diff options
Diffstat (limited to 'board/vell/board.h')
| -rw-r--r-- | board/vell/board.h | 144 |
1 files changed, 65 insertions, 79 deletions
diff --git a/board/vell/board.h b/board/vell/board.h index eabb09d75a..a17be43a50 100644 --- a/board/vell/board.h +++ b/board/vell/board.h @@ -1,4 +1,4 @@ -/* Copyright 2021 The Chromium OS Authors. All rights reserved. +/* Copyright 2021 The ChromiumOS Authors * Use of this source code is governed by a BSD-style license that can be * found in the LICENSE file. */ @@ -45,13 +45,14 @@ /* Sensors without hardware FIFO are in forced mode */ #define CONFIG_ACCEL_FORCE_MODE_MASK BIT(CLEAR_ALS) - /* USB Type C and USB PD defines */ #define CONFIG_USB_PD_REQUIRE_AP_MODE_ENTRY #define CONFIG_IO_EXPANDER #define CONFIG_IO_EXPANDER_NCT38XX -#define CONFIG_IO_EXPANDER_PORT_COUNT 4 +#define CONFIG_IO_EXPANDER_PORT_COUNT 4 + +#define CONFIG_USB_PD_FRS_PPC #define CONFIG_USBC_RETIMER_INTEL_BB @@ -61,16 +62,16 @@ #define CONFIG_SYV682X_HV_ILIM SYV682X_HV_ILIM_5_50 /* TODO: b/177608416 - measure and check these values on brya */ -#define PD_POWER_SUPPLY_TURN_ON_DELAY 30000 /* us */ -#define PD_POWER_SUPPLY_TURN_OFF_DELAY 30000 /* us */ -#define PD_VCONN_SWAP_DELAY 5000 /* us */ +#define PD_POWER_SUPPLY_TURN_ON_DELAY 30000 /* us */ +#define PD_POWER_SUPPLY_TURN_OFF_DELAY 30000 /* us */ +#define PD_VCONN_SWAP_DELAY 5000 /* us */ /* USB Type C and USB PD defines */ -#define PD_OPERATING_POWER_MW 15000 -#define PD_MAX_CURRENT_MA 5000 -#define PD_MAX_VOLTAGE_MV 20000 +#define PD_OPERATING_POWER_MW 15000 +#define PD_MAX_CURRENT_MA 5000 +#define PD_MAX_VOLTAGE_MV 20000 /* Max Power = 100 W */ -#define PD_MAX_POWER_MW ((PD_MAX_VOLTAGE_MV * PD_MAX_CURRENT_MA) / 1000) +#define PD_MAX_POWER_MW ((PD_MAX_VOLTAGE_MV * PD_MAX_CURRENT_MA) / 1000) /* * Macros for GPIO signals used in common code that don't match the @@ -78,84 +79,78 @@ * then redefined here to so it's more clear which signal is being used for * which purpose. */ -#define GPIO_AC_PRESENT GPIO_ACOK_OD -#define GPIO_CPU_PROCHOT GPIO_EC_PROCHOT_ODL -#define GPIO_EC_INT_L GPIO_EC_PCH_INT_ODL -#define GPIO_ENABLE_BACKLIGHT GPIO_EC_EN_EDP_BL -#define GPIO_ENTERING_RW GPIO_EC_ENTERING_RW -#define GPIO_KBD_KSO2 GPIO_EC_KSO_02_INV -#define GPIO_PACKET_MODE_EN GPIO_EC_GSC_PACKET_MODE -#define GPIO_PCH_PWRBTN_L GPIO_EC_PCH_PWR_BTN_ODL -#define GPIO_PCH_RSMRST_L GPIO_EC_PCH_RSMRST_L -#define GPIO_PCH_RTCRST GPIO_EC_PCH_RTCRST -#define GPIO_PCH_SLP_S0_L GPIO_SYS_SLP_S0IX_L -#define GPIO_PCH_SLP_S3_L GPIO_SLP_S3_L -#define GPIO_TEMP_SENSOR_POWER GPIO_SEQ_EC_DSW_PWROK +#define GPIO_AC_PRESENT GPIO_ACOK_OD +#define GPIO_CPU_PROCHOT GPIO_EC_PROCHOT_ODL +#define GPIO_EC_INT_L GPIO_EC_PCH_INT_ODL +#define GPIO_ENABLE_BACKLIGHT GPIO_EC_EN_EDP_BL +#define GPIO_ENTERING_RW GPIO_EC_ENTERING_RW +#define GPIO_KBD_KSO2 GPIO_EC_KSO_02_INV +#define GPIO_PACKET_MODE_EN GPIO_EC_GSC_PACKET_MODE +#define GPIO_PCH_PWRBTN_L GPIO_EC_PCH_PWR_BTN_ODL +#define GPIO_PCH_RSMRST_L GPIO_EC_PCH_RSMRST_L +#define GPIO_PCH_RTCRST GPIO_EC_PCH_RTCRST +#define GPIO_PCH_SLP_S0_L GPIO_SYS_SLP_S0IX_L +#define GPIO_PCH_SLP_S3_L GPIO_SLP_S3_L +#define GPIO_TEMP_SENSOR_POWER GPIO_SEQ_EC_DSW_PWROK /* * GPIO_EC_PCH_INT_ODL is used for MKBP events as well as a PCH wakeup * signal. */ -#define GPIO_PCH_WAKE_L GPIO_EC_PCH_INT_ODL -#define GPIO_PG_EC_ALL_SYS_PWRGD GPIO_SEQ_EC_ALL_SYS_PG -#define GPIO_PG_EC_DSW_PWROK GPIO_SEQ_EC_DSW_PWROK -#define GPIO_PG_EC_RSMRST_ODL GPIO_SEQ_EC_RSMRST_ODL -#define GPIO_POWER_BUTTON_L GPIO_GSC_EC_PWR_BTN_ODL -#define GPIO_SYS_RESET_L GPIO_SYS_RST_ODL -#define GPIO_WP_L GPIO_EC_WP_ODL -#define GPIO_RIGHT_LED_AMBER_L GPIO_LED_1_L -#define GPIO_RIGHT_LED_WHITE_L GPIO_LED_2_L -#define GPIO_LEFT_LED_AMBER_L GPIO_LED_3_L -#define GPIO_LEFT_LED_WHITE_L GPIO_LED_4_L +#define GPIO_PCH_WAKE_L GPIO_EC_PCH_INT_ODL +#define GPIO_PG_EC_ALL_SYS_PWRGD GPIO_SEQ_EC_ALL_SYS_PG +#define GPIO_PG_EC_DSW_PWROK GPIO_SEQ_EC_DSW_PWROK +#define GPIO_PG_EC_RSMRST_ODL GPIO_SEQ_EC_RSMRST_ODL +#define GPIO_POWER_BUTTON_L GPIO_GSC_EC_PWR_BTN_ODL +#define GPIO_SYS_RESET_L GPIO_SYS_RST_ODL +#define GPIO_WP_L GPIO_EC_WP_ODL +#define GPIO_RIGHT_LED_AMBER_L GPIO_LED_1_L +#define GPIO_RIGHT_LED_WHITE_L GPIO_LED_2_L +#define GPIO_LEFT_LED_AMBER_L GPIO_LED_3_L +#define GPIO_LEFT_LED_WHITE_L GPIO_LED_4_L /* System has back-lit keyboard */ #define CONFIG_PWM_KBLIGHT /* I2C Bus Configuration */ -#define I2C_PORT_SENSOR NPCX_I2C_PORT0_0 +#define I2C_PORT_SENSOR NPCX_I2C_PORT0_0 -#define I2C_PORT_USB_C0_C1_TCPC NPCX_I2C_PORT1_0 -#define I2C_PORT_USB_C2_C3_TCPC NPCX_I2C_PORT4_1 +#define I2C_PORT_USB_C0_C1_TCPC NPCX_I2C_PORT1_0 +#define I2C_PORT_USB_C2_C3_TCPC NPCX_I2C_PORT4_1 -#define I2C_PORT_USB_C0_C1_PPC NPCX_I2C_PORT2_0 -#define I2C_PORT_USB_C2_C3_PPC NPCX_I2C_PORT6_1 +#define I2C_PORT_USB_C0_C1_PPC NPCX_I2C_PORT2_0 +#define I2C_PORT_USB_C2_C3_PPC NPCX_I2C_PORT6_1 -#define I2C_PORT_USB_C0_C1_BC12 NPCX_I2C_PORT2_0 -#define I2C_PORT_USB_C2_C3_BC12 NPCX_I2C_PORT6_1 +#define I2C_PORT_USB_C0_C1_BC12 NPCX_I2C_PORT2_0 +#define I2C_PORT_USB_C2_C3_BC12 NPCX_I2C_PORT6_1 -#define I2C_PORT_USB_C0_C1_MUX NPCX_I2C_PORT3_0 -#define I2C_PORT_USB_C2_C3_MUX NPCX_I2C_PORT3_0 +#define I2C_PORT_USB_C0_C1_MUX NPCX_I2C_PORT3_0 +#define I2C_PORT_USB_C2_C3_MUX NPCX_I2C_PORT3_0 -#define I2C_PORT_BATTERY NPCX_I2C_PORT5_0 -#define I2C_PORT_CHARGER NPCX_I2C_PORT7_0 -#define I2C_PORT_EEPROM NPCX_I2C_PORT7_0 +#define I2C_PORT_BATTERY NPCX_I2C_PORT5_0 +#define I2C_PORT_CHARGER NPCX_I2C_PORT7_0 +#define I2C_PORT_EEPROM NPCX_I2C_PORT7_0 -#define I2C_ADDR_EEPROM_FLAGS 0x50 +#define I2C_ADDR_EEPROM_FLAGS 0x50 /* * see b/174768555#comment22 */ -#define USBC_PORT_C0_BB_RETIMER_I2C_ADDR 0x56 -#define USBC_PORT_C1_BB_RETIMER_I2C_ADDR 0x57 -#define USBC_PORT_C2_BB_RETIMER_I2C_ADDR 0x58 -#define USBC_PORT_C3_BB_RETIMER_I2C_ADDR 0x59 +#define USBC_PORT_C0_BB_RETIMER_I2C_ADDR 0x56 +#define USBC_PORT_C1_BB_RETIMER_I2C_ADDR 0x57 +#define USBC_PORT_C2_BB_RETIMER_I2C_ADDR 0x58 +#define USBC_PORT_C3_BB_RETIMER_I2C_ADDR 0x59 /* Enabling Thunderbolt-compatible mode */ #define CONFIG_USB_PD_TBT_COMPAT_MODE /* Enabling USB4 mode */ #define CONFIG_USB_PD_USB4 +#define CONFIG_USB_PD_DATA_RESET_MSG -/* - * TODO: b/220634230, Disable BBR firmware update temporally, - * revert this patch once confirm BBR firmware update is ready - * on kernel. - */ /* Retimer */ -#if 0 #define CONFIG_USBC_RETIMER_FW_UPDATE -#endif /* Thermal features */ #define CONFIG_THERMISTOR @@ -164,22 +159,23 @@ #define CONFIG_STEINHART_HART_3V3_30K9_47K_4050B /* Fan features */ -#define CONFIG_FANS FAN_CH_COUNT +#define CONFIG_FANS FAN_CH_COUNT +#define CONFIG_FAN_BYPASS_SLOW_RESPONSE #define CONFIG_CUSTOM_FAN_CONTROL -#define RPM_DEVIATION 1 +#define RPM_DEVIATION 1 /* Charger defines */ #define CONFIG_CHARGER_ISL9241 #define CONFIG_CHARGE_RAMP_SW -#define CONFIG_CHARGER_SENSE_RESISTOR 5 -#define CONFIG_CHARGER_SENSE_RESISTOR_AC 10 +#define CONFIG_CHARGER_SENSE_RESISTOR 5 +#define CONFIG_CHARGER_SENSE_RESISTOR_AC 10 /* Keyboard features */ #define CONFIG_KEYBOARD_FACTORY_TEST #define CONFIG_KEYBOARD_REFRESH_ROW3 #undef CONFIG_BATT_HOST_SHUTDOWN_PERCENTAGE -#define CONFIG_BATT_HOST_SHUTDOWN_PERCENTAGE 3 +#define CONFIG_BATT_HOST_SHUTDOWN_PERCENTAGE 3 /* * Older boards have a different ADC assignment. @@ -189,7 +185,7 @@ #ifndef __ASSEMBLER__ -#include "gpio_signal.h" /* needed by registers.h */ +#include "gpio_signal.h" /* needed by registers.h */ #include "registers.h" #include "usbc_config.h" @@ -211,11 +207,7 @@ enum temp_sensor_id { TEMP_SENSOR_COUNT }; -enum sensor_id { - CLEAR_ALS = 0, - RGB_ALS, - SENSOR_COUNT -}; +enum sensor_id { CLEAR_ALS = 0, RGB_ALS, SENSOR_COUNT }; enum ioex_port { IOEX_C0_NCT38XX = 0, @@ -232,20 +224,14 @@ enum battery_type { }; enum pwm_channel { - PWM_CH_KBLIGHT = 0, /* PWM3 */ - PWM_CH_FAN, /* PWM5 */ + PWM_CH_KBLIGHT = 0, /* PWM3 */ + PWM_CH_FAN, /* PWM5 */ PWM_CH_COUNT }; -enum fan_channel { - FAN_CH_0 = 0, - FAN_CH_COUNT -}; +enum fan_channel { FAN_CH_0 = 0, FAN_CH_COUNT }; -enum mft_channel { - MFT_CH_0 = 0, - MFT_CH_COUNT -}; +enum mft_channel { MFT_CH_0 = 0, MFT_CH_COUNT }; #ifdef CONFIG_KEYBOARD_FACTORY_TEST extern const int keyboard_factory_scan_pins[][2]; |