diff options
Diffstat (limited to 'board/sasuke/board.h')
| -rw-r--r-- | board/sasuke/board.h | 167 |
1 files changed, 0 insertions, 167 deletions
diff --git a/board/sasuke/board.h b/board/sasuke/board.h deleted file mode 100644 index 4d70cda5ab..0000000000 --- a/board/sasuke/board.h +++ /dev/null @@ -1,167 +0,0 @@ -/* Copyright 2020 The Chromium OS Authors. All rights reserved. - * Use of this source code is governed by a BSD-style license that can be - * found in the LICENSE file. - */ - -/* Waddledoo board configuration */ - -#ifndef __CROS_EC_BOARD_H -#define __CROS_EC_BOARD_H - -#define VARIANT_DEDEDE_EC_NPCX796FC -#include "baseboard.h" -#undef GPIO_VOLUME_UP_L -#undef GPIO_VOLUME_DOWN_L -#undef CONFIG_VOLUME_BUTTONS - -/* EC console commands */ -#define CONFIG_CMD_TCPC_DUMP -#define CONFIG_CMD_CHARGER_DUMP - -/* Battery */ -#define CONFIG_BATTERY_FUEL_GAUGE - -/* Charger */ -#define CONFIG_CHARGER_RAA489000 -#define CONFIG_CHARGER_SENSE_RESISTOR_AC 10 -#define CONFIG_CHARGER_SENSE_RESISTOR 10 -#define CONFIG_OCPC_DEF_RBATT_MOHMS 22 /* R_DS(on) 11.6mOhm + 10mOhm sns rstr */ -#define CONFIG_OCPC -#define CONFIG_CHARGER_PROFILE_OVERRIDE -#define CONFIG_CHARGE_RAMP_HW -#undef CONFIG_CHARGER_SINGLE_CHIP - -#define CONFIG_BATTERY_CHECK_CHARGE_TEMP_LIMITS - -/* - * GPIO for C1 interrupts, for baseboard use - * - * Note this line might already have its pull up disabled for HDMI DBs, but - * it should be fine to set again before z-state. - */ -#define GPIO_USB_C1_INT_ODL GPIO_SUB_C1_INT_EN_RAILS_ODL - -/* Keyboard */ - -/* LED */ -#define CONFIG_LED_COMMON -#define CONFIG_LED_ONOFF_STATES -#define GPIO_BAT_LED_RED_L GPIO_LED_R_ODL -#define GPIO_BAT_LED_GREEN_L GPIO_LED_G_ODL -#define GPIO_PWR_LED_BLUE_L GPIO_LED_B_ODL - - -/* PWM */ -#define NPCX7_PWM1_SEL 0 /* GPIO C2 is not used as PWM1. */ - -/* Thermistors */ -#define CONFIG_TEMP_SENSOR -#define CONFIG_THERMISTOR -#define CONFIG_STEINHART_HART_3V3_51K1_47K_4050B - -/* USB */ -#define CONFIG_BC12_DETECT_PI3USB9201 -#define CONFIG_USBC_RETIMER_NB7V904M -#define CONFIG_USB_MUX_RUNTIME_CONFIG -#define CONFIG_USB_MUX_PS8743 - -/* USB PD */ -#define CONFIG_USB_PD_PORT_MAX_COUNT 2 -#define CONFIG_USB_PD_TCPM_RAA489000 -#undef CONFIG_USB_PD_TCPC_LPM_EXIT_DEBOUNCE -#define CONFIG_USB_PD_TCPC_LPM_EXIT_DEBOUNCE (100 * MSEC) -#define CONFIG_USB_PD_COMM_LOCKED - -/* USB defines specific to external TCPCs */ -#define CONFIG_USB_PD_DUAL_ROLE_AUTO_TOGGLE -#define CONFIG_USB_PD_VBUS_DETECT_TCPC -#define CONFIG_USB_PD_DISCHARGE_TCPC -#define CONFIG_USB_PD_TCPC_LOW_POWER - -/* Variant references the TCPCs to determine Vbus sourcing */ -#define CONFIG_USB_PD_5V_EN_CUSTOM - -#undef PD_POWER_SUPPLY_TURN_ON_DELAY -#undef PD_POWER_SUPPLY_TURN_OFF_DELAY -#undef CONFIG_USBC_VCONN_SWAP_DELAY_US -/* 20% margin added for these timings */ -#define PD_POWER_SUPPLY_TURN_ON_DELAY 13080 /* us */ -#define PD_POWER_SUPPLY_TURN_OFF_DELAY 16080 /* us */ -#undef CONFIG_USBC_VCONN_SWAP_DELAY_US -#define CONFIG_USBC_VCONN_SWAP_DELAY_US 787 /* us */ - -/* USB Type A Features */ -#define USB_PORT_COUNT 1 -#undef CONFIG_USB_PORT_POWER_SMART_PORT_COUNT -#define CONFIG_USB_PORT_POWER_SMART_PORT_COUNT 1 -#define CONFIG_USB_PORT_POWER_SMART -#define CONFIG_USB_PORT_POWER_SMART_CDP_SDP_ONLY -#define CONFIG_USB_PORT_POWER_SMART_DEFAULT_MODE USB_CHARGE_MODE_CDP -#define CONFIG_USB_PORT_POWER_SMART_INVERTED -#define GPIO_USB1_ILIM_SEL GPIO_EN_USB_A0_5V_SUB - -/* I2C configuration */ -#define I2C_PORT_EEPROM NPCX_I2C_PORT7_0 -#define I2C_PORT_BATTERY NPCX_I2C_PORT5_0 -#define I2C_PORT_SENSOR NPCX_I2C_PORT0_0 -#define I2C_PORT_USB_C0 NPCX_I2C_PORT1_0 -#define I2C_PORT_SUB_USB_C1 NPCX_I2C_PORT2_0 -#define I2C_PORT_USB_MUX I2C_PORT_USB_C0 -/* TODO(b:147440290): Need to handle multiple charger ICs */ -#define I2C_PORT_CHARGER I2C_PORT_USB_C0 - -#define I2C_PORT_ACCEL I2C_PORT_SENSOR - -#define I2C_ADDR_EEPROM_FLAGS 0x50 /* 7b address */ - -/* - * I2C pin names for baseboard - * - * Note: these lines will be set as i2c on start-up, but this should be - * okay since they're ODL. - */ -#define GPIO_EC_I2C_SUB_USB_C1_SCL GPIO_EC_I2C_SUB_C1_SCL_HDMI_EN_ODL -#define GPIO_EC_I2C_SUB_USB_C1_SDA GPIO_EC_I2C_SUB_C1_SDA_HDMI_HPD_ODL - -#define CONFIG_MATH_UTIL - -/* - * There is ccd connection issue on board id = 2. - * NB7V904M is needed to be active to resolve this. - */ -#define CONFIG_NB7V904M_LPM_OVERRIDE - -#ifndef __ASSEMBLER__ - -#include "gpio_signal.h" -#include "registers.h" - -enum chg_id { - CHARGER_PRIMARY, - CHARGER_SECONDARY, - CHARGER_NUM, -}; - -enum temp_sensor_id { - TEMP_SENSOR_1, - TEMP_SENSOR_2, - TEMP_SENSOR_COUNT -}; - -enum adc_channel { - ADC_TEMP_SENSOR_1, /* ADC0 */ - ADC_TEMP_SENSOR_2, /* ADC1 */ - ADC_SUB_ANALOG, /* ADC2 */ - ADC_VSNS_PP3300_A, /* ADC9 */ - ADC_CH_COUNT -}; - -/* List of possible batteries */ -enum battery_type { - BATTERY_SDI, - BATTERY_SWD, - BATTERY_TYPE_COUNT, -}; - -#endif /* !__ASSEMBLER__ */ -#endif /* __CROS_EC_BOARD_H */ |