint8_t vbus_en; - -int board_vbus_source_enabled(int port) -{ - return vbus_en; -} - -int pd_set_power_supply_ready(int port) -{ - pd_set_vbus_discharge(port, 0); - /* Provide VBUS */ - vbus_en = 1; - - /* notify host of power info change */ - pd_send_host_event(PD_EVENT_POWER_CHANGE); - - return EC_SUCCESS; /* we are ready */ -} - -void pd_power_supply_reset(int port) -{ - int prev_en; - - prev_en = vbus_en; - /* Disable VBUS */ - vbus_en = 0; - - /* Enable discharge if we were previously sourcing 5V */ - if (prev_en) - pd_set_vbus_discharge(port, 1); - - /* notify host of power info change */ - pd_send_host_event(PD_EVENT_POWER_CHANGE); -} - -int pd_check_vconn_swap(int port) -{ - /* - * VCONN is provided directly by the battery (PPVAR_SYS) - * but use the same rules as power swap. - */ - return pd_get_dual_role(port) == PD_DRP_TOGGLE_ON ? 1 : 0; -} diff --git a/board/rainier/vif_override.xml b/board/rainier/vif_override.xml deleted file mode 100644 index 32736caf64..0000000000 --- a/board/rainier/vif_override.xml +++ /dev/null @@ -1,3 +0,0 @@ -<!-- Add VIF field overrides here. See genvif.c and the Vendor Info File - Definition from the USB-IF. ---> |