diff options
Diffstat (limited to 'board/trembyle')
| l--------- | board/trembyle/analyzestack.yaml | 1 | ||||
| -rw-r--r-- | board/trembyle/battery.c | 65 | ||||
| -rw-r--r-- | board/trembyle/board.c | 530 | ||||
| -rw-r--r-- | board/trembyle/board.h | 218 | ||||
| -rw-r--r-- | board/trembyle/build.mk | 15 | ||||
| -rw-r--r-- | board/trembyle/ec.tasklist | 26 | ||||
| -rw-r--r-- | board/trembyle/gpio.inc | 141 | ||||
| -rw-r--r-- | board/trembyle/led.c | 71 | ||||
| -rw-r--r-- | board/trembyle/vif_override.xml | 3 |
9 files changed, 0 insertions, 1070 deletions
diff --git a/board/trembyle/analyzestack.yaml b/board/trembyle/analyzestack.yaml deleted file mode 120000 index 4c09084128..0000000000 --- a/board/trembyle/analyzestack.yaml +++ /dev/null @@ -1 +0,0 @@ -../../baseboard/zork/analyzestack.yaml
\ No newline at end of file diff --git a/board/trembyle/battery.c b/board/trembyle/battery.c deleted file mode 100644 index 33e4e9ce5d..0000000000 --- a/board/trembyle/battery.c +++ /dev/null @@ -1,65 +0,0 @@ -/* Copyright 2019 The Chromium OS Authors. All rights reserved. - * Use of this source code is governed by a BSD-style license that can be - * found in the LICENSE file. - * - * Battery pack vendor provided charging profile - */ - -#include "battery_fuel_gauge.h" -#include "common.h" -#include "util.h" - -/* - * Battery info for all Zork battery types. Note that the fields - * start_charging_min/max and charging_min/max are not used for the charger. - * The effective temperature limits are given by discharging_min/max_c. - * - * Fuel Gauge (FG) parameters which are used for determining if the battery - * is connected, the appropriate ship mode (battery cutoff) command, and the - * charge/discharge FETs status. - * - * Ship mode (battery cutoff) requires 2 writes to the appropriate smart battery - * register. For some batteries, the charge/discharge FET bits are set when - * charging/discharging is active, in other types, these bits set mean that - * charging/discharging is disabled. Therefore, in addition to the mask for - * these bits, a disconnect value must be specified. Note that for TI fuel - * gauge, the charge/discharge FET status is found in Operation Status (0x54), - * but a read of Manufacturer Access (0x00) will return the lower 16 bits of - * Operation status which contains the FET status bits. - * - * The assumption for battery types supported is that the charge/discharge FET - * status can be read with a sb_read() command and therefore, only the register - * address, mask, and disconnect value need to be provided. - */ -const struct board_batt_params board_battery_info[] = { - /* AP18F4M */ - [BATTERY_AP18F4M] = { - .fuel_gauge = { - .manuf_name = "Murata KT00404001", - .ship_mode = { - .reg_addr = 0x3A, - .reg_data = { 0xC574, 0xC574 }, - }, - .fet = { - .reg_addr = 0x0, - .reg_mask = 0x2000, - .disconnect_val = 0x2000, - } - }, - .batt_info = { - .voltage_max = 8700, - .voltage_normal = 7600, - .voltage_min = 5500, - .precharge_current = 256, - .start_charging_min_c = 0, - .start_charging_max_c = 50, - .charging_min_c = 0, - .charging_max_c = 60, - .discharging_min_c = -20, - .discharging_max_c = 75, - }, - }, -}; -BUILD_ASSERT(ARRAY_SIZE(board_battery_info) == BATTERY_TYPE_COUNT); - -const enum battery_type DEFAULT_BATTERY_TYPE = BATTERY_AP18F4M; diff --git a/board/trembyle/board.c b/board/trembyle/board.c deleted file mode 100644 index 89a62f3411..0000000000 --- a/board/trembyle/board.c +++ /dev/null @@ -1,530 +0,0 @@ -/* Copyright 2019 The Chromium OS Authors. All rights reserved. - * Use of this source code is governed by a BSD-style license that can be - * found in the LICENSE file. - */ - -/* Trembyle board configuration */ - -#include "adc.h" -#include "button.h" -#include "charger.h" -#include "cbi_ec_fw_config.h" -#include "driver/accelgyro_bmi_common.h" -#include "driver/accel_kionix.h" -#include "driver/accel_kx022.h" -#include "driver/retimer/pi3dpx1207.h" -#include "driver/retimer/pi3hdx1204.h" -#include "driver/retimer/ps8811.h" -#include "driver/temp_sensor/sb_tsi.h" -#include "driver/usb_mux/amd_fp5.h" -#include "extpower.h" -#include "fan.h" -#include "fan_chip.h" -#include "gpio.h" -#include "hooks.h" -#include "lid_switch.h" -#include "power.h" -#include "power_button.h" -#include "pwm.h" -#include "pwm_chip.h" -#include "switch.h" -#include "system.h" -#include "task.h" -#include "temp_sensor/thermistor.h" -#include "temp_sensor.h" -#include "usb_charge.h" -#include "usb_mux.h" - -#include "gpio_list.h" - -#define CPRINTSUSB(format, args...) cprints(CC_USBCHARGE, format, ## args) -#define CPRINTFUSB(format, args...) cprintf(CC_USBCHARGE, format, ## args) - -/* Motion sensors */ -static struct mutex g_lid_mutex; -static struct mutex g_base_mutex; - -/* sensor private data */ -static struct kionix_accel_data g_kx022_data; -static struct bmi_drv_data_t g_bmi160_data; - -/* TODO(gcc >= 5.0) Remove the casts to const pointer at rot_standard_ref */ -struct motion_sensor_t motion_sensors[] = { - [LID_ACCEL] = { - .name = "Lid Accel", - .active_mask = SENSOR_ACTIVE_S0_S3, - .chip = MOTIONSENSE_CHIP_KX022, - .type = MOTIONSENSE_TYPE_ACCEL, - .location = MOTIONSENSE_LOC_LID, - .drv = &kionix_accel_drv, - .mutex = &g_lid_mutex, - .drv_data = &g_kx022_data, - .port = I2C_PORT_SENSOR, - .i2c_spi_addr_flags = KX022_ADDR1_FLAGS, - .rot_standard_ref = NULL, - .default_range = 2, /* g, enough for laptop. */ - .min_frequency = KX022_ACCEL_MIN_FREQ, - .max_frequency = KX022_ACCEL_MAX_FREQ, - .config = { - /* EC use accel for angle detection */ - [SENSOR_CONFIG_EC_S0] = { - .odr = 10000 | ROUND_UP_FLAG, - .ec_rate = 100, - }, - /* EC use accel for angle detection */ - [SENSOR_CONFIG_EC_S3] = { - .odr = 10000 | ROUND_UP_FLAG, - }, - }, - }, - - [BASE_ACCEL] = { - .name = "Base Accel", - .active_mask = SENSOR_ACTIVE_S0_S3, - .chip = MOTIONSENSE_CHIP_BMI160, - .type = MOTIONSENSE_TYPE_ACCEL, - .location = MOTIONSENSE_LOC_BASE, - .drv = &bmi160_drv, - .mutex = &g_base_mutex, - .drv_data = &g_bmi160_data, - .port = I2C_PORT_SENSOR, - .i2c_spi_addr_flags = BMI160_ADDR0_FLAGS, - .default_range = 4, /* g, to meet CDD 7.3.1/C-1-4 reqs.*/ - .rot_standard_ref = NULL, - .min_frequency = BMI_ACCEL_MIN_FREQ, - .max_frequency = BMI_ACCEL_MAX_FREQ, - .config = { - /* EC use accel for angle detection */ - [SENSOR_CONFIG_EC_S0] = { - .odr = 10000 | ROUND_UP_FLAG, - .ec_rate = 100, - }, - /* EC use accel for angle detection */ - [SENSOR_CONFIG_EC_S3] = { - .odr = 10000 | ROUND_UP_FLAG, - }, - }, - }, - - [BASE_GYRO] = { - .name = "Base Gyro", - .active_mask = SENSOR_ACTIVE_S0_S3, - .chip = MOTIONSENSE_CHIP_BMI160, - .type = MOTIONSENSE_TYPE_GYRO, - .location = MOTIONSENSE_LOC_BASE, - .drv = &bmi160_drv, - .mutex = &g_base_mutex, - .drv_data = &g_bmi160_data, - .port = I2C_PORT_SENSOR, - .i2c_spi_addr_flags = BMI160_ADDR0_FLAGS, - .default_range = 1000, /* dps */ - .rot_standard_ref = NULL, - .min_frequency = BMI_GYRO_MIN_FREQ, - .max_frequency = BMI_GYRO_MAX_FREQ, - }, -}; - -unsigned int motion_sensor_count = ARRAY_SIZE(motion_sensors); - -const struct power_signal_info power_signal_list[] = { - [X86_SLP_S3_N] = { - .gpio = GPIO_PCH_SLP_S3_L, - .flags = POWER_SIGNAL_ACTIVE_HIGH, - .name = "SLP_S3_DEASSERTED", - }, - [X86_SLP_S5_N] = { - .gpio = GPIO_PCH_SLP_S5_L, - .flags = POWER_SIGNAL_ACTIVE_HIGH, - .name = "SLP_S5_DEASSERTED", - }, - [X86_S0_PGOOD] = { - .gpio = GPIO_S0_PGOOD, - .flags = POWER_SIGNAL_ACTIVE_HIGH, - .name = "S0_PGOOD", - }, - [X86_S5_PGOOD] = { - .gpio = GPIO_S5_PGOOD, - .flags = POWER_SIGNAL_ACTIVE_HIGH, - .name = "S5_PGOOD", - }, -}; -BUILD_ASSERT(ARRAY_SIZE(power_signal_list) == POWER_SIGNAL_COUNT); - -const struct pwm_t pwm_channels[] = { - [PWM_CH_KBLIGHT] = { - .channel = 3, - .flags = PWM_CONFIG_DSLEEP, - .freq = 100, - }, - [PWM_CH_FAN] = { - .channel = 2, - .flags = PWM_CONFIG_OPEN_DRAIN, - .freq = 25000, - }, -}; -BUILD_ASSERT(ARRAY_SIZE(pwm_channels) == PWM_CH_COUNT); - -/* MFT channels. These are logically separate from pwm_channels. */ -const struct mft_t mft_channels[] = { - [MFT_CH_0] = { - .module = NPCX_MFT_MODULE_1, - .clk_src = TCKC_LFCLK, - .pwm_id = PWM_CH_FAN, - }, -}; -BUILD_ASSERT(ARRAY_SIZE(mft_channels) == MFT_CH_COUNT); - -const int usb_port_enable[USBA_PORT_COUNT] = { - IOEX_EN_USB_A0_5V, - IOEX_EN_USB_A1_5V_DB, -}; - -const struct pi3hdx1204_tuning pi3hdx1204_tuning = { - .eq_ch0_ch1_offset = PI3HDX1204_EQ_DB710, - .eq_ch2_ch3_offset = PI3HDX1204_EQ_DB710, - .vod_offset = PI3HDX1204_VOD_130_ALL_CHANNELS, - .de_offset = PI3HDX1204_DE_DB_MINUS5, -}; - -/***************************************************************************** - * Board suspend / resume - */ -#define PS8811_ACCESS_RETRIES 2 - -static void board_chipset_resume(void) -{ - int rv; - int retry; - - /* Turn on the retimers */ - ioex_set_level(IOEX_USB_A0_RETIMER_EN, 1); - ioex_set_level(IOEX_USB_A1_RETIMER_EN, 1); - - /* USB-A0 can run with default settings */ - for (retry = 0; retry < PS8811_ACCESS_RETRIES; ++retry) { - int val; - - rv = i2c_read8(I2C_PORT_USBA0, - PS8811_I2C_ADDR_FLAGS3 + PS8811_REG_PAGE1, - PS8811_REG1_USB_BEQ_LEVEL, &val); - if (!rv) - break; - } - if (rv) { - ioex_set_level(IOEX_USB_A0_RETIMER_EN, 0); - CPRINTSUSB("A0: PS8811 not detected"); - } - - /* USB-A1 needs to increase gain to get over MB/DB connector */ - for (retry = 0; retry < PS8811_ACCESS_RETRIES; ++retry) { - rv = i2c_write8(I2C_PORT_USBA1, - PS8811_I2C_ADDR_FLAGS3 + PS8811_REG_PAGE1, - PS8811_REG1_USB_BEQ_LEVEL, - PS8811_BEQ_I2C_LEVEL_UP_13DB | - PS8811_BEQ_PIN_LEVEL_UP_18DB); - if (!rv) - break; - } - if (rv) { - ioex_set_level(IOEX_USB_A1_RETIMER_EN, 0); - CPRINTSUSB("A1: PS8811 not detected"); - } - - if (ec_config_has_hdmi_retimer_pi3hdx1204()) { - pi3hdx1204_enable(I2C_PORT_TCPC1, - PI3HDX1204_I2C_ADDR_FLAGS, - 1); - } -} -DECLARE_HOOK(HOOK_CHIPSET_RESUME, board_chipset_resume, HOOK_PRIO_DEFAULT); - -static void board_chipset_suspend(void) -{ - ioex_set_level(IOEX_USB_A0_RETIMER_EN, 0); - ioex_set_level(IOEX_USB_A1_RETIMER_EN, 0); - - if (ec_config_has_hdmi_retimer_pi3hdx1204()) { - pi3hdx1204_enable(I2C_PORT_TCPC1, - PI3HDX1204_I2C_ADDR_FLAGS, - 0); - } -} -DECLARE_HOOK(HOOK_CHIPSET_SUSPEND, board_chipset_suspend, HOOK_PRIO_DEFAULT); - -/***************************************************************************** - * USB-C MUX/Retimer dynamic configuration - */ -static void setup_mux(void) -{ - if (ec_config_has_usbc1_retimer_ps8802()) { - /* - * Main MUX is PS8802, secondary MUX is modified FP5 - * - * Replace usb_muxes[USBC_PORT_C1] with the PS8802 - * table entry. - */ - memcpy(&usb_muxes[USBC_PORT_C1], - &usbc1_ps8802, - sizeof(struct usb_mux)); - - /* Set the AMD FP5 as the secondary MUX */ - usb_muxes[USBC_PORT_C1].next_mux = &usbc1_amd_fp5_usb_mux; - - /* Don't have the AMD FP5 flip */ - usbc1_amd_fp5_usb_mux.flags = USB_MUX_FLAG_SET_WITHOUT_FLIP; - - } else if (ec_config_has_usbc1_retimer_ps8818()) { - /* - * Main MUX is FP5, secondary MUX is PS8818 - * - * Replace usb_muxes[USBC_PORT_C1] with the AMD FP5 - * table entry. - */ - memcpy(&usb_muxes[USBC_PORT_C1], - &usbc1_amd_fp5_usb_mux, - sizeof(struct usb_mux)); - - /* Set the PS8818 as the secondary MUX */ - usb_muxes[USBC_PORT_C1].next_mux = &usbc1_ps8818; - } -} - -const struct pi3dpx1207_usb_control pi3dpx1207_controls[] = { - [USBC_PORT_C0] = { - .enable_gpio = IOEX_USB_C0_DATA_EN, - .dp_enable_gpio = GPIO_USB_C0_IN_HPD, - }, - [USBC_PORT_C1] = { - }, -}; -BUILD_ASSERT(ARRAY_SIZE(pi3dpx1207_controls) == USBC_PORT_COUNT); - -const struct usb_mux usbc0_pi3dpx1207_usb_retimer = { - .usb_port = USBC_PORT_C0, - .i2c_port = I2C_PORT_TCPC0, - .i2c_addr_flags = PI3DPX1207_I2C_ADDR_FLAGS, - .driver = &pi3dpx1207_usb_retimer, -}; - -struct usb_mux usb_muxes[] = { - [USBC_PORT_C0] = { - .usb_port = USBC_PORT_C0, - .i2c_port = I2C_PORT_USB_AP_MUX, - .i2c_addr_flags = AMD_FP5_MUX_I2C_ADDR_FLAGS, - .driver = &amd_fp5_usb_mux_driver, - .next_mux = &usbc0_pi3dpx1207_usb_retimer, - }, - [USBC_PORT_C1] = { - /* Filled in dynamically at startup */ - }, -}; -BUILD_ASSERT(ARRAY_SIZE(usb_muxes) == USBC_PORT_COUNT); - -/***************************************************************************** - * Use FW_CONFIG to set correct configuration. - */ - -int board_usbc1_retimer_inhpd = IOEX_USB_C1_HPD_IN_DB; - -static void setup_v0_charger(void) -{ - chg_chips[0].i2c_port = I2C_PORT_CHARGER_V0; -} -/* - * Use HOOK_PRIO_INIT_I2C so we re-map before charger_chips_init() - * talks to the charger. - */ -DECLARE_HOOK(HOOK_INIT, setup_v0_charger, HOOK_PRIO_INIT_I2C); - -static void setup_fw_config(void) -{ - /* Enable Gyro interrupts */ - gpio_enable_interrupt(GPIO_6AXIS_INT_L); - - setup_mux(); - - if (ec_config_has_mst_hub_rtd2141b()) - ioex_enable_interrupt(IOEX_MST_HPD_OUT); - - if (ec_config_has_hdmi_conn_hpd()) - ioex_enable_interrupt(IOEX_HDMI_CONN_HPD_3V3_DB); -} -/* Use HOOK_PRIO_INIT_I2C + 2 to be after ioex_init(). */ -DECLARE_HOOK(HOOK_INIT, setup_fw_config, HOOK_PRIO_INIT_I2C + 2); - -/***************************************************************************** - * Fan - */ - -/* Physical fans. These are logically separate from pwm_channels. */ -const struct fan_conf fan_conf_0 = { - .flags = FAN_USE_RPM_MODE, - .ch = MFT_CH_0, /* Use MFT id to control fan */ - .pgood_gpio = -1, - .enable_gpio = -1, -}; -const struct fan_rpm fan_rpm_0 = { - .rpm_min = 3000, - .rpm_start = 3000, - .rpm_max = 4900, -}; -const struct fan_t fans[] = { - [FAN_CH_0] = { - .conf = &fan_conf_0, - .rpm = &fan_rpm_0, - }, -}; -BUILD_ASSERT(ARRAY_SIZE(fans) == FAN_CH_COUNT); - -int board_get_temp(int idx, int *temp_k) -{ - int mv; - int temp_c; - enum adc_channel channel; - - /* idx is the sensor index set in board temp_sensors[] */ - switch (idx) { - case TEMP_SENSOR_CHARGER: - channel = ADC_TEMP_SENSOR_CHARGER; - break; - case TEMP_SENSOR_SOC: - /* thermistor is not powered in G3 */ - if (chipset_in_state(CHIPSET_STATE_HARD_OFF)) - return EC_ERROR_NOT_POWERED; - - channel = ADC_TEMP_SENSOR_SOC; - break; - default: - return EC_ERROR_INVAL; - } - - mv = adc_read_channel(channel); - if (mv < 0) - return EC_ERROR_INVAL; - - temp_c = thermistor_linear_interpolate(mv, &thermistor_info); - *temp_k = C_TO_K(temp_c); - return EC_SUCCESS; -} - -const struct adc_t adc_channels[] = { - [ADC_TEMP_SENSOR_CHARGER] = { - .name = "CHARGER", - .input_ch = NPCX_ADC_CH2, - .factor_mul = ADC_MAX_VOLT, - .factor_div = ADC_READ_MAX + 1, - .shift = 0, - }, - [ADC_TEMP_SENSOR_SOC] = { - .name = "SOC", - .input_ch = NPCX_ADC_CH3, - .factor_mul = ADC_MAX_VOLT, - .factor_div = ADC_READ_MAX + 1, - .shift = 0, - }, -}; -BUILD_ASSERT(ARRAY_SIZE(adc_channels) == ADC_CH_COUNT); - -const struct temp_sensor_t temp_sensors[] = { - [TEMP_SENSOR_CHARGER] = { - .name = "Charger", - .type = TEMP_SENSOR_TYPE_BOARD, - .read = board_get_temp, - .idx = TEMP_SENSOR_CHARGER, - }, - [TEMP_SENSOR_SOC] = { - .name = "SOC", - .type = TEMP_SENSOR_TYPE_BOARD, - .read = board_get_temp, - .idx = TEMP_SENSOR_SOC, - }, - [TEMP_SENSOR_CPU] = { - .name = "CPU", - .type = TEMP_SENSOR_TYPE_CPU, - .read = sb_tsi_get_val, - .idx = 0, - }, -}; -BUILD_ASSERT(ARRAY_SIZE(temp_sensors) == TEMP_SENSOR_COUNT); - -const static struct ec_thermal_config thermal_thermistor = { - .temp_host = { - [EC_TEMP_THRESH_HIGH] = C_TO_K(90), - [EC_TEMP_THRESH_HALT] = C_TO_K(92), - }, - .temp_host_release = { - [EC_TEMP_THRESH_HIGH] = C_TO_K(80), - }, - .temp_fan_off = C_TO_K(25), - .temp_fan_max = C_TO_K(58), -}; - -const static struct ec_thermal_config thermal_cpu = { - .temp_host = { - [EC_TEMP_THRESH_HIGH] = C_TO_K(90), - [EC_TEMP_THRESH_HALT] = C_TO_K(92), - }, - .temp_host_release = { - [EC_TEMP_THRESH_HIGH] = C_TO_K(80), - }, - .temp_fan_off = C_TO_K(25), - .temp_fan_max = C_TO_K(58), -}; - -struct ec_thermal_config thermal_params[TEMP_SENSOR_COUNT]; - -static void setup_fans(void) -{ - thermal_params[TEMP_SENSOR_CHARGER] = thermal_thermistor; - thermal_params[TEMP_SENSOR_SOC] = thermal_thermistor; - thermal_params[TEMP_SENSOR_CPU] = thermal_cpu; -} -DECLARE_HOOK(HOOK_INIT, setup_fans, HOOK_PRIO_DEFAULT); - -/***************************************************************************** - * MST hub - */ - -static void mst_hpd_handler(void) -{ - int hpd = 0; - - /* - * Ensure level on GPIO_DP1_HPD matches IOEX_MST_HPD_OUT, in case - * we got out of sync. - */ - ioex_get_level(IOEX_MST_HPD_OUT, &hpd); - gpio_set_level(GPIO_DP1_HPD, hpd); - ccprints("MST HPD %d", hpd); -} -DECLARE_DEFERRED(mst_hpd_handler); - -void mst_hpd_interrupt(enum ioex_signal signal) -{ - /* - * Goal is to pass HPD through from DB OPT3 MST hub to AP's DP1. - * Immediately invert GPIO_DP1_HPD, to pass through the edge on - * IOEX_MST_HPD_OUT. Then check level after 2 msec debounce. - */ - int hpd = !gpio_get_level(GPIO_DP1_HPD); - - gpio_set_level(GPIO_DP1_HPD, hpd); - hook_call_deferred(&mst_hpd_handler_data, (2 * MSEC)); -} - -static void hdmi_hpd_handler(void) -{ - int hpd = 0; - - /* Pass HPD through from DB OPT1 HDMI connector to AP's DP1. */ - ioex_get_level(IOEX_HDMI_CONN_HPD_3V3_DB, &hpd); - gpio_set_level(GPIO_DP1_HPD, hpd); - ccprints("HDMI HPD %d", hpd); -} -DECLARE_DEFERRED(hdmi_hpd_handler); - -void hdmi_hpd_interrupt(enum ioex_signal signal) -{ - /* Debounce for 2 msec. */ - hook_call_deferred(&hdmi_hpd_handler_data, (2 * MSEC)); -} diff --git a/board/trembyle/board.h b/board/trembyle/board.h deleted file mode 100644 index bfbd829ac1..0000000000 --- a/board/trembyle/board.h +++ /dev/null @@ -1,218 +0,0 @@ -/* Copyright 2019 The Chromium OS Authors. All rights reserved. - * Use of this source code is governed by a BSD-style license that can be - * found in the LICENSE file. - */ - -/* Trembyle board configuration */ - -#ifndef __CROS_EC_BOARD_H -#define __CROS_EC_BOARD_H - -#define VARIANT_ZORK_TREMBYLE - -#include <stdbool.h> -#include "baseboard.h" - -#define CONFIG_USBC_RETIMER_PI3DPX1207 - -/* Motion sensing drivers */ -#define CONFIG_ACCELGYRO_BMI160 -#define CONFIG_ACCELGYRO_BMI160_INT_EVENT \ - TASK_EVENT_MOTION_SENSOR_INTERRUPT(BASE_ACCEL) -#define CONFIG_ACCEL_INTERRUPTS -#define CONFIG_ACCEL_KX022 -#define CONFIG_CMD_ACCELS -#define CONFIG_CMD_ACCEL_INFO -#define CONFIG_TABLET_MODE -#define CONFIG_LID_ANGLE -#define CONFIG_LID_ANGLE_UPDATE -#define CONFIG_LID_ANGLE_SENSOR_BASE BASE_ACCEL -#define CONFIG_LID_ANGLE_SENSOR_LID LID_ACCEL - -/* GPIO mapping from board specific name to EC common name. */ -#define CONFIG_BATTERY_PRESENT_GPIO GPIO_EC_BATT_PRES_ODL -#define CONFIG_SCI_GPIO GPIO_EC_FCH_SCI_ODL -#define GPIO_AC_PRESENT GPIO_ACOK_OD -#define GPIO_CPU_PROCHOT GPIO_PROCHOT_ODL -#define GPIO_EC_INT_L GPIO_EC_AP_INT_ODL -#define GPIO_ENABLE_BACKLIGHT_L GPIO_EC_EDP_BL_DISABLE -#define GPIO_ENTERING_RW GPIO_EC_ENTERING_RW -#define GPIO_KBD_KSO2 GPIO_EC_KSO_02_INV -#define GPIO_PCH_PWRBTN_L GPIO_EC_FCH_PWR_BTN_L -#define GPIO_PCH_RSMRST_L GPIO_EC_FCH_RSMRST_L -#define GPIO_PCH_SLP_S3_L GPIO_SLP_S3_L -#define GPIO_PCH_SLP_S5_L GPIO_SLP_S5_L -#define GPIO_PCH_SYS_PWROK GPIO_EC_FCH_PWROK -#define GPIO_PCH_WAKE_L GPIO_EC_FCH_WAKE_L -#define GPIO_POWER_BUTTON_L GPIO_EC_PWR_BTN_ODL -#define GPIO_S0_PGOOD GPIO_S0_PWROK_OD -#define GPIO_S5_PGOOD GPIO_EC_PWROK_OD -#define GPIO_SYS_RESET_L GPIO_EC_SYS_RST_L -#define GPIO_VOLUME_DOWN_L GPIO_VOLDN_BTN_ODL -#define GPIO_VOLUME_UP_L GPIO_VOLUP_BTN_ODL -#define GPIO_WP_L GPIO_EC_WP_L -#define GPIO_PACKET_MODE_EN GPIO_EC_H1_PACKET_MODE - -#ifndef __ASSEMBLER__ - -enum adc_channel { - ADC_TEMP_SENSOR_CHARGER, - ADC_TEMP_SENSOR_SOC, - ADC_CH_COUNT -}; - -enum battery_type { - BATTERY_AP18F4M, - BATTERY_TYPE_COUNT, -}; - -enum mft_channel { - MFT_CH_0 = 0, - /* Number of MFT channels */ - MFT_CH_COUNT, -}; - -enum pwm_channel { - PWM_CH_KBLIGHT = 0, - PWM_CH_FAN, - PWM_CH_COUNT -}; - -enum temp_sensor_id { - TEMP_SENSOR_CHARGER = 0, - TEMP_SENSOR_SOC, - TEMP_SENSOR_CPU, - TEMP_SENSOR_COUNT -}; - -enum usba_port { - USBA_PORT_A0 = 0, - USBA_PORT_A1, - USBA_PORT_COUNT -}; - -/***************************************************************************** - * CBI EC FW Configuration - */ - -/** - * TREMBYLE_MB_USBAC - * USB-A0 Speed: 10 Gbps - * Retimer: PS8811 - * USB-C0 Speed: 10 Gbps - * Retimer: PI3DPX1207 - * TCPC: NCT3807 - * PPC: AOZ1380 - * IOEX: TCPC - */ -enum ec_cfg_usb_mb_type { - TREMBYLE_MB_USBAC = 0, -}; - -/** - * TREMBYLE_DB_T_OPT1_USBAC_HMDI - * USB-A1 Speed: 10 Gbps - * Retimer: PS8811 - * USB-C1 Speed: 10 Gbps - * Retimer: PS8818 - * TCPC: NCT3807 - * PPC: NX20P3483 - * IOEX: TCPC - * HDMI Exists: yes - * Retimer: PI3HDX1204 - * MST Hub: none - * - * TREMBYLE_DB_T_OPT2_USBAC - * USB-A1 Speed: 10 Gbps - * Retimer: PS8811 - * USB-C1 Speed: 10 Gbps - * Retimer: PS8802 - * TCPC: NCT3807 - * PPC: NX20P3483 - * IOEX: TCPC - * HDMI Exists: no - * Retimer: none - * MST Hub: none - * - * TREMBYLE_DB_T_OPT3_USBAC_HDMI_MSTHUB - * USB-A1 Speed: 10 Gbps - * Retimer: PS8811 - * USB-C1 Speed: 10 Gbps - * Retimer: PS8802 - * TCPC: NCT3807 - * PPC: NX20P3483 - * IOEX: TCPC - * HDMI Exists: yes - * Retimer: none - * MST Hub: RTD2141B - */ -enum ec_cfg_usb_db_type { - TREMBYLE_DB_T_OPT1_USBAC_HMDI = 0, - TREMBYLE_DB_T_OPT2_USBAC = 1, - TREMBYLE_DB_T_OPT3_USBAC_HDMI_MSTHUB = 2, -}; - -#include "cbi_ec_fw_config.h" - -#define HAS_USBC1_RETIMER_PS8802 \ - (BIT(TREMBYLE_DB_T_OPT2_USBAC) | \ - BIT(TREMBYLE_DB_T_OPT3_USBAC_HDMI_MSTHUB)) - -static inline bool ec_config_has_usbc1_retimer_ps8802(void) -{ - return !!(BIT(ec_config_get_usb_db()) & - HAS_USBC1_RETIMER_PS8802); -} - -#define HAS_USBC1_RETIMER_PS8818 \ - (BIT(TREMBYLE_DB_T_OPT1_USBAC_HMDI)) - -static inline bool ec_config_has_usbc1_retimer_ps8818(void) -{ - return !!(BIT(ec_config_get_usb_db()) & - HAS_USBC1_RETIMER_PS8818); -} - -#define HAS_HDMI_RETIMER_PI3HDX1204 \ - (BIT(TREMBYLE_DB_T_OPT1_USBAC_HMDI)) - -static inline bool ec_config_has_hdmi_retimer_pi3hdx1204(void) -{ - return !!(BIT(ec_config_get_usb_db()) & - HAS_HDMI_RETIMER_PI3HDX1204); -} - -#define HAS_MST_HUB_RTD2141B \ - (BIT(TREMBYLE_DB_T_OPT3_USBAC_HDMI_MSTHUB)) - -static inline bool ec_config_has_mst_hub_rtd2141b(void) -{ - return !!(BIT(ec_config_get_usb_db()) & - HAS_MST_HUB_RTD2141B); -} - -#define HAS_HDMI_CONN_HPD \ - (BIT(TREMBYLE_DB_T_OPT1_USBAC_HMDI)) - -static inline bool ec_config_has_hdmi_conn_hpd(void) -{ - return !!(BIT(ec_config_get_usb_db()) & - HAS_HDMI_CONN_HPD); -} - -#define PORT_TO_HPD(port) ((port == 0) \ - ? GPIO_USB_C0_HPD \ - : (ec_config_has_usbc1_retimer_ps8802()) \ - ? GPIO_DP1_HPD \ - : GPIO_DP2_HPD) - -extern const struct usb_mux usbc0_pi3dpx1207_usb_retimer; -extern const struct usb_mux usbc1_ps8802; -extern const struct usb_mux usbc1_ps8818; -extern struct usb_mux usbc1_amd_fp5_usb_mux; - -void hdmi_hpd_interrupt(enum ioex_signal signal); - -#endif /* !__ASSEMBLER__ */ - -#endif /* __CROS_EC_BOARD_H */ diff --git a/board/trembyle/build.mk b/board/trembyle/build.mk deleted file mode 100644 index 4ca0cbd96f..0000000000 --- a/board/trembyle/build.mk +++ /dev/null @@ -1,15 +0,0 @@ -# -*- makefile -*- -# Copyright 2019 The Chromium OS Authors. All rights reserved. -# Use of this source code is governed by a BSD-style license that can be -# found in the LICENSE file. -# -# Board specific files build -# - -CHIP:=npcx -CHIP_FAMILY:=npcx7 -CHIP_VARIANT:=npcx7m7wc -BASEBOARD:=zork - -board-y=board.o led.o -board-$(CONFIG_BATTERY_SMART)+=battery.o diff --git a/board/trembyle/ec.tasklist b/board/trembyle/ec.tasklist deleted file mode 100644 index 41b83cf4f3..0000000000 --- a/board/trembyle/ec.tasklist +++ /dev/null @@ -1,26 +0,0 @@ -/* Copyright 2019 The Chromium OS Authors. All rights reserved. - * Use of this source code is governed by a BSD-style license that can be - * found in the LICENSE file. - */ - -/* - * See CONFIG_TASK_LIST in config.h for details. - */ - -#define CONFIG_TASK_LIST \ - TASK_ALWAYS(HOOKS, hook_task, NULL, LARGER_TASK_STACK_SIZE) \ - TASK_ALWAYS(CHG_RAMP, chg_ramp_task, NULL, TASK_STACK_SIZE) \ - TASK_ALWAYS(USB_CHG_P0, usb_charger_task, 0, TASK_STACK_SIZE) \ - TASK_ALWAYS(USB_CHG_P1, usb_charger_task, 1, TASK_STACK_SIZE) \ - TASK_ALWAYS(CHARGER, charger_task, NULL, VENTI_TASK_STACK_SIZE) \ - TASK_ALWAYS(MOTIONSENSE, motion_sense_task, NULL, VENTI_TASK_STACK_SIZE) \ - TASK_NOTEST(CHIPSET, chipset_task, NULL, VENTI_TASK_STACK_SIZE) \ - TASK_NOTEST(KEYPROTO, keyboard_protocol_task, NULL, TASK_STACK_SIZE) \ - TASK_ALWAYS(HOSTCMD, host_command_task, NULL, LARGER_TASK_STACK_SIZE) \ - TASK_ALWAYS(CONSOLE, console_task, NULL, VENTI_TASK_STACK_SIZE) \ - TASK_ALWAYS(POWERBTN, power_button_task, NULL, VENTI_TASK_STACK_SIZE) \ - TASK_NOTEST(KEYSCAN, keyboard_scan_task, NULL, TASK_STACK_SIZE) \ - TASK_ALWAYS(PD_C0, pd_task, NULL, VENTI_TASK_STACK_SIZE) \ - TASK_ALWAYS(PD_C1, pd_task, NULL, VENTI_TASK_STACK_SIZE) \ - TASK_ALWAYS(PD_INT_C0, pd_interrupt_handler_task, 0, TASK_STACK_SIZE) \ - TASK_ALWAYS(PD_INT_C1, pd_interrupt_handler_task, 1, TASK_STACK_SIZE) diff --git a/board/trembyle/gpio.inc b/board/trembyle/gpio.inc deleted file mode 100644 index 6cc3e6fe09..0000000000 --- a/board/trembyle/gpio.inc +++ /dev/null @@ -1,141 +0,0 @@ -/* -*- mode:c -*- - * - * Copyright 2019 The Chromium OS Authors. All rights reserved. - * Use of this source code is governed by a BSD-style license that can be - * found in the LICENSE file. - */ - -/* Declare symbolic names for all the GPIOs that we care about. - * Note: Those with interrupt handlers must be declared first. */ - -GPIO_INT(USB_C0_TCPC_INT_ODL, PIN(3, 4), GPIO_INT_FALLING, tcpc_alert_event) -GPIO_INT(USB_C1_TCPC_INT_ODL, PIN(F, 1), GPIO_INT_FALLING, tcpc_alert_event) -GPIO_INT(USB_C0_PPC_FAULT_ODL, PIN(6, 3), GPIO_INT_FALLING, ppc_interrupt) -GPIO_INT(USB_C1_PPC_INT_ODL, PIN(D, 4), GPIO_INT_FALLING, ppc_interrupt) -GPIO_INT(USB_C0_BC12_INT_ODL, PIN(9, 3), GPIO_INT_FALLING | GPIO_PULL_UP, bc12_interrupt) -GPIO_INT(USB_C1_BC12_INT_ODL, PIN(A, 4), GPIO_INT_FALLING | GPIO_PULL_UP, bc12_interrupt) -GPIO_INT(SLP_S3_L, PIN(7, 4), GPIO_INT_BOTH, power_signal_interrupt) -GPIO_INT(SLP_S5_L, PIN(E, 0), GPIO_INT_BOTH, power_signal_interrupt) -GPIO_INT(S0_PWROK_OD, PIN(5, 6), GPIO_INT_BOTH, power_signal_interrupt) -GPIO_INT(EC_PWROK_OD, PIN(3, 7), GPIO_INT_BOTH, power_signal_interrupt) -GPIO_INT(EC_PWR_BTN_ODL, PIN(0, 1), GPIO_INT_BOTH, power_button_interrupt) -GPIO_INT(LID_OPEN, PIN(D, 2), GPIO_INT_BOTH | GPIO_HIB_WAKE_HIGH, lid_interrupt) -GPIO_INT(ACOK_OD, PIN(0, 0), GPIO_INT_BOTH | GPIO_HIB_WAKE_HIGH, extpower_interrupt) -GPIO_INT(EC_WP_L, PIN(5, 0), GPIO_INT_BOTH, switch_interrupt) -GPIO_INT(VOLDN_BTN_ODL, PIN(A, 6), GPIO_INT_BOTH | GPIO_PULL_UP, button_interrupt) -GPIO_INT(VOLUP_BTN_ODL, PIN(9, 5), GPIO_INT_BOTH | GPIO_PULL_UP, button_interrupt) -GPIO_INT(6AXIS_INT_L, PIN(A, 0), GPIO_INT_FALLING | GPIO_PULL_UP, bmi160_interrupt) - -/* GPIO_INT_BOTH is required for PSL wake from hibernate, but we don't need an interrupt handler. */ -GPIO(EC_RST_ODL, PIN(0, 2), GPIO_INT_BOTH | GPIO_HIB_WAKE_HIGH) - -GPIO(3AXIS_INT_L, PIN(9, 6), GPIO_INPUT | GPIO_PULL_DOWN) /* 3 Axis Accel */ -GPIO(CCD_MODE_ODL, PIN(C, 6), GPIO_INPUT) /* Case Closed Debug Mode */ -GPIO(PROCHOT_ODL, PIN(D, 5), GPIO_ODR_HIGH) /* PROCHOT to SOC */ -GPIO(EC_BATT_PRES_ODL, PIN(4, 1), GPIO_INPUT) /* Battery Present */ -GPIO(EC_AP_INT_ODL, PIN(A, 3), GPIO_ODR_HIGH) /* Sensor MKBP event to SOC */ -GPIO(EN_PWR_A, PIN(B, 7), GPIO_OUT_LOW) /* Enable Power */ -GPIO(EC_EDP_BL_DISABLE, PIN(A, 2), GPIO_OUT_HIGH) /* Enable Backlight */ -GPIO(EC_ENTERING_RW, PIN(E, 5), GPIO_OUT_LOW) /* EC Entering RW */ -GPIO(EC_FCH_PWR_BTN_L, PIN(6, 2), GPIO_OUT_HIGH) /* Power Button to SOC */ -GPIO(EC_FCH_RSMRST_L, PIN(A, 1), GPIO_OUT_LOW) /* RSMRST# to SOC */ -GPIO(EC_FCH_PWROK, PIN(D, 3), GPIO_OUT_LOW) /* Power OK to SOC */ -GPIO(EC_FCH_WAKE_L, PIN(0, 3), GPIO_OUT_HIGH) /* Wake SOC */ -GPIO(EC_FCH_SCI_ODL, PIN(7, 6), GPIO_ODR_HIGH) /* SCI to SOC */ -GPIO(EC_SYS_RST_L, PIN(C, 7), GPIO_ODR_HIGH) /* Cold Reset to SOC */ -GPIO(USB_C0_TCPC_RST_L, PIN(E, 1), GPIO_OUT_HIGH) /* C0 TCPC Reset */ -GPIO(USB_C1_TCPC_RST_L, PIN(F, 0), GPIO_OUT_HIGH) /* C1 TCPC Reset */ -GPIO(USB_C0_HPD, PIN(F, 5), GPIO_OUT_LOW) /* C0 DP Hotplug Detect */ -GPIO(USB_C0_IN_HPD, PIN(7, 3), GPIO_OUT_LOW) /* C0 IN Hotplug Detect */ -GPIO(DP1_HPD, PIN(F, 4), GPIO_OUT_LOW) /* C1 DP Hotplug Detect */ -GPIO(DP2_HPD, PIN(C, 1), GPIO_OUT_LOW) /* C1 DP Hotplug Detect */ -GPIO(EC_H1_PACKET_MODE, PIN(8, 6), GPIO_OUT_LOW) /* H1 Packet Mode */ -GPIO(EN_PWR_TOUCHPAD_PS2, PIN(C, 2), GPIO_INPUT) /* Touchpad Power */ - -UNIMPLEMENTED(PCH_SMI_L) - -GPIO(LED_FULL_L, PIN(6, 0), GPIO_OUT_HIGH) -GPIO(LED_CHRG_L, PIN(C, 0), GPIO_OUT_HIGH) - -IOEX_INT(USB_C0_SBU_FAULT_ODL, EXPIN(USBC_PORT_C0, 1, 2), GPIO_INT_FALLING, sbu_fault_interrupt) -IOEX_INT(USB_C1_SBU_FAULT_DB_ODL, EXPIN(USBC_PORT_C1, 1, 2), GPIO_INT_FALLING, sbu_fault_interrupt) -IOEX_INT(HDMI_CONN_HPD_3V3_DB, EXPIN(USBC_PORT_C1, 1, 0), GPIO_INT_BOTH, hdmi_hpd_interrupt) -IOEX_INT(MST_HPD_OUT, EXPIN(USBC_PORT_C1, 0, 3), GPIO_INT_BOTH, mst_hpd_interrupt) - -IOEX(USB_A0_RETIMER_EN, EXPIN(USBC_PORT_C0, 0, 0), GPIO_OUT_LOW) /* A0 Retimer Enable */ -IOEX(USB_A0_RETIMER_RST, EXPIN(USBC_PORT_C0, 0, 1), GPIO_OUT_LOW) /* A0 Retimer Reset */ -IOEX(USB_C0_FAULT_ODL, EXPIN(USBC_PORT_C0, 0, 3), GPIO_ODR_HIGH) /* C0 Fault to SOC */ -IOEX(USB_C0_TCPC_FASTSW_CTL_EN, EXPIN(USBC_PORT_C0, 0, 4), GPIO_OUT_LOW) /* C0 FastSwitch Control */ -IOEX(USB_C1_FAULT_ODL, EXPIN(USBC_PORT_C0, 1, 0), GPIO_ODR_HIGH) /* C1 Fault to SOC */ -IOEX(USB_C0_PPC_ILIM_3A_EN, EXPIN(USBC_PORT_C0, 1, 1), GPIO_OUT_LOW) /* C0 3A Current Limit Enable */ -IOEX(KB_BL_EN, EXPIN(USBC_PORT_C0, 1, 3), GPIO_OUT_LOW) /* KB Backlight Enable */ -IOEX(USB_C0_DATA_EN, EXPIN(USBC_PORT_C0, 1, 4), GPIO_OUT_LOW) /* C0 Data Enable */ -IOEX(EN_USB_A0_5V, EXPIN(USBC_PORT_C0, 1, 5), GPIO_OUT_LOW) /* A0 5V Source Enable */ -IOEX(USB_A0_CHARGE_EN_L, EXPIN(USBC_PORT_C0, 1, 6), GPIO_OUT_HIGH) /* A0 5V High Current Enable */ - -IOEX(USB_A1_RETIMER_EN, EXPIN(USBC_PORT_C1, 0, 0), GPIO_OUT_LOW) /* A1 Retimer Enable */ -IOEX(USB_A1_RETIMER_RST_DB, EXPIN(USBC_PORT_C1, 0, 1), GPIO_OUT_LOW) /* A1 Retimer Reset */ -IOEX(USB_C1_HPD_IN_DB, EXPIN(USBC_PORT_C1, 0, 2), GPIO_OUT_LOW) /* C1 HPD */ -IOEX(USB_C1_TCPC_FASTSW_CTL_EN, EXPIN(USBC_PORT_C1, 0, 4), GPIO_OUT_LOW) /* C1 FastSwitch Control */ -IOEX(USB_C1_MUX_RST_DB, EXPIN(USBC_PORT_C1, 1, 1), GPIO_OUT_LOW) /* C1 Mux Reset */ -IOEX(USB_C1_PPC_EN_L, EXPIN(USBC_PORT_C1, 1, 3), GPIO_OUT_LOW) /* C1 PPC Enable */ -IOEX(HDMI_DATA_EN_DB, EXPIN(USBC_PORT_C1, 1, 4), GPIO_OUT_HIGH) /* HDMI Retimer Enable */ -IOEX(USB_C1_DATA_EN, EXPIN(USBC_PORT_C1, 1, 5), GPIO_OUT_HIGH) /* C1 Retimer Enable */ -IOEX(EN_USB_A1_5V_DB, EXPIN(USBC_PORT_C1, 1, 6), GPIO_OUT_LOW) /* A1 5V Source Enable */ -IOEX(USB_A1_CHARGE_EN_DB_L, EXPIN(USBC_PORT_C1, 1, 7), GPIO_OUT_HIGH) /* A1 5V High Current Enable */ - -/* - * The NPCX LPC driver configures and controls SCI, so PCH_SCI_ODL [PIN(7, 6)] - * is not defined here as GPIO. - */ - -/* I2C pins - these will be reconfigured for alternate function below */ -GPIO(EC_I2C_USB_A0_C0_SCL, PIN(B, 5), GPIO_INPUT) -GPIO(EC_I2C_USB_A0_C0_SDA, PIN(B, 4), GPIO_INPUT) -GPIO(EC_I2C_USB_A1_C1_SCL, PIN(9, 0), GPIO_INPUT) -GPIO(EC_I2C_USB_A1_C1_SDA, PIN(8, 7), GPIO_INPUT) -GPIO(EC_I2C_BATT_SCL, PIN(9, 2), GPIO_INPUT) -GPIO(EC_I2C_BATT_SDA, PIN(9, 1), GPIO_INPUT) -GPIO(EC_I2C_USBC_AP_MUX_SCL, PIN(D, 1), GPIO_INPUT) -GPIO(EC_I2C_USBC_AP_MUX_SDA, PIN(D, 0), GPIO_INPUT) -GPIO(FCH_SIC_POWER_SCL, PIN(F, 3), GPIO_INPUT) -GPIO(FCH_SID_POWER_SDA, PIN(F, 2), GPIO_INPUT) -GPIO(EC_I2C_SENSOR_CBI_SCL, PIN(3, 3), GPIO_INPUT) -GPIO(EC_I2C_SENSOR_CBI_SDA, PIN(3, 6), GPIO_INPUT) -GPIO(FCH_I2C_AUDIO_SCL, PIN(E, 4), GPIO_INPUT | GPIO_SEL_1P8V) -GPIO(FCH_I2C_AUDIO_SDA, PIN(E, 3), GPIO_INPUT | GPIO_SEL_1P8V) -GPIO(FCH_I2C_HDMI_HUB_3V3_SCL, PIN(B, 3), GPIO_INPUT) -GPIO(FCH_I2C_HDMI_HUB_3V3_SDA, PIN(B, 2), GPIO_INPUT) - -ALTERNATE(PIN_MASK(6, BIT(4) | BIT(5)), 0, MODULE_UART, 0) /* Cr50 requires no pullups. */ - -ALTERNATE(PIN_MASK(B, BIT(4) | BIT(5)), 0, MODULE_I2C, 0) /* I2C0 */ -ALTERNATE(PIN_MASK(9, BIT(0) | BIT(1) | BIT(2)), 0, MODULE_I2C, 0) /* I2C1 SCL / I2C2 */ -ALTERNATE(PIN_MASK(8, BIT(7)), 0, MODULE_I2C, 0) /* I2C1 SDA */ -ALTERNATE(PIN_MASK(D, BIT(0) | BIT(1)), 0, MODULE_I2C, 0) /* I2C3 */ -ALTERNATE(PIN_MASK(F, BIT(2) | BIT(3)), 0, MODULE_I2C, 0) /* I2C4 */ -ALTERNATE(PIN_MASK(3, BIT(3) | BIT(6)), 0, MODULE_I2C, 0) /* I2C5 */ -ALTERNATE(PIN_MASK(E, BIT(3) | BIT(4)), 0, MODULE_I2C, 0) /* I2C6 */ -ALTERNATE(PIN_MASK(B, BIT(2) | BIT(3)), 0, MODULE_I2C, 0) /* I2C7 */ - -ALTERNATE(PIN_MASK(4, BIT(2) | BIT(3)), 0, MODULE_ADC, 0) /* ADC2, ADC3 Temp Sensors */ - -ALTERNATE(PIN_MASK(C, BIT(3)), 0, MODULE_PWM, 0) /* PWM0 LED */ -ALTERNATE(PIN_MASK(C, BIT(4)), 0, MODULE_PWM, 0) /* PWM2 - EC_FAN_PWM */ -ALTERNATE(PIN_MASK(8, BIT(0)), 0, MODULE_PWM, 0) /* PWM3 KB Backlight */ -ALTERNATE(PIN_MASK(4, BIT(0)), 0, MODULE_PWM, 0) /* TA1 - EC_FAN_SPEED */ - -ALTERNATE(PIN_MASK(3, 0x03), 0, MODULE_KEYBOARD_SCAN, GPIO_INPUT) /* KSI_00-01 */ -ALTERNATE(PIN_MASK(2, 0xFC), 0, MODULE_KEYBOARD_SCAN, GPIO_INPUT) /* KSI_02-07 */ -ALTERNATE(PIN_MASK(2, 0x03), 0, MODULE_KEYBOARD_SCAN, GPIO_ODR_HIGH) /* KSO_00-01 */ -GPIO(EC_KSO_02_INV, PIN(1, 7), GPIO_OUT_LOW) /* KSO_02 inverted */ -ALTERNATE(PIN_MASK(1, 0x7F), 0, MODULE_KEYBOARD_SCAN, GPIO_ODR_HIGH) /* KSO_03-09 */ -ALTERNATE(PIN_MASK(0, 0xE0), 0, MODULE_KEYBOARD_SCAN, GPIO_ODR_HIGH) /* KSO_10-12 */ - -/* Power Switch Logic (PSL) inputs */ -ALTERNATE(PIN_MASK(0, BIT(0) | BIT(1) | BIT(2)), 0, MODULE_PMU, 0) /* AC_PRESENT, POWER_BUTTON_L, EC_RST_ODL */ -ALTERNATE(PIN_MASK(D, BIT(2)), 0, MODULE_PMU, 0) /* LID_OPEN */ - -ALTERNATE(PIN_MASK(A, 0xA0), 1, MODULE_WOV, 0) /* I2S_SYNC/I2S_SCLK GPIOA5/A7 */ -ALTERNATE(PIN_MASK(B, 0x01), 1, MODULE_WOV, 0) /* I2S_SDAT GPIOB0 */ -ALTERNATE(PIN_MASK(9, 0x90), 1, MODULE_WOV, 0) /* DMIC_CLK/DMIC_IN GPIO94/97 */ diff --git a/board/trembyle/led.c b/board/trembyle/led.c deleted file mode 100644 index 3e2d195a06..0000000000 --- a/board/trembyle/led.c +++ /dev/null @@ -1,71 +0,0 @@ -/* Copyright 2019 The Chromium OS Authors. All rights reserved. - * Use of this source code is governed by a BSD-style license that can be - * found in the LICENSE file. - */ - -#include "ec_commands.h" -#include "gpio.h" -#include "led_common.h" -#include "led_onoff_states.h" - -#define LED_OFF_LVL 1 -#define LED_ON_LVL 0 - -__override const int led_charge_lvl_1; -__override const int led_charge_lvl_2 = 100; - -__override struct led_descriptor - led_bat_state_table[LED_NUM_STATES][LED_NUM_PHASES] = { - [STATE_CHARGING_LVL_1] = {{EC_LED_COLOR_BLUE, 2 * LED_ONE_SEC}, - {EC_LED_COLOR_RED, 2 * LED_ONE_SEC} }, - [STATE_CHARGING_LVL_2] = {{EC_LED_COLOR_RED, LED_INDEFINITE} }, - [STATE_CHARGING_FULL_CHARGE] = {{EC_LED_COLOR_BLUE, LED_INDEFINITE} }, - [STATE_DISCHARGE_S0] = {{EC_LED_COLOR_BLUE, LED_INDEFINITE} }, - [STATE_DISCHARGE_S3] = {{EC_LED_COLOR_RED, 1 * LED_ONE_SEC}, - {LED_OFF, 3 * LED_ONE_SEC} }, - [STATE_DISCHARGE_S5] = {{LED_OFF, LED_INDEFINITE} }, - [STATE_BATTERY_ERROR] = {{EC_LED_COLOR_BLUE, 2 * LED_ONE_SEC}, - {EC_LED_COLOR_RED, 2 * LED_ONE_SEC} }, - [STATE_FACTORY_TEST] = {{EC_LED_COLOR_BLUE, LED_INDEFINITE} }, -}; -BUILD_ASSERT(ARRAY_SIZE(led_bat_state_table) == LED_NUM_STATES); - -const enum ec_led_id supported_led_ids[] = { EC_LED_ID_BATTERY_LED }; - -const int supported_led_ids_count = ARRAY_SIZE(supported_led_ids); - -__override void led_set_color_battery(enum ec_led_colors color) -{ - switch (color) { - case EC_LED_COLOR_BLUE: - gpio_set_level(GPIO_LED_FULL_L, LED_ON_LVL); - gpio_set_level(GPIO_LED_CHRG_L, LED_OFF_LVL); - break; - case EC_LED_COLOR_RED: - gpio_set_level(GPIO_LED_FULL_L, LED_OFF_LVL); - gpio_set_level(GPIO_LED_CHRG_L, LED_ON_LVL); - break; - default: /* LED_OFF and other unsupported colors */ - gpio_set_level(GPIO_LED_FULL_L, LED_OFF_LVL); - gpio_set_level(GPIO_LED_CHRG_L, LED_OFF_LVL); - break; - } -} - -void led_get_brightness_range(enum ec_led_id led_id, uint8_t *brightness_range) -{ - brightness_range[EC_LED_COLOR_BLUE] = 1; - brightness_range[EC_LED_COLOR_RED] = 1; -} - -int led_set_brightness(enum ec_led_id led_id, const uint8_t *brightness) -{ - if (brightness[EC_LED_COLOR_BLUE] != 0) - led_set_color_battery(EC_LED_COLOR_BLUE); - else if (brightness[EC_LED_COLOR_RED] != 0) - led_set_color_battery(EC_LED_COLOR_RED); - else - led_set_color_battery(LED_OFF); - - return EC_SUCCESS; -} diff --git a/board/trembyle/vif_override.xml b/board/trembyle/vif_override.xml deleted file mode 100644 index 32736caf64..0000000000 --- a/board/trembyle/vif_override.xml +++ /dev/null @@ -1,3 +0,0 @@ -<!-- Add VIF field overrides here. See genvif.c and the Vendor Info File - Definition from the USB-IF. ---> |