diff options
Diffstat (limited to 'board/servo_v4/board.h')
| -rw-r--r-- | board/servo_v4/board.h | 277 |
1 files changed, 0 insertions, 277 deletions
diff --git a/board/servo_v4/board.h b/board/servo_v4/board.h deleted file mode 100644 index f932752ef4..0000000000 --- a/board/servo_v4/board.h +++ /dev/null @@ -1,277 +0,0 @@ -/* Copyright 2016 The Chromium OS Authors. All rights reserved. - * Use of this source code is governed by a BSD-style license that can be - * found in the LICENSE file. - */ - -/* Servo V4 configuration */ - -#ifndef __CROS_EC_BOARD_H -#define __CROS_EC_BOARD_H - -#define CONFIG_LTO - -/* Free up flash space */ -#ifdef SECTION_IS_RO -#define CONFIG_DEBUG_ASSERT_BRIEF -#endif - -/* - * Board Versions: - * Versions are designated by the PCB color and consist of red, blue, and - * black. Only the black version has pullup resistors to distinguish its board - * id from previous versions. - */ -#define BOARD_VERSION_BLACK 3 - -/* 48 MHz SYSCLK clock frequency */ -#define CPU_CLOCK 48000000 - -/* Enable USART1,3,4 and USB streams */ -#define CONFIG_STREAM_USART -#define CONFIG_STREAM_USART3 -#define CONFIG_STREAM_USART4 -#define CONFIG_STREAM_USB -#define CONFIG_CMD_USART_INFO - -/* Optional features */ -#define CONFIG_STM_HWTIMER32 -#define CONFIG_HW_CRC -#define CONFIG_PVD -/* See 'Programmable voltage detector characteristics' in the STM32F072x8 Datasheet. - PVD Threshold 1 corresponds to a falling voltage threshold of min:2.09V, max:2.27V. */ -#define PVD_THRESHOLD (1) - -/* USB Configuration */ -#define CONFIG_USB -#define CONFIG_USB_PID 0x501b -#define CONFIG_USB_CONSOLE -#define CONFIG_USB_UPDATE -#define CONFIG_USB_BCD_DEV 0x0001 /* v 0.01 */ - -#define CONFIG_USB_PD_IDENTITY_HW_VERS 1 -#define CONFIG_USB_PD_IDENTITY_SW_VERS 1 - -#define CONFIG_USB_SELF_POWERED - -#define CONFIG_USB_SERIALNO -#define DEFAULT_SERIALNO "Uninitialized" -#define CONFIG_MAC_ADDR -#define DEFAULT_MAC_ADDR "Uninitialized" - -/* USB interface indexes (use define rather than enum to expand them) */ -#define USB_IFACE_CONSOLE 0 -#define USB_IFACE_EMPTY 1 -#define USB_IFACE_I2C 2 -#define USB_IFACE_USART3_STREAM 3 -#define USB_IFACE_USART4_STREAM 4 -#define USB_IFACE_UPDATE 5 -#define USB_IFACE_COUNT 6 - -/* USB endpoint indexes (use define rather than enum to expand them) */ -#define USB_EP_CONTROL 0 -#define USB_EP_CONSOLE 1 -#define USB_EP_EMPTY 2 -#define USB_EP_I2C 3 -#define USB_EP_USART3_STREAM 4 -#define USB_EP_USART4_STREAM 5 -#define USB_EP_UPDATE 6 -#define USB_EP_COUNT 7 - -/* Enable console recasting of GPIO type. */ -#define CONFIG_CMD_GPIO_EXTENDED - -/* This is not actually an EC so disable some features. */ -#undef CONFIG_WATCHDOG_HELP -#undef CONFIG_LID_SWITCH -#undef CONFIG_HIBERNATE - -/* Remove console commands / features for flash / RAM savings */ -#undef CONFIG_USB_PD_HOST_CMD -#undef CONFIG_CONSOLE_CMDHELP -#undef CONFIG_CONSOLE_HISTORY -#undef CONFIG_CMD_CRASH -#undef CONFIG_CMD_ACCELSPOOF -#undef CONFIG_CMD_FASTCHARGE -#undef CONFIG_CMD_FLASHINFO -#undef CONFIG_CMD_FLASH_WP -#undef CONFIG_CMD_GETTIME -#undef CONFIG_CMD_MEM -#undef CONFIG_CMD_SHMEM -#undef CONFIG_CMD_SYSLOCK -#undef CONFIG_CMD_TIMERINFO -#undef CONFIG_CMD_WAITMS -#undef CONFIG_CMD_USART_INFO -#undef CONFIG_CMD_CHARGE_SUPPLIER_INFO - -/* Enable control of I2C over USB */ -#define CONFIG_USB_I2C -#define CONFIG_I2C -#define CONFIG_I2C_CONTROLLER -#define I2C_PORT_MASTER 1 - -/* PD features */ -#define CONFIG_ADC -#undef CONFIG_ADC_WATCHDOG -#define CONFIG_BOARD_PRE_INIT -/* - * If task profiling is enabled then the rx falling edge detection interrupts - * can't be processed in time and can't support USB PD messaging. - */ -#undef CONFIG_TASK_PROFILING - -#define CONFIG_CHARGE_MANAGER -#undef CONFIG_CHARGE_MANAGER_SAFE_MODE -#define CONFIG_USB_POWER_DELIVERY -#define CONFIG_USB_PD_TCPMV1 -#define CONFIG_CMD_PD -#define CONFIG_USB_PD_CUSTOM_PDO -#define CONFIG_USB_PD_ALT_MODE -#define CONFIG_USB_PD_DUAL_ROLE -#define CONFIG_USB_PD_DYNAMIC_SRC_CAP -#define CONFIG_USB_PD_INTERNAL_COMP -#define CONFIG_USB_PD_PORT_MAX_COUNT 2 -#define CONFIG_USB_PD_TCPC -#define CONFIG_USB_PD_TCPM_STUB -#undef CONFIG_USB_PD_PULLUP -#define CONFIG_USB_PD_PULLUP TYPEC_RP_USB -#define CONFIG_USB_PD_VBUS_MEASURE_NOT_PRESENT -#define CONFIG_USB_PD_ONLY_FIXED_PDOS - -/* Don't automatically change roles */ -#undef CONFIG_USB_PD_INITIAL_DRP_STATE -#define CONFIG_USB_PD_INITIAL_DRP_STATE PD_DRP_FORCE_SINK - -/* Variable-current Rp no connect and Ra attach macros */ -#define CC_NC(port, cc, sel) (pd_tcpc_cc_nc(port, cc, sel)) -#define CC_RA(port, cc, sel) (pd_tcpc_cc_ra(port, cc, sel)) - -/* - * TODO(crosbug.com/p/60792): The delay values are currently just place holders - * and the delay will need to be relative to the circuitry that allows VBUS to - * be supplied to the DUT port from the CHG port. - */ -#define PD_POWER_SUPPLY_TURN_ON_DELAY 50000 /* us */ -#define PD_POWER_SUPPLY_TURN_OFF_DELAY 50000 /* us */ - -/* Define typical operating power and max power */ -#define PD_OPERATING_POWER_MW 15000 -#define PD_MAX_POWER_MW 60000 -#define PD_MAX_CURRENT_MA 3000 -#define PD_MAX_VOLTAGE_MV 20000 -/* - * Define PDO selection logic for SourceCap. - * On a 45W PD charger, it might provide PDOs with 15V/3A and 20V/2.25A. - * In this case, pd_find_pdo_index() would always prefer 15V/3A rather than - * 20V/2.25A and such that the 20V PDO will be disappeared when servo-v4 - * advertise the SrcCap. We define PD_PREFER_HIGH_VOLTAGE so that all the - * PDOs could be advertised by servo-v4. - */ -#define PD_PREFER_HIGH_VOLTAGE - -/* - * Allow dangerous commands all the time, since we don't have a write protect - * switch. - */ -#define CONFIG_SYSTEM_UNLOCKED - -#ifndef __ASSEMBLER__ - -/* Timer selection */ -#define TIM_CLOCK32 2 -#define TIM_ADC 3 - - -#include "gpio_signal.h" - -/* USB string indexes */ -enum usb_strings { - USB_STR_DESC = 0, - USB_STR_VENDOR, - USB_STR_PRODUCT, - USB_STR_SERIALNO, - USB_STR_VERSION, - USB_STR_I2C_NAME, - USB_STR_CONSOLE_NAME, - USB_STR_USART3_STREAM_NAME, - USB_STR_USART4_STREAM_NAME, - USB_STR_UPDATE_NAME, - USB_STR_COUNT -}; - - -/* ADC signal */ -enum adc_channel { - ADC_CHG_CC1_PD, - ADC_CHG_CC2_PD, - ADC_DUT_CC1_PD, - ADC_DUT_CC2_PD, - ADC_SBU1_DET, - ADC_SBU2_DET, - ADC_SUB_C_REF, - /* Number of ADC channels */ - ADC_CH_COUNT -}; - -/** - * Compare cc_voltage to disconnect threshold - * - * This function can be used for boards that support variable Rp settings and - * require a different voltage threshold based on the Rp value attached to a - * given cc line. - * - * @param port USB-C port number - * @param cc_volt voltage measured in mV of the CC line - * @param cc_sel cc1 or cc2 selection - * @return 1 if voltage is >= threshold value for disconnect - */ -int pd_tcpc_cc_nc(int port, int cc_volt, int cc_sel); - -/** - * Compare cc_voltage to Ra threshold - * - * This function can be used for boards that support variable Rp settings and - * require a different voltage threshold based on the Rp value attached to a - * given cc line. - * - * @param port USB-C port number - * @param cc_volt voltage measured in mV of the CC line - * @param cc_sel cc1 or cc2 selection - * @return 1 if voltage is < threshold value for Ra attach - */ -int pd_tcpc_cc_ra(int port, int cc_volt, int cc_sel); - -/** - * Set Rp or Rd resistor for CC lines - * - * This function is used to configure the CC pullup or pulldown resistor to - * the requested value. - * - * @param port USB-C port number - * @param cc_pull 1 for Rp and 0 for Rd - * @param rp_value If cc_pull == 1, the value of Rp to use - * @return 1 if cc_pull == 1 and Rp is invalid, otherwise 0 - */ -int pd_set_rp_rd(int port, int cc_pull, int rp_value); - -/** - * Get board HW ID version - * - * @return HW ID version - */ -int board_get_version(void); - -/** - * Enable or disable external HPD detection - * - * @param enable Enable external HPD detection if true, otherwise disable - */ -void ext_hpd_detection_enable(int enable); - -/** - * Enable or disable CCD - * - * @param enable Enable CCD if true, otherwise disable - */ -void ccd_enable(int enable); -#endif /* !__ASSEMBLER__ */ -#endif /* __CROS_EC_BOARD_H */ |