diff options
Diffstat (limited to 'board/taeko/board.h')
| -rw-r--r-- | board/taeko/board.h | 234 |
1 files changed, 0 insertions, 234 deletions
diff --git a/board/taeko/board.h b/board/taeko/board.h deleted file mode 100644 index 7b7995f001..0000000000 --- a/board/taeko/board.h +++ /dev/null @@ -1,234 +0,0 @@ -/* Copyright 2021 The Chromium OS Authors. All rights reserved. - * Use of this source code is governed by a BSD-style license that can be - * found in the LICENSE file. - */ - -/* Taeko board configuration */ - -#ifndef __CROS_EC_BOARD_H -#define __CROS_EC_BOARD_H - -#include "compile_time_macros.h" - -/* - * Taeko boards are set up for vivaldi - */ -#define CONFIG_KEYBOARD_VIVALDI - -/* Baseboard features */ -#include "baseboard.h" - -#define CONFIG_SYSTEM_UNLOCKED - -/* - * This will happen automatically on NPCX9 ES2 and later. Do not remove - * until we can confirm all earlier chips are out of service. - */ -#define CONFIG_HIBERNATE_PSL_VCC1_RST_WAKEUP - -#define CONFIG_MP2964 - -/* LED */ -#define CONFIG_LED_ONOFF_STATES - -/* Sensors */ - -/* TODO(b/194765820) - * Check if project support dynamic motion sensor count - */ -/* #define CONFIG_DYNAMIC_MOTION_SENSOR_COUNT */ - -#define CONFIG_ACCELGYRO_LSM6DSO /* Base accel */ -#define CONFIG_ACCEL_LSM6DSO_INT_EVENT \ - TASK_EVENT_MOTION_SENSOR_INTERRUPT(BASE_ACCEL) - -/* Enable sensor fifo, must also define the _SIZE and _THRES */ -#define CONFIG_ACCEL_FIFO -/* FIFO size is in power of 2. */ -#define CONFIG_ACCEL_FIFO_SIZE 256 -/* Depends on how fast the AP boots and typical ODRs */ -#define CONFIG_ACCEL_FIFO_THRES (CONFIG_ACCEL_FIFO_SIZE / 3) - -/* Sensors without hardware FIFO are in forced mode */ -#define CONFIG_ACCEL_FORCE_MODE_MASK \ - (BIT(LID_ACCEL)) - -/* Lid accel */ -#define CONFIG_LID_ANGLE -#define CONFIG_LID_ANGLE_SENSOR_BASE BASE_ACCEL -#define CONFIG_LID_ANGLE_SENSOR_LID LID_ACCEL -#define CONFIG_ACCEL_BMA4XX -#define CONFIG_ACCEL_LIS2DWL -#define CONFIG_ACCEL_LIS2DW_AS_BASE -#define CONFIG_ACCEL_LIS2DW12_INT_EVENT \ - TASK_EVENT_MOTION_SENSOR_INTERRUPT(LID_ACCEL) - -#define CONFIG_ACCEL_INTERRUPTS - -/* Sensor console commands */ -#define CONFIG_CMD_ACCELS -#define CONFIG_CMD_ACCEL_INFO - -/* USB Type A Features */ -#define USB_PORT_COUNT 1 -#define CONFIG_USB_PORT_POWER_DUMB - -/* USB Type C and USB PD defines */ -#define CONFIG_USB_PD_REQUIRE_AP_MODE_ENTRY - -#define CONFIG_IO_EXPANDER -#define CONFIG_IO_EXPANDER_NCT38XX -#define CONFIG_IO_EXPANDER_PORT_COUNT 1 - -#define CONFIG_USB_PD_TCPM_PS8815 - -#define CONFIG_USBC_PPC_SYV682X -#define CONFIG_USBC_PPC_NX20P3483 - -/* TODO: b/177608416 - measure and check these values on brya */ -#define PD_POWER_SUPPLY_TURN_ON_DELAY 30000 /* us */ -#define PD_POWER_SUPPLY_TURN_OFF_DELAY 30000 /* us */ -#define PD_VCONN_SWAP_DELAY 5000 /* us */ - -/* - * Passive USB-C cables only support up to 60W. - */ -#define PD_OPERATING_POWER_MW 15000 -#define PD_MAX_POWER_MW 60000 -#define PD_MAX_CURRENT_MA 3000 -#define PD_MAX_VOLTAGE_MV 20000 - -/* - * Macros for GPIO signals used in common code that don't match the - * schematic names. Signal names in gpio.inc match the schematic and are - * then redefined here to so it's more clear which signal is being used for - * which purpose. - */ -#define GPIO_AC_PRESENT GPIO_ACOK_OD -#define GPIO_CPU_PROCHOT GPIO_EC_PROCHOT_ODL -#define GPIO_EC_INT_L GPIO_EC_PCH_INT_ODL -#define GPIO_ENABLE_BACKLIGHT GPIO_EC_EN_EDP_BL -#define GPIO_ENTERING_RW GPIO_EC_ENTERING_RW -#define GPIO_KBD_KSO2 GPIO_EC_KSO_02_INV -#define GPIO_PACKET_MODE_EN GPIO_EC_GSC_PACKET_MODE -#define GPIO_PCH_PWRBTN_L GPIO_EC_PCH_PWR_BTN_ODL -#define GPIO_PCH_RSMRST_L GPIO_EC_PCH_RSMRST_L -#define GPIO_PCH_RTCRST GPIO_EC_PCH_RTCRST -#define GPIO_PCH_SLP_S0_L GPIO_SYS_SLP_S0IX_L -#define GPIO_PCH_SLP_S3_L GPIO_SLP_S3_L -#define GMR_TABLET_MODE_GPIO_L GPIO_TABLET_MODE_L - -/* - * GPIO_EC_PCH_INT_ODL is used for MKBP events as well as a PCH wakeup - * signal. - */ -#define GPIO_PCH_WAKE_L GPIO_EC_PCH_INT_ODL -#define GPIO_PG_EC_ALL_SYS_PWRGD GPIO_SEQ_EC_ALL_SYS_PG -#define GPIO_PG_EC_DSW_PWROK GPIO_SEQ_EC_DSW_PWROK -#define GPIO_PG_EC_RSMRST_ODL GPIO_SEQ_EC_RSMRST_ODL -#define GPIO_POWER_BUTTON_L GPIO_GSC_EC_PWR_BTN_ODL -#define GPIO_RSMRST_L_PGOOD GPIO_SEQ_EC_RSMRST_ODL -#define GPIO_SYS_RESET_L GPIO_SYS_RST_ODL -#define GPIO_VOLUME_DOWN_L GPIO_EC_VOLDN_BTN_ODL -#define GPIO_VOLUME_UP_L GPIO_EC_VOLUP_BTN_ODL -#define GPIO_WP_L GPIO_EC_WP_ODL - -/* System has back-lit keyboard */ -#define CONFIG_PWM_KBLIGHT - -/* I2C Bus Configuration */ -#define I2C_PORT_SENSOR NPCX_I2C_PORT0_0 -#define I2C_PORT_USB_C0_TCPC NPCX_I2C_PORT1_0 -#define I2C_PORT_USB_C1_TCPC NPCX_I2C_PORT4_1 -#define I2C_PORT_USB_C0_PPC NPCX_I2C_PORT2_0 -#define I2C_PORT_USB_C1_PPC NPCX_I2C_PORT6_1 -#define I2C_PORT_USB_C0_BC12 NPCX_I2C_PORT2_0 -#define I2C_PORT_USB_C1_BC12 NPCX_I2C_PORT6_1 -#define I2C_PORT_USB_C1_MUX NPCX_I2C_PORT6_1 -#define I2C_PORT_BATTERY NPCX_I2C_PORT5_0 -#define I2C_PORT_CHARGER NPCX_I2C_PORT7_0 -#define I2C_PORT_EEPROM NPCX_I2C_PORT7_0 -#define I2C_PORT_MP2964 NPCX_I2C_PORT7_0 - -#define I2C_ADDR_EEPROM_FLAGS 0x50 - -#define I2C_ADDR_MP2964_FLAGS 0x20 - -/* Thermal features */ -#define CONFIG_THERMISTOR -#define CONFIG_TEMP_SENSOR -#define CONFIG_TEMP_SENSOR_POWER_GPIO GPIO_SEQ_EC_DSW_PWROK -#define CONFIG_STEINHART_HART_3V3_30K9_47K_4050B - -/* Fan */ -#define CONFIG_FANS FAN_CH_COUNT - -/* Charger defines */ -#define CONFIG_CHARGER_BQ25720 -#define CONFIG_CHARGER_BQ25720_VSYS_TH2_DV 70 -#define CONFIG_CHARGE_RAMP_SW -#define CONFIG_CHARGER_SENSE_RESISTOR 10 -#define CONFIG_CHARGER_SENSE_RESISTOR_AC 10 - -#ifndef __ASSEMBLER__ - -#include "gpio_signal.h" /* needed by registers.h */ -#include "registers.h" -#include "usbc_config.h" - -enum adc_channel { - ADC_TEMP_SENSOR_1_DDR_SOC, - ADC_TEMP_SENSOR_2_FAN, - ADC_TEMP_SENSOR_3_CHARGER, - ADC_TEMP_SENSOR_4_CPUCHOKE, - ADC_CH_COUNT -}; - -enum temp_sensor_id { - TEMP_SENSOR_1_DDR_SOC, - TEMP_SENSOR_2_FAN, - TEMP_SENSOR_3_CHARGER, - TEMP_SENSOR_4_CPUCHOKE, - TEMP_SENSOR_COUNT -}; - -enum sensor_id { - LID_ACCEL = 0, - BASE_ACCEL, - BASE_GYRO, - SENSOR_COUNT -}; - -enum ioex_port { - IOEX_C0_NCT38XX = 0, - IOEX_PORT_COUNT -}; - -enum battery_type { - BATTERY_SMP, - BATTERY_LGC, - BATTERY_SUNWODA, - BATTERY_TYPE_COUNT, -}; - -enum pwm_channel { - PWM_CH_KBLIGHT = 0, /* PWM3 */ - PWM_CH_FAN, /* PWM5 */ - PWM_CH_COUNT -}; - -enum fan_channel { - FAN_CH_0 = 0, - FAN_CH_COUNT -}; - -enum mft_channel { - MFT_CH_0 = 0, - MFT_CH_COUNT -}; - -void motion_interrupt(enum gpio_signal signal); - -#endif /* !__ASSEMBLER__ */ - -#endif /* __CROS_EC_BOARD_H */ |