diff options
Diffstat (limited to 'board/taeko/board.h')
| -rw-r--r-- | board/taeko/board.h | 151 |
1 files changed, 68 insertions, 83 deletions
diff --git a/board/taeko/board.h b/board/taeko/board.h index a6395ffc61..c3193c8847 100644 --- a/board/taeko/board.h +++ b/board/taeko/board.h @@ -1,4 +1,4 @@ -/* Copyright 2021 The Chromium OS Authors. All rights reserved. +/* Copyright 2021 The ChromiumOS Authors * Use of this source code is governed by a BSD-style license that can be * found in the LICENSE file. */ @@ -30,18 +30,17 @@ #define CONFIG_LED_ONOFF_STATES /* Sensors */ -#define CONFIG_DYNAMIC_MOTION_SENSOR_COUNT +#define CONFIG_DYNAMIC_MOTION_SENSOR_COUNT /* Button */ #define CONFIG_BUTTONS_RUNTIME_CONFIG - /* Change Request (b/199529373) * GYRO sensor change from ST LSM6DSOETR3TR to ST LSM6DS3TR-C * LSM6DSOETR3TR base accel/gyro if board id = 0 * LSM6DS3TR-C Base accel/gyro if board id > 0 */ -#define CONFIG_ACCELGYRO_LSM6DSO /* Base accel */ +#define CONFIG_ACCELGYRO_LSM6DSO /* Base accel */ #define CONFIG_ACCEL_LSM6DSO_INT_EVENT \ TASK_EVENT_MOTION_SENSOR_INTERRUPT(BASE_ACCEL) #define CONFIG_ACCELGYRO_LSM6DSM @@ -56,14 +55,13 @@ #define CONFIG_ACCEL_FIFO_THRES (CONFIG_ACCEL_FIFO_SIZE / 3) /* Sensors without hardware FIFO are in forced mode */ -#define CONFIG_ACCEL_FORCE_MODE_MASK \ - (BIT(LID_ACCEL)) +#define CONFIG_ACCEL_FORCE_MODE_MASK (BIT(LID_ACCEL)) /* Lid accel */ #define CONFIG_LID_ANGLE #define CONFIG_LID_ANGLE_UPDATE -#define CONFIG_LID_ANGLE_SENSOR_BASE BASE_ACCEL -#define CONFIG_LID_ANGLE_SENSOR_LID LID_ACCEL +#define CONFIG_LID_ANGLE_SENSOR_BASE BASE_ACCEL +#define CONFIG_LID_ANGLE_SENSOR_LID LID_ACCEL #define CONFIG_ACCEL_BMA4XX #define CONFIG_ACCEL_LIS2DWL @@ -72,7 +70,7 @@ #define CONFIG_CMD_ACCEL_INFO /* USB Type A Features */ -#define USB_PORT_COUNT 1 +#define USB_PORT_COUNT 1 #define CONFIG_USB_PORT_POWER_DUMB /* USB Type C and USB PD defines */ @@ -80,7 +78,7 @@ #define CONFIG_IO_EXPANDER #define CONFIG_IO_EXPANDER_NCT38XX -#define CONFIG_IO_EXPANDER_PORT_COUNT 1 +#define CONFIG_IO_EXPANDER_PORT_COUNT 1 #define CONFIG_USB_PD_FRS_PPC #define CONFIG_USB_PD_FRS @@ -88,6 +86,7 @@ #define CONFIG_USB_PD_TCPM_PS8815_FORCE_DID #define CONFIG_USBC_PPC_SYV682X #define CONFIG_USBC_PPC_NX20P3483 +#define CONFIG_USBC_NX20P348X_RCP_5VSRC_MASK_ENABLE /* I2C speed console command */ #define CONFIG_CMD_I2C_SPEED @@ -96,76 +95,77 @@ #define CONFIG_HOSTCMD_I2C_CONTROL /* TODO: b/177608416 - measure and check these values on brya */ -#define PD_POWER_SUPPLY_TURN_ON_DELAY 30000 /* us */ -#define PD_POWER_SUPPLY_TURN_OFF_DELAY 30000 /* us */ -#define PD_VCONN_SWAP_DELAY 5000 /* us */ +#define PD_POWER_SUPPLY_TURN_ON_DELAY 30000 /* us */ +#define PD_POWER_SUPPLY_TURN_OFF_DELAY 30000 /* us */ +#define PD_VCONN_SWAP_DELAY 5000 /* us */ /* * Passive USB-C cables only support up to 60W. */ -#define PD_OPERATING_POWER_MW 15000 -#define PD_MAX_POWER_MW 45000 -#define PD_MAX_CURRENT_MA 3000 -#define PD_MAX_VOLTAGE_MV 20000 +#define PD_OPERATING_POWER_MW 15000 +#define PD_MAX_POWER_MW 45000 +#define PD_MAX_CURRENT_MA 3000 +#define PD_MAX_VOLTAGE_MV 20000 /* The lower the input voltage, the higher the power efficiency. */ #define PD_PREFER_LOW_VOLTAGE +#undef CONFIG_CMD_POWERINDEBUG + /* * Macros for GPIO signals used in common code that don't match the * schematic names. Signal names in gpio.inc match the schematic and are * then redefined here to so it's more clear which signal is being used for * which purpose. */ -#define GPIO_AC_PRESENT GPIO_ACOK_OD -#define GPIO_CPU_PROCHOT GPIO_EC_PROCHOT_ODL -#define GPIO_EC_INT_L GPIO_EC_PCH_INT_ODL -#define GPIO_ENABLE_BACKLIGHT GPIO_EC_EN_EDP_BL -#define GPIO_ENTERING_RW GPIO_EC_ENTERING_RW -#define GPIO_KBD_KSO2 GPIO_EC_KSO_02_INV -#define GPIO_PACKET_MODE_EN GPIO_EC_GSC_PACKET_MODE -#define GPIO_PCH_PWRBTN_L GPIO_EC_PCH_PWR_BTN_ODL -#define GPIO_PCH_RSMRST_L GPIO_EC_PCH_RSMRST_L -#define GPIO_PCH_RTCRST GPIO_EC_PCH_RTCRST -#define GPIO_PCH_SLP_S0_L GPIO_SYS_SLP_S0IX_L -#define GPIO_PCH_SLP_S3_L GPIO_SLP_S3_L -#define GPIO_TEMP_SENSOR_POWER GPIO_SEQ_EC_DSW_PWROK +#define GPIO_AC_PRESENT GPIO_ACOK_OD +#define GPIO_CPU_PROCHOT GPIO_EC_PROCHOT_ODL +#define GPIO_EC_INT_L GPIO_EC_PCH_INT_ODL +#define GPIO_ENABLE_BACKLIGHT GPIO_EC_EN_EDP_BL +#define GPIO_ENTERING_RW GPIO_EC_ENTERING_RW +#define GPIO_KBD_KSO2 GPIO_EC_KSO_02_INV +#define GPIO_PACKET_MODE_EN GPIO_EC_GSC_PACKET_MODE +#define GPIO_PCH_PWRBTN_L GPIO_EC_PCH_PWR_BTN_ODL +#define GPIO_PCH_RSMRST_L GPIO_EC_PCH_RSMRST_L +#define GPIO_PCH_RTCRST GPIO_EC_PCH_RTCRST +#define GPIO_PCH_SLP_S0_L GPIO_SYS_SLP_S0IX_L +#define GPIO_PCH_SLP_S3_L GPIO_SLP_S3_L +#define GPIO_TEMP_SENSOR_POWER GPIO_SEQ_EC_DSW_PWROK /* * GPIO_EC_PCH_INT_ODL is used for MKBP events as well as a PCH wakeup * signal. */ -#define GPIO_PCH_WAKE_L GPIO_EC_PCH_INT_ODL -#define GPIO_PG_EC_ALL_SYS_PWRGD GPIO_SEQ_EC_ALL_SYS_PG -#define GPIO_PG_EC_DSW_PWROK GPIO_SEQ_EC_DSW_PWROK -#define GPIO_PG_EC_RSMRST_ODL GPIO_SEQ_EC_RSMRST_ODL -#define GPIO_POWER_BUTTON_L GPIO_GSC_EC_PWR_BTN_ODL -#define GPIO_SYS_RESET_L GPIO_SYS_RST_ODL -#define GPIO_VOLUME_DOWN_L GPIO_EC_VOLDN_BTN_ODL -#define GPIO_VOLUME_UP_L GPIO_EC_VOLUP_BTN_ODL -#define GPIO_WP_L GPIO_EC_WP_ODL +#define GPIO_PCH_WAKE_L GPIO_EC_PCH_INT_ODL +#define GPIO_PG_EC_ALL_SYS_PWRGD GPIO_SEQ_EC_ALL_SYS_PG +#define GPIO_PG_EC_DSW_PWROK GPIO_SEQ_EC_DSW_PWROK +#define GPIO_PG_EC_RSMRST_ODL GPIO_SEQ_EC_RSMRST_ODL +#define GPIO_POWER_BUTTON_L GPIO_GSC_EC_PWR_BTN_ODL +#define GPIO_SYS_RESET_L GPIO_SYS_RST_ODL +#define GPIO_VOLUME_DOWN_L GPIO_EC_VOLDN_BTN_ODL +#define GPIO_VOLUME_UP_L GPIO_EC_VOLUP_BTN_ODL +#define GPIO_WP_L GPIO_EC_WP_ODL /* System has back-lit keyboard */ #define CONFIG_PWM_KBLIGHT - /* I2C Bus Configuration */ -#define I2C_PORT_SENSOR NPCX_I2C_PORT0_0 -#define I2C_PORT_USB_C0_TCPC NPCX_I2C_PORT1_0 -#define I2C_PORT_USB_C1_TCPC NPCX_I2C_PORT4_1 -#define I2C_PORT_USB_C0_PPC NPCX_I2C_PORT2_0 -#define I2C_PORT_USB_C1_PPC NPCX_I2C_PORT6_1 -#define I2C_PORT_USB_C0_BC12 NPCX_I2C_PORT2_0 -#define I2C_PORT_USB_C1_BC12 NPCX_I2C_PORT6_1 -#define I2C_PORT_USB_C1_MUX NPCX_I2C_PORT6_1 -#define I2C_PORT_BATTERY NPCX_I2C_PORT5_0 -#define I2C_PORT_CHARGER NPCX_I2C_PORT7_0 -#define I2C_PORT_EEPROM NPCX_I2C_PORT7_0 -#define I2C_PORT_MP2964 NPCX_I2C_PORT7_0 - -#define I2C_ADDR_EEPROM_FLAGS 0x50 - -#define I2C_ADDR_MP2964_FLAGS 0x20 +#define I2C_PORT_SENSOR NPCX_I2C_PORT0_0 +#define I2C_PORT_USB_C0_TCPC NPCX_I2C_PORT1_0 +#define I2C_PORT_USB_C1_TCPC NPCX_I2C_PORT4_1 +#define I2C_PORT_USB_C0_PPC NPCX_I2C_PORT2_0 +#define I2C_PORT_USB_C1_PPC NPCX_I2C_PORT6_1 +#define I2C_PORT_USB_C0_BC12 NPCX_I2C_PORT2_0 +#define I2C_PORT_USB_C1_BC12 NPCX_I2C_PORT6_1 +#define I2C_PORT_USB_C1_MUX NPCX_I2C_PORT6_1 +#define I2C_PORT_BATTERY NPCX_I2C_PORT5_0 +#define I2C_PORT_CHARGER NPCX_I2C_PORT7_0 +#define I2C_PORT_EEPROM NPCX_I2C_PORT7_0 +#define I2C_PORT_MP2964 NPCX_I2C_PORT7_0 + +#define I2C_ADDR_EEPROM_FLAGS 0x50 + +#define I2C_ADDR_MP2964_FLAGS 0x20 /* Thermal features */ #define CONFIG_THERMISTOR @@ -174,16 +174,16 @@ #define CONFIG_STEINHART_HART_3V3_30K9_47K_4050B /* Fan */ -#define CONFIG_FANS FAN_CH_COUNT +#define CONFIG_FANS FAN_CH_COUNT /* Charger defines */ #define CONFIG_CHARGER_BQ25720 #define CONFIG_CHARGER_BQ25720_VSYS_TH2_CUSTOM /* 37h BIT7:2 VSYS_TH2 6.0V */ -#define CONFIG_CHARGER_BQ25720_VSYS_TH2_DV 60 +#define CONFIG_CHARGER_BQ25720_VSYS_TH2_DV 60 #define CONFIG_CHARGE_RAMP_SW -#define CONFIG_CHARGER_BQ25710_SENSE_RESISTOR 10 -#define CONFIG_CHARGER_BQ25710_SENSE_RESISTOR_AC 10 +#define CONFIG_CHARGER_BQ25710_SENSE_RESISTOR 10 +#define CONFIG_CHARGER_BQ25710_SENSE_RESISTOR_AC 10 /* 30h BIT13:12 Enable PSYS 00b */ #define CONFIG_CHARGER_BQ25710_PSYS_SENSING /* 31h BIT3 = 1 Enable ACOC */ @@ -200,15 +200,14 @@ #define CONFIG_CHARGER_BQ25710_PP_COMP /* 36h UVP 5600mV */ #define CONFIG_CHARGER_BQ25720_VSYS_UVP_CUSTOM -#define CONFIG_CHARGER_BQ25720_VSYS_UVP \ - BQ25720_CHARGE_OPTION_4_VSYS_UVP__5P6 +#define CONFIG_CHARGER_BQ25720_VSYS_UVP BQ25720_CHARGE_OPTION_4_VSYS_UVP__5P6 /* 3Eh BIT15:8 VSYS_MIN 6.1V */ #define CONFIG_CHARGER_BQ25710_VSYS_MIN_VOLTAGE_CUSTOM #define CONFIG_CHARGER_BQ25710_VSYS_MIN_VOLTAGE_MV 6100 #ifndef __ASSEMBLER__ -#include "gpio_signal.h" /* needed by registers.h */ +#include "gpio_signal.h" /* needed by registers.h */ #include "registers.h" #include "usbc_config.h" @@ -228,17 +227,9 @@ enum temp_sensor_id { TEMP_SENSOR_COUNT }; -enum sensor_id { - LID_ACCEL = 0, - BASE_ACCEL, - BASE_GYRO, - SENSOR_COUNT -}; +enum sensor_id { LID_ACCEL = 0, BASE_ACCEL, BASE_GYRO, SENSOR_COUNT }; -enum ioex_port { - IOEX_C0_NCT38XX = 0, - IOEX_PORT_COUNT -}; +enum ioex_port { IOEX_C0_NCT38XX = 0, IOEX_PORT_COUNT }; enum battery_type { BATTERY_SMP_51W, @@ -249,20 +240,14 @@ enum battery_type { }; enum pwm_channel { - PWM_CH_KBLIGHT = 0, /* PWM3 */ - PWM_CH_FAN, /* PWM5 */ + PWM_CH_KBLIGHT = 0, /* PWM3 */ + PWM_CH_FAN, /* PWM5 */ PWM_CH_COUNT }; -enum fan_channel { - FAN_CH_0 = 0, - FAN_CH_COUNT -}; +enum fan_channel { FAN_CH_0 = 0, FAN_CH_COUNT }; -enum mft_channel { - MFT_CH_0 = 0, - MFT_CH_COUNT -}; +enum mft_channel { MFT_CH_0 = 0, MFT_CH_COUNT }; void motion_interrupt(enum gpio_signal signal); |