summaryrefslogtreecommitdiff
path: root/board/volet
diff options
context:
space:
mode:
Diffstat (limited to 'board/volet')
-rw-r--r--board/volet/battery.c125
-rw-r--r--board/volet/board.c497
-rw-r--r--board/volet/board.h197
-rw-r--r--board/volet/build.mk17
-rw-r--r--board/volet/ec.tasklist26
-rw-r--r--board/volet/gpio.inc184
-rw-r--r--board/volet/led.c79
-rw-r--r--board/volet/sensors.c247
-rw-r--r--board/volet/vif_override.xml158
9 files changed, 0 insertions, 1530 deletions
diff --git a/board/volet/battery.c b/board/volet/battery.c
deleted file mode 100644
index 2e4fb7dc71..0000000000
--- a/board/volet/battery.c
+++ /dev/null
@@ -1,125 +0,0 @@
-/* Copyright 2021 The Chromium OS Authors. All rights reserved.
- * Use of this source code is governed by a BSD-style license that can be
- * found in the LICENSE file.
- *
- * Battery pack vendor provided charging profile
- */
-
-#include "battery_fuel_gauge.h"
-#include "common.h"
-#include "util.h"
-
-/*
- * Battery info for all Volteer battery types. Note that the fields
- * start_charging_min/max and charging_min/max are not used for the charger.
- * The effective temperature limits are given by discharging_min/max_c.
- *
- * Fuel Gauge (FG) parameters which are used for determining if the battery
- * is connected, the appropriate ship mode (battery cutoff) command, and the
- * charge/discharge FETs status.
- *
- * Ship mode (battery cutoff) requires 2 writes to the appropriate smart battery
- * register. For some batteries, the charge/discharge FET bits are set when
- * charging/discharging is active, in other types, these bits set mean that
- * charging/discharging is disabled. Therefore, in addition to the mask for
- * these bits, a disconnect value must be specified. Note that for TI fuel
- * gauge, the charge/discharge FET status is found in Operation Status (0x54),
- * but a read of Manufacturer Access (0x00) will return the lower 16 bits of
- * Operation status which contains the FET status bits.
- *
- * The assumption for battery types supported is that the charge/discharge FET
- * status can be read with a sb_read() command and therefore, only the register
- * address, mask, and disconnect value need to be provided.
- */
-const struct board_batt_params board_battery_info[] = {
- /* AP19B8M */
- [BATTERY_AP19B8M] = {
- .fuel_gauge = {
- .manuf_name = "LGC KT0030G024",
- .ship_mode = {
- .reg_addr = 0x3A,
- .reg_data = { 0xC574, 0xC574 },
- },
- .fet = {
- .reg_addr = 0x43,
- .reg_mask = 0x0001,
- .disconnect_val = 0x0,
- .cfet_mask = 0x0002,
- .cfet_off_val = 0x0000,
- }
- },
- .batt_info = {
- .voltage_max = 13350,
- .voltage_normal = 11610,
- .voltage_min = 9000,
- .precharge_current = 256,
- .start_charging_min_c = 0,
- .start_charging_max_c = 50,
- .charging_min_c = 0,
- .charging_max_c = 60,
- .discharging_min_c = -20,
- .discharging_max_c = 75,
- },
- },
- /* LGC AP18C8K Battery Information */
- [BATTERY_LGC_AP18C8K] = {
- .fuel_gauge = {
- .manuf_name = "LGC KT0030G020",
- .ship_mode = {
- .reg_addr = 0x3A,
- .reg_data = { 0xC574, 0xC574 },
- },
- .fet = {
- .reg_addr = 0x43,
- .reg_mask = 0x0001,
- .disconnect_val = 0x0,
- .cfet_mask = 0x0002,
- .cfet_off_val = 0x0000,
- },
- },
- .batt_info = {
- .voltage_max = 13050,
- .voltage_normal = 11250,
- .voltage_min = 9000,
- .precharge_current = 256,
- .start_charging_min_c = 0,
- .start_charging_max_c = 50,
- .charging_min_c = 0,
- .charging_max_c = 60,
- .discharging_min_c = -20,
- .discharging_max_c = 75,
- },
- },
- /* COSMX AP20CBL Battery Information */
- [BATTERY_COSMX_AP20CBL] = {
- .fuel_gauge = {
- .manuf_name = "COSMX KT0030B002",
- .device_name = "AP20CBL",
- .ship_mode = {
- .reg_addr = 0x3A,
- .reg_data = { 0xC574, 0xC574 },
- },
- .fet = {
- .mfgacc_support = 1,
- .reg_addr = 0x0,
- .reg_mask = 0x2000,
- .disconnect_val = 0x2000,
- },
- },
- .batt_info = {
- .voltage_max = 13200,
- .voltage_normal = 11550,
- .voltage_min = 9000,
- .precharge_current = 256,
- .start_charging_min_c = 0,
- .start_charging_max_c = 50,
- .charging_min_c = 0,
- .charging_max_c = 60,
- .discharging_min_c = -20,
- .discharging_max_c = 75,
- },
- },
-};
-BUILD_ASSERT(ARRAY_SIZE(board_battery_info) == BATTERY_TYPE_COUNT);
-
-const enum battery_type DEFAULT_BATTERY_TYPE = BATTERY_AP19B8M;
diff --git a/board/volet/board.c b/board/volet/board.c
deleted file mode 100644
index a47bd3d8c6..0000000000
--- a/board/volet/board.c
+++ /dev/null
@@ -1,497 +0,0 @@
-/* Copyright 2021 The Chromium OS Authors. All rights reserved.
- * Use of this source code is governed by a BSD-style license that can be
- * found in the LICENSE file.
- */
-
-/* Volteer board-specific configuration */
-#include "button.h"
-#include "common.h"
-#include "accelgyro.h"
-#include "cbi_ec_fw_config.h"
-#include "driver/accel_bma2x2.h"
-#include "driver/accelgyro_bmi160.h"
-#include "driver/als_tcs3400.h"
-#include "driver/bc12/pi3usb9201.h"
-#include "driver/ppc/syv682x.h"
-#include "driver/sync.h"
-#include "driver/tcpm/ps8xxx.h"
-#include "driver/tcpm/rt1715.h"
-#include "driver/tcpm/tcpci.h"
-#include "extpower.h"
-#include "fan.h"
-#include "fan_chip.h"
-#include "gpio.h"
-#include "hooks.h"
-#include "keyboard_raw.h"
-#include "keyboard_scan.h"
-#include "lid_switch.h"
-#include "power.h"
-#include "power_button.h"
-#include "pwm.h"
-#include "pwm_chip.h"
-#include "switch.h"
-#include "system.h"
-#include "task.h"
-#include "tablet_mode.h"
-#include "throttle_ap.h"
-#include "uart.h"
-#include "usb_mux.h"
-#include "usb_pd.h"
-#include "usb_pd_tbt.h"
-#include "usb_pd_tcpm.h"
-#include "usbc_ppc.h"
-#include "util.h"
-
-#include "gpio_list.h" /* Must come after other header files. */
-
-#define CPRINTS(format, args...) cprints(CC_CHIPSET, format, ## args)
-
-static const struct ec_response_keybd_config volet_kb = {
- .num_top_row_keys = 10,
- .action_keys = {
- TK_BACK, /* T1 */
- TK_REFRESH, /* T2 */
- TK_FULLSCREEN, /* T3 */
- TK_OVERVIEW, /* T4 */
- TK_SNAPSHOT, /* T5 */
- TK_BRIGHTNESS_DOWN, /* T6 */
- TK_BRIGHTNESS_UP, /* T7 */
- TK_VOL_MUTE, /* T8 */
- TK_VOL_DOWN, /* T9 */
- TK_VOL_UP, /* T10 */
- },
- .capabilities = KEYBD_CAP_SCRNLOCK_KEY,
-};
-
-static const struct ec_response_keybd_config volet_kb_num = {
- .num_top_row_keys = 10,
- .action_keys = {
- TK_BACK, /* T1 */
- TK_REFRESH, /* T2 */
- TK_FULLSCREEN, /* T3 */
- TK_OVERVIEW, /* T4 */
- TK_SNAPSHOT, /* T5 */
- TK_BRIGHTNESS_DOWN, /* T6 */
- TK_BRIGHTNESS_UP, /* T7 */
- TK_VOL_MUTE, /* T8 */
- TK_VOL_DOWN, /* T9 */
- TK_VOL_UP, /* T10 */
- },
- .capabilities = KEYBD_CAP_SCRNLOCK_KEY | KEYBD_CAP_NUMERIC_KEYPAD,
-};
-
-__override const struct ec_response_keybd_config
-*board_vivaldi_keybd_config(void)
-{
- if (!ec_cfg_has_numeric_pad())
- return &volet_kb;
- else
- return &volet_kb_num;
-}
-
-/* Keyboard scan setting */
-__override struct keyboard_scan_config keyscan_config = {
- /* Increase from 50 us, because KSO_02 passes through the H1. */
- .output_settle_us = 80,
- /* Other values should be the same as the default configuration. */
- .debounce_down_us = 9 * MSEC,
- .debounce_up_us = 30 * MSEC,
- .scan_period_us = 3 * MSEC,
- .min_post_scan_delay_us = 1000,
- .poll_timeout_us = 100 * MSEC,
- .actual_key_mask = {
- 0x1c, 0xfe, 0xff, 0xff, 0xff, 0xf5, 0xff,
- 0xa4, 0xff, 0xfe, 0x55, 0xfe, 0xff, 0xff,
- 0xff, /* full set */
- },
-};
-
-/*
- * We have total 30 pins for keyboard connecter {-1, -1} mean
- * the N/A pin that don't consider it and reserve index 0 area
- * that we don't have pin 0.
- */
-const int keyboard_factory_scan_pins[][2] = {
- {-1, -1}, {0, 5}, {1, 1}, {1, 0}, {0, 6},
- {0, 7}, {-1, -1}, {-1, -1}, {1, 4}, {1, 3},
- {-1, -1}, {1, 6}, {1, 7}, {3, 1}, {2, 0},
- {1, 5}, {2, 6}, {2, 7}, {2, 1}, {2, 4},
- {2, 5}, {1, 2}, {2, 3}, {2, 2}, {3, 0},
- {-1, -1}, {0, 4}, {-1, -1}, {8, 2}, {-1, -1},
- {-1, -1},
-};
-const int keyboard_factory_scan_pins_used =
- ARRAY_SIZE(keyboard_factory_scan_pins);
-
-__override uint32_t board_override_feature_flags0(uint32_t flags0)
-{
- /*
- * Remove keyboard backlight feature for devices that don't support it.
- */
- if (!ec_cfg_has_keyboard_backlight())
- return (flags0 & ~EC_FEATURE_MASK_0(EC_FEATURE_PWM_KEYB));
- else
- return flags0;
-}
-
-/******************************************************************************/
-/*
- * FW_CONFIG defaults for Voxel if the CBI data is not initialized.
- */
-union volteer_cbi_fw_config fw_config_defaults = {
- .usb_db = DB_USB4_GEN3,
-};
-
-/******************************************************************************/
-/* Physical fans. These are logically separate from pwm_channels. */
-
-const struct fan_conf fan_conf_0 = {
- .flags = FAN_USE_RPM_MODE,
- .ch = MFT_CH_0, /* Use MFT id to control fan */
- .pgood_gpio = -1,
- .enable_gpio = GPIO_EN_PP5000_FAN,
-};
-
-/*
- * Fan specs from datasheet:
- * Max speed 5900 rpm (+/- 7%), minimum duty cycle 30%.
- * Minimum speed not specified by RPM. Set minimum RPM to max speed (with
- * margin) x 30%.
- * 5900 x 1.07 x 0.30 = 1894, round up to 1900
- * reference that temperature and fan settings
- * are derived from data in b/167523658#39
- */
-const struct fan_rpm fan_rpm_0 = {
- .rpm_min = 2100,
- .rpm_start = 2100,
- .rpm_max = 5800,
-};
-
-const struct fan_t fans[FAN_CH_COUNT] = {
- [FAN_CH_0] = {
- .conf = &fan_conf_0,
- .rpm = &fan_rpm_0,
- },
-};
-
-/******************************************************************************/
-/* EC thermal management configuration */
-
-/*
- * Reference that temperature and fan settings
- * are derived from data in b/167523658#39
- */
-const static struct ec_thermal_config thermal_cpu = {
- .temp_host = {
- [EC_TEMP_THRESH_HIGH] = C_TO_K(75),
- [EC_TEMP_THRESH_HALT] = C_TO_K(85),
- },
- .temp_host_release = {
- [EC_TEMP_THRESH_HIGH] = C_TO_K(68),
- },
- .temp_fan_off = C_TO_K(25),
- .temp_fan_max = C_TO_K(90),
-};
-
-struct ec_thermal_config thermal_params[] = {
- [TEMP_SENSOR_1_CHARGER] = thermal_cpu,
- [TEMP_SENSOR_2_PP3300_REGULATOR] = thermal_cpu,
- [TEMP_SENSOR_3_DDR_SOC] = thermal_cpu,
- [TEMP_SENSOR_4_FAN] = thermal_cpu,
-};
-BUILD_ASSERT(ARRAY_SIZE(thermal_params) == TEMP_SENSOR_COUNT);
-
-/******************************************************************************/
-/* MFT channels. These are logically separate from pwm_channels. */
-const struct mft_t mft_channels[] = {
- [MFT_CH_0] = {
- .module = NPCX_MFT_MODULE_1,
- .clk_src = TCKC_LFCLK,
- .pwm_id = PWM_CH_FAN,
- },
-};
-BUILD_ASSERT(ARRAY_SIZE(mft_channels) == MFT_CH_COUNT);
-
-/******************************************************************************/
-/* I2C port map configuration */
-const struct i2c_port_t i2c_ports[] = {
- {
- .name = "sensor",
- .port = I2C_PORT_SENSOR,
- .kbps = 400,
- .scl = GPIO_EC_I2C0_SENSOR_SCL,
- .sda = GPIO_EC_I2C0_SENSOR_SDA,
- },
- {
- .name = "usb_c0",
- .port = I2C_PORT_USB_C0,
- .kbps = 1000,
- .scl = GPIO_EC_I2C1_USB_C0_SCL,
- .sda = GPIO_EC_I2C1_USB_C0_SDA,
- },
- {
- .name = "usb_c1",
- .port = I2C_PORT_USB_C1,
- .kbps = 1000,
- .scl = GPIO_EC_I2C2_USB_C1_SCL,
- .sda = GPIO_EC_I2C2_USB_C1_SDA,
- },
- {
- .name = "power",
- .port = I2C_PORT_POWER,
- .kbps = 100,
- .scl = GPIO_EC_I2C5_POWER_SCL,
- .sda = GPIO_EC_I2C5_POWER_SDA,
- },
- {
- .name = "eeprom",
- .port = I2C_PORT_EEPROM,
- .kbps = 400,
- .scl = GPIO_EC_I2C7_EEPROM_SCL,
- .sda = GPIO_EC_I2C7_EEPROM_SDA,
- },
-};
-const unsigned int i2c_ports_used = ARRAY_SIZE(i2c_ports);
-
-/******************************************************************************/
-/* PWM configuration */
-const struct pwm_t pwm_channels[] = {
- [PWM_CH_FAN] = {
- .channel = 5,
- .flags = PWM_CONFIG_OPEN_DRAIN,
- .freq = 25000
- },
- [PWM_CH_KBLIGHT] = {
- .channel = 3,
- .flags = 0,
- /*
- * Set PWM frequency to multiple of 50 Hz and 60 Hz to prevent
- * flicker. Higher frequencies consume similar average power to
- * lower PWM frequencies, but higher frequencies record a much
- * lower maximum power.
- */
- .freq = 2400,
- },
-};
-BUILD_ASSERT(ARRAY_SIZE(pwm_channels) == PWM_CH_COUNT);
-
-static void kb_backlight_enable(void)
-{
- if (ec_cfg_has_keyboard_backlight())
- gpio_set_level(GPIO_EC_KB_BL_EN, 1);
-}
-DECLARE_HOOK(HOOK_CHIPSET_RESUME, kb_backlight_enable, HOOK_PRIO_DEFAULT);
-
-static void kb_backlight_disable(void)
-{
- if (ec_cfg_has_keyboard_backlight())
- gpio_set_level(GPIO_EC_KB_BL_EN, 0);
-}
-DECLARE_HOOK(HOOK_CHIPSET_SUSPEND, kb_backlight_disable, HOOK_PRIO_DEFAULT);
-
-static void ps8815_reset(void)
-{
- int val;
-
- gpio_set_level(GPIO_USB_C1_RT_RST_ODL, 0);
- msleep(GENERIC_MAX(PS8XXX_RESET_DELAY_MS,
- PS8815_PWR_H_RST_H_DELAY_MS));
- gpio_set_level(GPIO_USB_C1_RT_RST_ODL, 1);
- msleep(PS8815_FW_INIT_DELAY_MS);
-
- /*
- * b/144397088
- * ps8815 firmware 0x01 needs special configuration
- */
-
- CPRINTS("%s: patching ps8815 registers", __func__);
-
- if (i2c_read8(I2C_PORT_USB_C1,
- PS8751_I2C_ADDR1_P2_FLAGS, 0x0f, &val) == EC_SUCCESS)
- CPRINTS("ps8815: reg 0x0f was %02x", val);
-
- if (i2c_write8(I2C_PORT_USB_C1,
- PS8751_I2C_ADDR1_P2_FLAGS, 0x0f, 0x31) == EC_SUCCESS)
- CPRINTS("ps8815: reg 0x0f set to 0x31");
-
- if (i2c_read8(I2C_PORT_USB_C1,
- PS8751_I2C_ADDR1_P2_FLAGS, 0x0f, &val) == EC_SUCCESS)
- CPRINTS("ps8815: reg 0x0f now %02x", val);
-}
-
-void board_reset_pd_mcu(void)
-{
- /*
- * Only the Burnside Bridge retimers provide a reset pin, but this is
- * already handled by the bb_retimer.c driver.
- */
- ps8815_reset();
- usb_mux_hpd_update(USBC_PORT_C1, USB_PD_MUX_HPD_LVL_DEASSERTED |
- USB_PD_MUX_HPD_IRQ_DEASSERTED);
-}
-
-/******************************************************************************/
-/* USB-A charging control */
-
-const int usb_port_enable[USB_PORT_COUNT] = {
- GPIO_EN_PP5000_USBA,
-};
-
-/******************************************************************************/
-/* USBC PPC configuration */
-struct ppc_config_t ppc_chips[] = {
- [USBC_PORT_C0] = {
- .i2c_port = I2C_PORT_USB_C0,
- .i2c_addr_flags = SYV682X_ADDR0_FLAGS,
- .drv = &syv682x_drv,
- .frs_en = GPIO_USB_C0_FRS_EN,
- },
- [USBC_PORT_C1] = {
- .i2c_port = I2C_PORT_USB_C1,
- .i2c_addr_flags = SYV682X_ADDR0_FLAGS,
- .drv = &syv682x_drv,
- .frs_en = GPIO_USB_C1_FRS_EN,
- },
-};
-BUILD_ASSERT(ARRAY_SIZE(ppc_chips) == USBC_PORT_COUNT);
-unsigned int ppc_cnt = ARRAY_SIZE(ppc_chips);
-
-/******************************************************************************/
-/* PPC support routines */
-void ppc_interrupt(enum gpio_signal signal)
-{
- switch (signal) {
- case GPIO_USB_C0_PPC_INT_ODL:
- syv682x_interrupt(USBC_PORT_C0);
- break;
- case GPIO_USB_C1_PPC_INT_ODL:
- syv682x_interrupt(USBC_PORT_C1);
- default:
- break;
- }
-}
-
-__override void board_cbi_init(void)
-{
- if ((!IS_ENABLED(TEST_BUILD) && !ec_cfg_has_numeric_pad())) {
- keyboard_raw_set_cols(KEYBOARD_COLS_NO_KEYPAD);
- /* Search key is moved back to col=1,row=0 */
- keyscan_config.actual_key_mask[0] = 0x14;
- keyscan_config.actual_key_mask[1] = 0xff;
- keyscan_config.actual_key_mask[11] = 0xfa;
- keyscan_config.actual_key_mask[12] = 0xca;
- }
-}
-
-/******************************************************************************/
-/* BC1.2 charger detect configuration */
-const struct pi3usb9201_config_t pi3usb9201_bc12_chips[] = {
- [USBC_PORT_C0] = {
- .i2c_port = I2C_PORT_USB_C0,
- .i2c_addr_flags = PI3USB9201_I2C_ADDR_3_FLAGS,
- },
- [USBC_PORT_C1] = {
- .i2c_port = I2C_PORT_USB_C1,
- .i2c_addr_flags = PI3USB9201_I2C_ADDR_3_FLAGS,
- },
-};
-BUILD_ASSERT(ARRAY_SIZE(pi3usb9201_bc12_chips) == USBC_PORT_COUNT);
-
-/******************************************************************************/
-/* USBC TCPC configuration */
-const struct tcpc_config_t tcpc_config[] = {
- [USBC_PORT_C0] = {
- .bus_type = EC_BUS_TYPE_I2C,
- .i2c_info = {
- .port = I2C_PORT_USB_C0,
- .addr_flags = RT1715_I2C_ADDR_FLAGS,
- },
- .drv = &rt1715_tcpm_drv,
- },
- [USBC_PORT_C1] = {
- .bus_type = EC_BUS_TYPE_I2C,
- .i2c_info = {
- .port = I2C_PORT_USB_C1,
- .addr_flags = PS8751_I2C_ADDR1_FLAGS,
- },
- .flags = TCPC_FLAGS_TCPCI_REV2_0 |
- TCPC_FLAGS_TCPCI_REV2_0_NO_VSAFE0V,
- .drv = &ps8xxx_tcpm_drv,
- },
-};
-BUILD_ASSERT(ARRAY_SIZE(tcpc_config) == USBC_PORT_COUNT);
-BUILD_ASSERT(CONFIG_USB_PD_PORT_MAX_COUNT == USBC_PORT_COUNT);
-
-/*
- * USB3 DB mux configuration - the top level mux still needs to be set to the
- * virtual_usb_mux_driver so the AP gets notified of mux changes and updates
- * the TCSS configuration on state changes.
- */
-static const struct usb_mux usbc1_usb3_db_retimer = {
- .usb_port = USBC_PORT_C1,
- .driver = &tcpci_tcpm_usb_mux_driver,
- .hpd_update = &ps8xxx_tcpc_update_hpd_status,
- .next_mux = NULL,
-};
-
-/******************************************************************************/
-/* USBC mux configuration - Tiger Lake includes internal mux */
-const struct usb_mux usb_muxes[] = {
- [USBC_PORT_C0] = {
- .usb_port = USBC_PORT_C0,
- .driver = &virtual_usb_mux_driver,
- .hpd_update = &virtual_hpd_update,
- },
- [USBC_PORT_C1] = {
- .usb_port = USBC_PORT_C1,
- .driver = &virtual_usb_mux_driver,
- .hpd_update = &virtual_hpd_update,
- .next_mux = &usbc1_usb3_db_retimer,
- },
-};
-BUILD_ASSERT(ARRAY_SIZE(usb_muxes) == USBC_PORT_COUNT);
-
-static void board_tcpc_init(void)
-{
- /* Don't reset TCPCs after initial reset */
- if (!system_jumped_late())
- board_reset_pd_mcu();
-
- /* Enable PPC interrupts. */
- gpio_enable_interrupt(GPIO_USB_C0_PPC_INT_ODL);
- gpio_enable_interrupt(GPIO_USB_C1_PPC_INT_ODL);
-
- /* Enable TCPC interrupts. */
- gpio_enable_interrupt(GPIO_USB_C0_TCPC_INT_ODL);
- gpio_enable_interrupt(GPIO_USB_C1_TCPC_INT_ODL);
-
- /* Enable BC1.2 interrupts. */
- gpio_enable_interrupt(GPIO_USB_C0_BC12_INT_ODL);
- gpio_enable_interrupt(GPIO_USB_C1_BC12_INT_ODL);
-}
-DECLARE_HOOK(HOOK_INIT, board_tcpc_init, HOOK_PRIO_INIT_CHIPSET);
-
-/******************************************************************************/
-/* TCPC support routines */
-uint16_t tcpc_get_alert_status(void)
-{
- uint16_t status = 0;
-
- /*
- * Check which port has the ALERT line set
- */
- if (!gpio_get_level(GPIO_USB_C0_TCPC_INT_ODL))
- status |= PD_STATUS_TCPC_ALERT_0;
- if (!gpio_get_level(GPIO_USB_C1_TCPC_INT_ODL))
- status |= PD_STATUS_TCPC_ALERT_1;
-
- return status;
-}
-
-int ppc_get_alert_status(int port)
-{
- if (port == USBC_PORT_C0)
- return gpio_get_level(GPIO_USB_C0_PPC_INT_ODL) == 0;
- else
- return gpio_get_level(GPIO_USB_C1_PPC_INT_ODL) == 0;
-}
diff --git a/board/volet/board.h b/board/volet/board.h
deleted file mode 100644
index 56285989be..0000000000
--- a/board/volet/board.h
+++ /dev/null
@@ -1,197 +0,0 @@
-/* Copyright 2021 The Chromium OS Authors. All rights reserved.
- * Use of this source code is governed by a BSD-style license that can be
- * found in the LICENSE file.
- */
-
-/* Volteer board configuration */
-
-#ifndef __CROS_EC_BOARD_H
-#define __CROS_EC_BOARD_H
-
-/* Baseboard features */
-#include "baseboard.h"
-
-/* Optional features */
-#undef NPCX7_PWM1_SEL
-#define NPCX7_PWM1_SEL 0 /* GPIO C2 is not used as PWM1. */
-
-/*
- * The RAM and flash size combination on the the NPCX797FC does not leave
- * any unused flash space that can be used to store the .init_rom section.
- */
-#undef CONFIG_CHIP_INIT_ROM_REGION
-
-#define CONFIG_VBOOT_EFS2
-
-#define CONFIG_POWER_BUTTON
-
-#undef CONFIG_UART_TX_BUF_SIZE
-#define CONFIG_UART_TX_BUF_SIZE 4096
-
-/* Chipset features */
-#define CONFIG_POWER_PP5000_CONTROL
-
-/* LED defines */
-#define CONFIG_LED_ONOFF_STATES
-
-/* Keyboard features */
-#define CONFIG_KEYBOARD_FACTORY_TEST
-#define CONFIG_KEYBOARD_REFRESH_ROW3
-
-/* Keyboard backliht */
-#define CONFIG_PWM
-#define CONFIG_PWM_KBLIGHT
-
-/* Sensors */
-#define CONFIG_DYNAMIC_MOTION_SENSOR_COUNT
-/* BMI160 Base accel/gyro */
-#define CONFIG_ACCELGYRO_BMI160
-#define CONFIG_ACCELGYRO_ICM426XX /* Base accel second source*/
-#define CONFIG_ACCELGYRO_BMI160_INT_EVENT \
- TASK_EVENT_MOTION_SENSOR_INTERRUPT(BASE_ACCEL)
-#define CONFIG_ACCELGYRO_ICM426XX_INT_EVENT \
- TASK_EVENT_MOTION_SENSOR_INTERRUPT(BASE_ACCEL)
-
-/* Lid operates in forced mode, base in FIFO */
-#define CONFIG_ACCEL_FORCE_MODE_MASK BIT(LID_ACCEL)
-
-/* BMA253 Lid accel */
-#define CONFIG_ACCEL_KX022 /* Lid accel */
-#define CONFIG_ACCEL_BMA255
-#define CONFIG_LID_ANGLE
-#define CONFIG_LID_ANGLE_UPDATE
-#define CONFIG_LID_ANGLE_SENSOR_BASE BASE_ACCEL
-#define CONFIG_LID_ANGLE_SENSOR_LID LID_ACCEL
-
-/* USB Type C and USB PD defines */
-#define CONFIG_USB_PD_PORT_MAX_COUNT 2
-
-#define PD_POWER_SUPPLY_TURN_ON_DELAY 30000 /* us */
-#define PD_POWER_SUPPLY_TURN_OFF_DELAY 30000 /* us */
-
-/*
- * SN5S30 PPC supports up to 24V VBUS source and sink, however passive USB-C
- * cables only support up to 60W.
- */
-#define PD_OPERATING_POWER_MW 15000
-#define PD_MAX_POWER_MW 60000
-#define PD_MAX_CURRENT_MA 3000
-#define PD_MAX_VOLTAGE_MV 20000
-
-#define CONFIG_USB_PD_REQUIRE_AP_MODE_ENTRY
-#ifdef BOARD_VOXEL_ECMODEENTRY
-#undef CONFIG_USB_PD_REQUIRE_AP_MODE_ENTRY
-#endif
-
-/* Enabling Thunderbolt-compatible mode */
-#define CONFIG_USB_PD_TBT_COMPAT_MODE
-
-/* USB Type A Features */
-#define USB_PORT_COUNT 1
-#define CONFIG_USB_PORT_POWER_DUMB
-
-/* USBC PPC*/
-#define CONFIG_USBC_PPC_SYV682X /* USBC port C0/C1 */
-#define CONFIG_USB_PD_FRS_PPC
-#undef CONFIG_USB_PD_TCPC_RUNTIME_CONFIG
-#undef CONFIG_USB_PD_TCPM_TUSB422
-#undef CONFIG_USB_MUX_RUNTIME_CONFIG
-
-/* BC 1.2 */
-
-/* Volume Button feature */
-
-/* Fan features */
-
-/* charger defines */
-#define CONFIG_CHARGER_SENSE_RESISTOR 10
-#define CONFIG_CHARGER_SENSE_RESISTOR_AC 10
-
-/* Retimer */
-#undef CONFIG_USBC_RETIMER_INTEL_BB
-#undef CONFIG_USBC_RETIMER_INTEL_BB_RUNTIME_CONFIG
-
-/*
- * Macros for GPIO signals used in common code that don't match the
- * schematic names. Signal names in gpio.inc match the schematic and are
- * then redefined here to so it's more clear which signal is being used for
- * which purpose.
- */
-#define GPIO_AC_PRESENT GPIO_ACOK_OD
-#define GPIO_EC_INT_L GPIO_EC_PCH_INT_ODL
-#define GPIO_EN_PP5000 GPIO_EN_PP5000_A
-#define GPIO_ENTERING_RW GPIO_EC_ENTERING_RW
-#define GPIO_LID_OPEN GPIO_EC_LID_OPEN
-#define GPIO_KBD_KSO2 GPIO_EC_KSO_02_INV
-#define GPIO_PACKET_MODE_EN GPIO_EC_H1_PACKET_MODE
-#define GPIO_PCH_WAKE_L GPIO_EC_PCH_WAKE_ODL
-#define GPIO_PCH_PWRBTN_L GPIO_EC_PCH_PWR_BTN_ODL
-#define GPIO_PCH_RSMRST_L GPIO_EC_PCH_RSMRST_ODL
-#define GPIO_PCH_RTCRST GPIO_EC_PCH_RTCRST
-#define GPIO_PCH_SLP_S0_L GPIO_SLP_S0_L
-#define GPIO_PCH_SLP_S3_L GPIO_SLP_S3_L
-#define GPIO_PCH_DSW_PWROK GPIO_EC_PCH_DSW_PWROK
-#define GPIO_POWER_BUTTON_L GPIO_H1_EC_PWR_BTN_ODL
-#define GPIO_RSMRST_L_PGOOD GPIO_PG_EC_RSMRST_ODL
-#define GPIO_CPU_PROCHOT GPIO_EC_PROCHOT_ODL
-#define GPIO_SYS_RESET_L GPIO_SYS_RST_ODL
-#define GPIO_WP_L GPIO_EC_WP_L
-#define GPIO_USB_C1_BC12_INT_ODL GPIO_USB_C1_MIX_INT_ODL
-#define GPIO_VOLUME_UP_L GPIO_EC_VOLUP_BTN_ODL
-#define GPIO_VOLUME_DOWN_L GPIO_EC_VOLDN_BTN_ODL
-#define GMR_TABLET_MODE_GPIO_L GPIO_TABLET_MODE_L
-
-/* I2C Bus Configuration */
-#define CONFIG_I2C
-#define I2C_PORT_ACCEL I2C_PORT_SENSOR
-#define I2C_PORT_SENSOR NPCX_I2C_PORT0_0
-#define I2C_PORT_USB_C0 NPCX_I2C_PORT1_0
-#define I2C_PORT_USB_C1 NPCX_I2C_PORT2_0
-#define I2C_PORT_POWER NPCX_I2C_PORT5_0
-#define I2C_PORT_EEPROM NPCX_I2C_PORT7_0
-
-#define I2C_PORT_BATTERY I2C_PORT_POWER
-#define I2C_PORT_CHARGER I2C_PORT_EEPROM
-
-#define I2C_ADDR_EEPROM_FLAGS 0x50
-#define CONFIG_I2C_CONTROLLER
-
-
-#ifndef __ASSEMBLER__
-
-#include "gpio_signal.h"
-#include "registers.h"
-
-enum battery_type {
- BATTERY_AP19B8M,
- BATTERY_LGC_AP18C8K,
- BATTERY_COSMX_AP20CBL,
- BATTERY_TYPE_COUNT,
-};
-
-enum pwm_channel {
- PWM_CH_FAN,
- PWM_CH_KBLIGHT,
- PWM_CH_COUNT
-};
-
-enum sensor_id {
- LID_ACCEL = 0,
- BASE_ACCEL,
- BASE_GYRO,
- SENSOR_COUNT,
-};
-
-enum usbc_port {
- USBC_PORT_C0 = 0,
- USBC_PORT_C1,
- USBC_PORT_COUNT
-};
-
-void board_reset_pd_mcu(void);
-
-void motion_interrupt(enum gpio_signal signal);
-
-#endif /* !__ASSEMBLER__ */
-
-#endif /* __CROS_EC_BOARD_H */
diff --git a/board/volet/build.mk b/board/volet/build.mk
deleted file mode 100644
index 546bcba8d2..0000000000
--- a/board/volet/build.mk
+++ /dev/null
@@ -1,17 +0,0 @@
-# -*- makefile -*-
-# Copyright 2021 The Chromium OS Authors. All rights reserved.
-# Use of this source code is governed by a BSD-style license that can be
-# found in the LICENSE file.
-#
-# Board specific files build
-#
-
-CHIP:=npcx
-CHIP_FAMILY:=npcx7
-CHIP_VARIANT:=npcx7m7fc
-BASEBOARD:=volteer
-
-board-y=board.o
-board-y+=battery.o
-board-y+=led.o
-board-y+=sensors.o
diff --git a/board/volet/ec.tasklist b/board/volet/ec.tasklist
deleted file mode 100644
index e76bd368eb..0000000000
--- a/board/volet/ec.tasklist
+++ /dev/null
@@ -1,26 +0,0 @@
-/* Copyright 2021 The Chromium OS Authors. All rights reserved.
- * Use of this source code is governed by a BSD-style license that can be
- * found in the LICENSE file.
- */
-
-/*
- * See CONFIG_TASK_LIST in config.h for details.
- */
-
-#define CONFIG_TASK_LIST \
- TASK_ALWAYS(HOOKS, hook_task, NULL, LARGER_TASK_STACK_SIZE) \
- TASK_ALWAYS(CHG_RAMP, chg_ramp_task, NULL, TASK_STACK_SIZE) \
- TASK_ALWAYS(USB_CHG_P0, usb_charger_task, 0, TASK_STACK_SIZE) \
- TASK_ALWAYS(USB_CHG_P1, usb_charger_task, 0, TASK_STACK_SIZE) \
- TASK_ALWAYS(CHARGER, charger_task, NULL, VENTI_TASK_STACK_SIZE) \
- TASK_ALWAYS(MOTIONSENSE, motion_sense_task, NULL, VENTI_TASK_STACK_SIZE) \
- TASK_NOTEST(KEYPROTO, keyboard_protocol_task, NULL, TASK_STACK_SIZE) \
- TASK_NOTEST(CHIPSET, chipset_task, NULL, LARGER_TASK_STACK_SIZE) \
- TASK_ALWAYS(HOSTCMD, host_command_task, NULL, LARGER_TASK_STACK_SIZE) \
- TASK_ALWAYS(CONSOLE, console_task, NULL, VENTI_TASK_STACK_SIZE) \
- TASK_ALWAYS(POWERBTN, power_button_task, NULL, LARGER_TASK_STACK_SIZE) \
- TASK_NOTEST(KEYSCAN, keyboard_scan_task, NULL, TASK_STACK_SIZE) \
- TASK_ALWAYS(PD_C0, pd_task, NULL, VENTI_TASK_STACK_SIZE) \
- TASK_ALWAYS(PD_C1, pd_task, NULL, VENTI_TASK_STACK_SIZE) \
- TASK_ALWAYS(PD_INT_C0, pd_interrupt_handler_task, 0, TASK_STACK_SIZE) \
- TASK_ALWAYS(PD_INT_C1, pd_interrupt_handler_task, 1, TASK_STACK_SIZE)
diff --git a/board/volet/gpio.inc b/board/volet/gpio.inc
deleted file mode 100644
index ed4b426a86..0000000000
--- a/board/volet/gpio.inc
+++ /dev/null
@@ -1,184 +0,0 @@
-/* -*- mode:c -*-
- *
- * Copyright 2021 The Chromium OS Authors. All rights reserved.
- * Use of this source code is governed by a BSD-style license that can be
- * found in the LICENSE file.
- */
-
-/* Declare symbolic names for all the GPIOs that we care about.
- * Note: Those with interrupt handlers must be declared first. */
-
-/* Wake Source interrupts */
-GPIO_INT(EC_LID_OPEN, PIN(D, 2), GPIO_INT_BOTH | GPIO_HIB_WAKE_HIGH, lid_interrupt)
-GPIO_INT(EC_WP_L, PIN(A, 1), GPIO_INT_BOTH, switch_interrupt)
-GPIO_INT(H1_EC_PWR_BTN_ODL, PIN(0, 1), GPIO_INT_BOTH, power_button_interrupt)
-GPIO_INT(ACOK_OD, PIN(0, 0), GPIO_INT_BOTH | GPIO_HIB_WAKE_HIGH, extpower_interrupt)
-
-/* Power sequencing interrupts */
-GPIO_INT(SLP_S0_L, PIN(D, 5), GPIO_INT_BOTH, power_signal_interrupt)
-#ifndef CONFIG_HOSTCMD_ESPI_VW_SLP_S3
-GPIO_INT(SLP_S3_L, PIN(A, 5), GPIO_INT_BOTH, power_signal_interrupt)
-#endif
-GPIO_INT(SLP_SUS_L, PIN(D, 7), GPIO_INT_BOTH, power_signal_interrupt)
-GPIO_INT(PG_EC_RSMRST_ODL, PIN(E, 2), GPIO_INT_BOTH, power_signal_interrupt)
-GPIO_INT(PG_EC_DSW_PWROK, PIN(C, 7), GPIO_INT_BOTH, power_signal_interrupt)
-GPIO_INT(PG_EC_ALL_SYS_PWRGD, PIN(F, 4), GPIO_INT_BOTH, power_signal_interrupt)
-
-/* Sensor Interrupts */
-GPIO_INT(EC_IMU_INT_L, PIN(5, 6), GPIO_INT_FALLING | GPIO_SEL_1P8V, motion_interrupt)
-GPIO(EC_ALS_RGB_INT_L, PIN(D, 4), GPIO_INPUT | GPIO_PULL_UP) /* unused */
-GPIO_INT(TABLET_MODE_L, PIN(9, 5), GPIO_INT_BOTH, gmr_tablet_switch_isr)
-/*
- * Lid g-sensor interrupt unused on Voxel, configure as regular input for
- * power saving.
- */
-GPIO(EC_ACCEL_INT, PIN(8, 1), GPIO_INPUT | GPIO_PULL_UP)
-
-/* USB-C interrupts */
-GPIO_INT(USB_C0_TCPC_INT_ODL, PIN(E, 0), GPIO_INT_BOTH, tcpc_alert_event)
-GPIO_INT(USB_C1_TCPC_INT_ODL, PIN(A, 2), GPIO_INT_BOTH, tcpc_alert_event)
-
-GPIO_INT(USB_C0_PPC_INT_ODL, PIN(6, 2), GPIO_INT_BOTH, ppc_interrupt)
-GPIO_INT(USB_C1_PPC_INT_ODL, PIN(F, 5), GPIO_INT_BOTH, ppc_interrupt)
-
-GPIO_INT(USB_C0_BC12_INT_ODL, PIN(E, 4), GPIO_INT_BOTH, bc12_interrupt)
-GPIO_INT(USB_C1_MIX_INT_ODL, PIN(0, 3), GPIO_INT_BOTH, bc12_interrupt)
-
-/* HDMI interrupts */
-
-/* Volume button interrupts */
-GPIO_INT(EC_VOLDN_BTN_ODL, PIN(9, 3), GPIO_INT_BOTH | GPIO_PULL_UP, button_interrupt)
-GPIO_INT(EC_VOLUP_BTN_ODL, PIN(9, 7), GPIO_INT_BOTH | GPIO_PULL_UP, button_interrupt)
-
-/* Power Sequencing Signals */
-GPIO(EN_PP3300_A, PIN(A, 3), GPIO_OUT_LOW)
-GPIO(EN_PP5000_A, PIN(A, 4), GPIO_OUT_LOW)
-GPIO(EN_PPVAR_VCCIN, PIN(4, 3), GPIO_OUT_LOW) /* Enables VCCIN IMPV9 */
-GPIO(EC_PCH_DSW_PWROK, PIN(C, 0), GPIO_OUT_LOW)
-
-/* Other wake sources */
-/*
- * GPIO_INT_BOTH is required for PSL wake from hibernate, but we don't need an
- * interrupt handler because it is automatically handled by the PSL.
- *
- * We need to lock the setting so this gpio can't be reconfigured to overdrive
- * the real reset signal. (This is the PSL input pin not the real reset pin).
- */
-GPIO(EC_RST_ODL, PIN(0, 2), GPIO_INT_BOTH |
- GPIO_HIB_WAKE_HIGH |
- GPIO_LOCKED)
-
-/* AP/PCH Signals */
-GPIO(EC_PCH_SYS_PWROK, PIN(3, 7), GPIO_OUT_LOW)
-GPIO(EC_PCH_RSMRST_ODL, PIN(A, 6), GPIO_ODR_LOW) /* TODO - b/140950085 - implement TGL sequencing requirement */
-GPIO(EC_PCH_PWR_BTN_ODL, PIN(C, 1), GPIO_ODR_HIGH)
-GPIO(EC_PCH_RTCRST, PIN(7, 6), GPIO_OUT_LOW)
-GPIO(EC_PCH_WAKE_ODL, PIN(7, 4), GPIO_ODR_HIGH)
-GPIO(EC_ENTERING_RW, PIN(E, 3), GPIO_OUT_LOW)
-GPIO(EC_PROCHOT_ODL, PIN(6, 3), GPIO_ODR_HIGH)
-GPIO_INT(EC_PROCHOT_IN_L, PIN(F, 0), GPIO_INT_BOTH, throttle_ap_prochot_input_interrupt)
-GPIO(SYS_RST_ODL, PIN(C, 5), GPIO_ODR_HIGH)
-
-GPIO(EC_PCH_INT_ODL, PIN(B, 0), GPIO_ODR_HIGH)
-GPIO(CPU_C10_GATE_L, PIN(6, 7), GPIO_INPUT)
-
-/* USB and USBC Signals */
-GPIO(EN_PP5000_USBA, PIN(3, 5), GPIO_OUT_LOW) /* Enable USB-A charging - all ports */
-GPIO(USB_A_LOW_PWR_OD, PIN(6, 6), GPIO_ODR_LOW) /* Don't limit USB-A charging by default - all ports */
-
-/*
- * USB_C1 moved from GPIO32 to GPIO83 on boards with board ID >=1.
- * GPIO83/EN_PP1800_A is DNS on board ID 0 and GPIO32 is N/C on board ID >=1
- * so it's safe to define GPIOs compatible with both designs.
- * TODO (b/149858568): remove board ID=0 support.
- */
-GPIO(USB_C0_RT_RST_ODL, PIN(4, 1), GPIO_ODR_LOW)
-GPIO(USB_C1_RT_RST_ODL, PIN(8, 3), GPIO_ODR_LOW) /* USB_C1 Reset on boards board ID >=1 */
-GPIO(USB_C0_OC_ODL, PIN(B, 1), GPIO_ODR_HIGH)
-GPIO(USB_C1_OC_ODL, PIN(5, 0), GPIO_ODR_HIGH)
-GPIO(USB_C0_RT_INT_ODL, PIN(C, 6), GPIO_INPUT)
-GPIO(USB_C1_RT_INT_ODL, PIN(9, 6), GPIO_INPUT)
-GPIO(USB_C0_FRS_EN, PIN(C, 2), GPIO_OUT_LOW)
-GPIO(USB_C1_FRS_EN, PIN(9, 4), GPIO_OUT_LOW)
-
-/* Don't have a load switch for retimer */
-UNIMPLEMENTED(USB_C0_LS_EN)
-UNIMPLEMENTED(USB_C1_LS_EN)
-
-/* Misc Signals */
-GPIO(EC_H1_PACKET_MODE, PIN(7, 5), GPIO_OUT_LOW) /* H1 Packet Mode */
-GPIO(LED_1_L, PIN(C, 4), GPIO_OUT_HIGH) /* Blue */
-GPIO(LED_2_L, PIN(C, 3), GPIO_OUT_HIGH) /* Yellow */
-GPIO(EC_KB_BL_EN, PIN(8, 6), GPIO_OUT_LOW) /* Keyboard backlight enable*/
-
-GPIO(M2_SSD_PLN, PIN(A, 0), GPIO_ODR_HIGH) /* SSD power-loss notification */
-GPIO(M2_SSD_PLA, PIN(7, 0), GPIO_INPUT) /* SSD power-loss acknowledgment */
-GPIO(CCD_MODE_ODL, PIN(E, 5), GPIO_INPUT) /* Case Closed Debug Mode */
-GPIO(EC_SLP_S0IX, PIN(7, 2), GPIO_INPUT | GPIO_PULL_UP)
-
-/* Unused signals */
-GPIO(UNUSED_GPIO34, PIN(3, 4), GPIO_INPUT | GPIO_PULL_UP)
-GPIO(UNUSED_GPIO60, PIN(6, 0), GPIO_INPUT | GPIO_PULL_UP)
-GPIO(UNUSED_GPIOA7, PIN(A, 7), GPIO_INPUT | GPIO_PULL_UP)
-GPIO(UNUSED_GPIOD0, PIN(D, 0), GPIO_INPUT | GPIO_PULL_UP)
-GPIO(UNUSED_GPIOD1, PIN(D, 1), GPIO_INPUT | GPIO_PULL_UP)
-GPIO(UNUSED_GPIOF2, PIN(F, 2), GPIO_INPUT | GPIO_PULL_UP)
-GPIO(UNUSED_GPIOF3, PIN(F, 3), GPIO_INPUT | GPIO_PULL_UP)
-
-/*
- * eDP backlight - both PCH and EC have enable pins that must be high
- * for the backlight to turn on. Default state is high, and can be turned
- * off during sleep states.
- */
-GPIO(EC_EDP_BL_EN, PIN(D, 3), GPIO_OUT_HIGH)
-
-/* I2C pins - Alternate function below configures I2C module on these pins */
-GPIO(EC_I2C0_SENSOR_SCL, PIN(B, 5), GPIO_INPUT | GPIO_SEL_1P8V)
-GPIO(EC_I2C0_SENSOR_SDA, PIN(B, 4), GPIO_INPUT | GPIO_SEL_1P8V)
-GPIO(EC_I2C1_USB_C0_SCL, PIN(9, 0), GPIO_INPUT)
-GPIO(EC_I2C1_USB_C0_SDA, PIN(8, 7), GPIO_INPUT)
-GPIO(EC_I2C2_USB_C1_SCL, PIN(9, 2), GPIO_INPUT)
-GPIO(EC_I2C2_USB_C1_SDA, PIN(9, 1), GPIO_INPUT)
-GPIO(EC_I2C5_POWER_SCL, PIN(3, 3), GPIO_INPUT)
-GPIO(EC_I2C5_POWER_SDA, PIN(3, 6), GPIO_INPUT)
-GPIO(EC_I2C7_EEPROM_SCL, PIN(B, 3), GPIO_INPUT)
-GPIO(EC_I2C7_EEPROM_SDA, PIN(B, 2), GPIO_INPUT)
-
-/* Battery signals */
-GPIO(EC_BATT_PRES_ODL, PIN(E, 1), GPIO_INPUT)
-
-/* Alternate functions GPIO definitions */
-ALTERNATE(PIN_MASK(B, BIT(5) | BIT(4)), 0, MODULE_I2C, (GPIO_INPUT | GPIO_SEL_1P8V)) /* I2C0 */
-ALTERNATE(PIN_MASK(9, BIT(0) | BIT(2) | BIT(1)), 0, MODULE_I2C, 0) /* I2C1 SCL / I2C2 */
-ALTERNATE(PIN_MASK(8, BIT(7)), 0, MODULE_I2C, 0) /* I2C1 SDA */
-ALTERNATE(PIN_MASK(3, BIT(3) | BIT(6)), 0, MODULE_I2C, 0) /* I2C5 */
-ALTERNATE(PIN_MASK(B, BIT(3) | BIT(2)), 0, MODULE_I2C, 0) /* I2C7 */
-
-/* Fan signals */
-GPIO(EN_PP5000_FAN, PIN(6, 1), GPIO_OUT_LOW)
-ALTERNATE(PIN_MASK(B, BIT(7)), 0, MODULE_PWM, 0) /* FAN_PWM */
-ALTERNATE(PIN_MASK(4, BIT(0)), 0, MODULE_PWM, 0) /* FAN_SPEED_TACH */
-
-/* Keyboard pins */
-#define GPIO_KB_INPUT (GPIO_INPUT | GPIO_PULL_UP)
-ALTERNATE(PIN_MASK(3, 0x03), 0, MODULE_KEYBOARD_SCAN, GPIO_KB_INPUT) /* KSI_00-01 */
-ALTERNATE(PIN_MASK(2, 0xFC), 0, MODULE_KEYBOARD_SCAN, GPIO_KB_INPUT) /* KSI_02-07 */
-ALTERNATE(PIN_MASK(2, 0x03), 0, MODULE_KEYBOARD_SCAN, GPIO_ODR_HIGH) /* KSO_00-01 */
-GPIO(EC_KSO_02_INV, PIN(1, 7), GPIO_OUT_LOW) /* KSO_02 */
-ALTERNATE(PIN_MASK(1, 0x7F), 0, MODULE_KEYBOARD_SCAN, GPIO_ODR_HIGH) /* KSO_03-09 */
-ALTERNATE(PIN_MASK(0, 0xF0), 0, MODULE_KEYBOARD_SCAN, GPIO_ODR_HIGH) /* KSO_10-13 */
-ALTERNATE(PIN_MASK(8, 0x04), 0, MODULE_KEYBOARD_SCAN, GPIO_ODR_HIGH) /* KSO_14 */
-ALTERNATE(PIN_MASK(8, BIT(0)), 0, MODULE_PWM, 0) /* EC_KB_BL_PWM */
-
-/* UART */
-ALTERNATE(PIN_MASK(6, BIT(5) | BIT(4)), 0, MODULE_UART, 0) /* UART from EC to Servo */
-
-/* Power Switch Logic (PSL) inputs */
-ALTERNATE(PIN_MASK(D, BIT(2)), 0, MODULE_PMU, 0) /* GPIOD2 = EC_LID_OPEN */
-ALTERNATE(PIN_MASK(0, BIT(0) | BIT(1) | BIT(2)), 0, MODULE_PMU, 0) /* GPIO00 = ACOK_OD,
- GPIO01 = H1_EC_PWR_BTN_ODL
- GPIO02 = EC_RST_ODL */
-
-/* Temperature sensors */
-ALTERNATE(PIN_MASK(4, BIT(2) | BIT(4) | BIT(5)), 0, MODULE_ADC, 0) /* TEMP_SENSOR1,2,4 */
-ALTERNATE(PIN(F, 1), 0, MODULE_ADC, 0) /* TEMP_SENSOR3 */
diff --git a/board/volet/led.c b/board/volet/led.c
deleted file mode 100644
index ba4af36163..0000000000
--- a/board/volet/led.c
+++ /dev/null
@@ -1,79 +0,0 @@
-/* Copyright 2021 The Chromium OS Authors. All rights reserved.
- * Use of this source code is governed by a BSD-style license that can be
- * found in the LICENSE file.
- *
- * Power and battery LED control for Volteer
- */
-
-#include "ec_commands.h"
-#include "gpio.h"
-#include "led_common.h"
-#include "led_onoff_states.h"
-#include "chipset.h"
-
-#define LED_ON_LVL 0
-#define LED_OFF_LVL 1
-
-__override const int led_charge_lvl_1 = 5;
-
-__override const int led_charge_lvl_2 = 95;
-
-__override struct led_descriptor
- led_bat_state_table[LED_NUM_STATES][LED_NUM_PHASES] = {
- [STATE_CHARGING_LVL_1] = {{EC_LED_COLOR_AMBER, LED_INDEFINITE} },
- [STATE_CHARGING_LVL_2] = {{EC_LED_COLOR_AMBER, LED_INDEFINITE} },
- [STATE_CHARGING_FULL_CHARGE] = {{EC_LED_COLOR_BLUE, LED_INDEFINITE} },
- [STATE_DISCHARGE_S0] = {{EC_LED_COLOR_BLUE, LED_INDEFINITE} },
- [STATE_DISCHARGE_S3] = {{EC_LED_COLOR_AMBER, 1 * LED_ONE_SEC},
- {LED_OFF, 3 * LED_ONE_SEC} },
- [STATE_DISCHARGE_S5] = {{LED_OFF, LED_INDEFINITE} },
- [STATE_BATTERY_ERROR] = {{EC_LED_COLOR_AMBER, 1 * LED_ONE_SEC},
- {LED_OFF, 1 * LED_ONE_SEC} },
- [STATE_FACTORY_TEST] = {{EC_LED_COLOR_BLUE, 2 * LED_ONE_SEC},
- {EC_LED_COLOR_AMBER, 2 * LED_ONE_SEC} },
-};
-
-const enum ec_led_id supported_led_ids[] = {
- EC_LED_ID_BATTERY_LED
-};
-
-const int supported_led_ids_count = ARRAY_SIZE(supported_led_ids);
-
-__override void led_set_color_battery(enum ec_led_colors color)
-{
- switch (color) {
- case EC_LED_COLOR_AMBER:
- gpio_set_level(GPIO_LED_2_L, LED_ON_LVL);
- gpio_set_level(GPIO_LED_1_L, LED_OFF_LVL);
- break;
- case EC_LED_COLOR_BLUE:
- gpio_set_level(GPIO_LED_1_L, LED_ON_LVL);
- gpio_set_level(GPIO_LED_2_L, LED_OFF_LVL);
- break;
- default: /* LED_OFF and other unsupported colors */
- gpio_set_level(GPIO_LED_1_L, LED_OFF_LVL);
- gpio_set_level(GPIO_LED_2_L, LED_OFF_LVL);
- break;
- }
-}
-
-void led_get_brightness_range(enum ec_led_id led_id, uint8_t *brightness_range)
-{
- if (led_id == EC_LED_ID_BATTERY_LED) {
- brightness_range[EC_LED_COLOR_AMBER] = 1;
- brightness_range[EC_LED_COLOR_BLUE] = 1;
- }
-}
-
-int led_set_brightness(enum ec_led_id led_id, const uint8_t *brightness)
-{
- if (led_id == EC_LED_ID_BATTERY_LED) {
- if (brightness[EC_LED_COLOR_BLUE] != 0)
- led_set_color_battery(EC_LED_COLOR_BLUE);
- else if (brightness[EC_LED_COLOR_AMBER] != 0)
- led_set_color_battery(EC_LED_COLOR_AMBER);
- else
- led_set_color_battery(LED_OFF);
- }
- return EC_SUCCESS;
-}
diff --git a/board/volet/sensors.c b/board/volet/sensors.c
deleted file mode 100644
index 49e879ea94..0000000000
--- a/board/volet/sensors.c
+++ /dev/null
@@ -1,247 +0,0 @@
-/* Copyright 2021 The Chromium OS Authors. All rights reserved.
- * Use of this source code is governed by a BSD-style license that can be
- * found in the LICENSE file.
- */
-
-/* Volteer family-specific sensor configuration */
-#include "common.h"
-#include "accelgyro.h"
-#include "cbi_ec_fw_config.h"
-#include "cbi_ssfc.h"
-#include "driver/accel_bma2x2.h"
-#include "driver/accel_kionix.h"
-#include "driver/accelgyro_bmi_common.h"
-#include "driver/accelgyro_bmi160.h"
-#include "driver/accelgyro_icm_common.h"
-#include "driver/accelgyro_icm426xx.h"
-#include "driver/als_tcs3400.h"
-#include "driver/sync.h"
-#include "keyboard_scan.h"
-#include "hooks.h"
-#include "i2c.h"
-#include "task.h"
-#include "tablet_mode.h"
-#include "util.h"
-
-#define CPRINTS(format, args...) cprints(CC_MOTION_SENSE, format, ## args)
-/******************************************************************************/
-/* Sensors */
-static struct mutex g_lid_accel_mutex;
-static struct mutex g_base_mutex;
-
-/* BMA253 private data */
-static struct accelgyro_saved_data_t g_bma253_data;
-static struct kionix_accel_data g_kx022_data;
-
-/* BMI160 private data */
-static struct bmi_drv_data_t g_bmi160_data;
-static struct icm_drv_data_t g_icm426xx_data;
-
-/* Rotation matrix for the lid accelerometer */
-static const mat33_fp_t lid_standard_ref = {
- { FLOAT_TO_FP(-1), 0, 0},
- { 0, FLOAT_TO_FP(-1), 0},
- { 0, 0, FLOAT_TO_FP(1)}
-};
-
-const mat33_fp_t base_standard_ref = {
- { 0, FLOAT_TO_FP(1), 0},
- { FLOAT_TO_FP(-1), 0, 0},
- { 0, 0, FLOAT_TO_FP(1)}
-};
-
-static const mat33_fp_t base_icm_ref = {
- { FLOAT_TO_FP(1), 0, 0},
- { 0, FLOAT_TO_FP(1), 0},
- { 0, 0, FLOAT_TO_FP(1)}
-};
-
-struct motion_sensor_t kx022_lid_accel = {
- .name = "Lid Accel",
- .active_mask = SENSOR_ACTIVE_S0_S3,
- .chip = MOTIONSENSE_CHIP_KX022,
- .type = MOTIONSENSE_TYPE_ACCEL,
- .location = MOTIONSENSE_LOC_LID,
- .drv = &kionix_accel_drv,
- .mutex = &g_lid_accel_mutex,
- .drv_data = &g_kx022_data,
- .port = I2C_PORT_ACCEL,
- .i2c_spi_addr_flags = KX022_ADDR0_FLAGS,
- .rot_standard_ref = &lid_standard_ref,
- .min_frequency = KX022_ACCEL_MIN_FREQ,
- .max_frequency = KX022_ACCEL_MAX_FREQ,
- .default_range = 2, /* g, to support tablet mode */
- .config = {
- /* EC use accel for angle detection */
- [SENSOR_CONFIG_EC_S0] = {
- .odr = 10000 | ROUND_UP_FLAG,
- },
- /* EC use accel for angle detection */
- [SENSOR_CONFIG_EC_S3] = {
- .odr = 10000 | ROUND_UP_FLAG,
- },
- },
-};
-
-struct motion_sensor_t icm426xx_base_accel = {
- .name = "Base Accel",
- .active_mask = SENSOR_ACTIVE_S0_S3,
- .chip = MOTIONSENSE_CHIP_ICM426XX,
- .type = MOTIONSENSE_TYPE_ACCEL,
- .location = MOTIONSENSE_LOC_BASE,
- .drv = &icm426xx_drv,
- .mutex = &g_base_mutex,
- .drv_data = &g_icm426xx_data,
- .port = I2C_PORT_ACCEL,
- .i2c_spi_addr_flags = ICM426XX_ADDR0_FLAGS,
- .default_range = 4, /* g, to meet CDD 7.3.1/C-1-4 reqs.*/
- .rot_standard_ref = &base_icm_ref,
- .min_frequency = ICM426XX_ACCEL_MIN_FREQ,
- .max_frequency = ICM426XX_ACCEL_MAX_FREQ,
- .config = {
- /* EC use accel for angle detection */
- [SENSOR_CONFIG_EC_S0] = {
- .odr = 10000 | ROUND_UP_FLAG,
- .ec_rate = 100 * MSEC,
- },
- /* EC use accel for angle detection */
- [SENSOR_CONFIG_EC_S3] = {
- .odr = 10000 | ROUND_UP_FLAG,
- .ec_rate = 100 * MSEC,
- },
- },
-};
-
-struct motion_sensor_t icm426xx_base_gyro = {
- .name = "Base Gyro",
- .active_mask = SENSOR_ACTIVE_S0_S3,
- .chip = MOTIONSENSE_CHIP_ICM426XX,
- .type = MOTIONSENSE_TYPE_GYRO,
- .location = MOTIONSENSE_LOC_BASE,
- .drv = &icm426xx_drv,
- .mutex = &g_base_mutex,
- .drv_data = &g_icm426xx_data,
- .port = I2C_PORT_ACCEL,
- .i2c_spi_addr_flags = ICM426XX_ADDR0_FLAGS,
- .default_range = 1000, /* dps */
- .rot_standard_ref = &base_icm_ref,
- .min_frequency = ICM426XX_GYRO_MIN_FREQ,
- .max_frequency = ICM426XX_GYRO_MAX_FREQ,
-};
-
-struct motion_sensor_t motion_sensors[] = {
- [LID_ACCEL] = {
- .name = "Lid Accel",
- .active_mask = SENSOR_ACTIVE_S0_S3,
- .chip = MOTIONSENSE_CHIP_BMA255,
- .type = MOTIONSENSE_TYPE_ACCEL,
- .location = MOTIONSENSE_LOC_LID,
- .drv = &bma2x2_accel_drv,
- .mutex = &g_lid_accel_mutex,
- .drv_data = &g_bma253_data,
- .port = I2C_PORT_SENSOR,
- .i2c_spi_addr_flags = BMA2x2_I2C_ADDR1_FLAGS,
- .rot_standard_ref = &lid_standard_ref,
- .min_frequency = BMA255_ACCEL_MIN_FREQ,
- .max_frequency = BMA255_ACCEL_MAX_FREQ,
- .default_range = 2, /* g, to support tablet mode */
- .config = {
- /* EC use accel for angle detection */
- [SENSOR_CONFIG_EC_S0] = {
- .odr = 10000 | ROUND_UP_FLAG,
- },
- /* Sensor on in S3 */
- [SENSOR_CONFIG_EC_S3] = {
- .odr = 10000 | ROUND_UP_FLAG,
- },
- },
- },
- [BASE_ACCEL] = {
- .name = "Base Accel",
- .active_mask = SENSOR_ACTIVE_S0_S3,
- .chip = MOTIONSENSE_CHIP_BMI160,
- .type = MOTIONSENSE_TYPE_ACCEL,
- .location = MOTIONSENSE_LOC_BASE,
- .drv = &bmi160_drv,
- .mutex = &g_base_mutex,
- .drv_data = &g_bmi160_data,
- .port = I2C_PORT_SENSOR,
- .i2c_spi_addr_flags = BMI160_ADDR0_FLAGS,
- .rot_standard_ref = &base_standard_ref,
- .min_frequency = BMI_ACCEL_MIN_FREQ,
- .max_frequency = BMI_ACCEL_MAX_FREQ,
- .default_range = 4, /* g */
- .config = {
- /* EC use accel for angle detection */
- [SENSOR_CONFIG_EC_S0] = {
- .odr = 10000 | ROUND_UP_FLAG,
- .ec_rate = 100 * MSEC,
- },
- /* Sensor on in S3 */
- [SENSOR_CONFIG_EC_S3] = {
- .odr = 10000 | ROUND_UP_FLAG,
- .ec_rate = 100 * MSEC,
- },
- },
- },
-
- [BASE_GYRO] = {
- .name = "Base Gyro",
- .active_mask = SENSOR_ACTIVE_S0_S3,
- .chip = MOTIONSENSE_CHIP_BMI160,
- .type = MOTIONSENSE_TYPE_GYRO,
- .location = MOTIONSENSE_LOC_BASE,
- .drv = &bmi160_drv,
- .mutex = &g_base_mutex,
- .drv_data = &g_bmi160_data,
- .port = I2C_PORT_SENSOR,
- .i2c_spi_addr_flags = BMI160_ADDR0_FLAGS,
- .default_range = 1000, /* dps */
- .rot_standard_ref = &base_standard_ref,
- .min_frequency = BMI_GYRO_MIN_FREQ,
- .max_frequency = BMI_GYRO_MAX_FREQ,
- },
-};
-unsigned int motion_sensor_count = ARRAY_SIZE(motion_sensors);
-
-static void board_sensors_init(void)
-{
- if (ec_cfg_has_tabletmode()) {
- if (get_cbi_ssfc_base_sensor() == SSFC_SENSOR_BASE_ICM426XX) {
- motion_sensors[BASE_ACCEL] = icm426xx_base_accel;
- motion_sensors[BASE_GYRO] = icm426xx_base_gyro;
- ccprints("BASE GYRO is ICM426XX");
- } else
- ccprints("BASE GYRO is BMI160");
-
- if (get_cbi_ssfc_lid_sensor() == SSFC_SENSOR_LID_KX022) {
- motion_sensors[LID_ACCEL] = kx022_lid_accel;
- ccprints("LID_ACCEL is KX022");
- } else
- ccprints("LID_ACCEL is BMA253");
-
- motion_sensor_count = ARRAY_SIZE(motion_sensors);
- /* Enable interrupt for the accel/gyro sensor */
- gpio_enable_interrupt(GPIO_EC_IMU_INT_L);
- } else {
- motion_sensor_count = 0;
- gmr_tablet_switch_disable();
- /* Base accel is not stuffed, don't allow line to float */
- gpio_set_flags(GPIO_EC_IMU_INT_L,
- GPIO_INPUT | GPIO_PULL_DOWN);
- }
-}
-DECLARE_HOOK(HOOK_INIT, board_sensors_init, HOOK_PRIO_DEFAULT);
-
-void motion_interrupt(enum gpio_signal signal)
-{
- switch (get_cbi_ssfc_base_sensor()) {
- case SSFC_SENSOR_BASE_ICM426XX:
- icm426xx_interrupt(signal);
- break;
- case SSFC_SENSOR_BASE_BMI160:
- default:
- bmi160_interrupt(signal);
- break;
- }
-}
diff --git a/board/volet/vif_override.xml b/board/volet/vif_override.xml
deleted file mode 100644
index 3fc41630da..0000000000
--- a/board/volet/vif_override.xml
+++ /dev/null
@@ -1,158 +0,0 @@
-<?xml version="1.0" encoding="utf-8"?>
-<VIF xmlns="http://usb.org/VendorInfoFile.xsd">
- <Model_Part_Number>Voxel</Model_Part_Number>
- <Product_Revision>0</Product_Revision>
- <TID>0</TID>
- <Product>
- <!-- Information about TGL USB4 provided by Intel. See b/172963736 -->
- <USB4_Num_Internal_Host_Controllers value="1" />
- <USB4_Num_PCIe_DN_Bridges value="0" />
- <USB4RouterList>
- <Usb4Router>
- <USB4_Router_ID value="1" />
- <USB4_Silicon_VID value="32903">8087</USB4_Silicon_VID>
- <USB4_Num_Lane_Adapters value="4" />
- <USB4_Num_USB3_DN_Adapters value="1" />
- <USB4_Num_DP_IN_Adapters value="1" />
- <USB4_Num_DP_OUT_Adapters value="0" />
- <USB4_Num_PCIe_DN_Adapters value="4" />
- <USB4_TBT3_Not_Supported value="0">TBT3 Compatible</USB4_TBT3_Not_Supported>
- <USB4_PCIe_Wake_Supported value="true" />
- <USB4_USB3_Wake_Supported value="false" />
- <USB4_Num_Unused_Adapters value="0" />
- <USB4_TBT3_VID value="32903">8087</USB4_TBT3_VID>
- <USB4_PCIe_Switch_Vendor_ID value="32902">8086</USB4_PCIe_Switch_Vendor_ID>
- <USB4_PCIe_Switch_Device_ID value="39451">9A1B</USB4_PCIe_Switch_Device_ID>
- </Usb4Router>
- <Usb4Router>
- <USB4_Router_ID value="0" />
- <USB4_Silicon_VID value="32903">8087</USB4_Silicon_VID>
- <USB4_Num_Lane_Adapters value="2" />
- <USB4_Num_USB3_DN_Adapters value="1" />
- <USB4_Num_DP_IN_Adapters value="0" />
- <USB4_Num_DP_OUT_Adapters value="0" />
- <USB4_Num_PCIe_DN_Adapters value="0" />
- <USB4_TBT3_Not_Supported value="1">Not TBT3-Compatible</USB4_TBT3_Not_Supported>
- <USB4_PCIe_Wake_Supported value="false" />
- <USB4_USB3_Wake_Supported value="false" />
- <USB4_Num_Unused_Adapters value="0" />
- </Usb4Router>
- </USB4RouterList>
- </Product>
- <Component>
- <USB4_Max_Speed value="1">Gen 3 (40Gb)</USB4_Max_Speed>
- <USB4_DFP_Supported value="true" />
- <USB4_UFP_Supported value="false" />
- <USB4_USB3_Tunneling_Supported value="true" />
- <USB4_DP_Tunneling_Supported value="true" />
- <USB4_PCIe_Tunneling_Supported value="true" />
- <USB4_TBT3_Compatibility_Supported value="true" />
- <USB4_CL1_State_Supported value="true" />
- <USB4_CL2_State_Supported value="true" />
- <USB4_Num_Retimers value="1" />
- <USB4_DP_Bit_Rate value="3">HBR3</USB4_DP_Bit_Rate>
- <USB4_Num_DP_Lanes value="4">4 Lanes</USB4_Num_DP_Lanes>
- <USB4_Lane_0_Adapter value="1" />
- <Host_Supports_USB_Data value="true" />
- <Host_Speed value="2">USB 3.2 Gen 2x1</Host_Speed>
- <Host_Contains_Captive_Retimer value="true" />
- <Host_Truncates_DP_For_tDHPResponse value="false" />
- <Host_Suspend_Supported value="true" />
- <Is_DFP_On_Hub value="false" />
- <USB_Suspend_May_Be_Cleared value="true" />
- <FR_Swap_Type_C_Current_Capability_As_Initial_Sink value="3">3A @ 5V</FR_Swap_Type_C_Current_Capability_As_Initial_Sink>
- <FR_Swap_Supported_As_Initial_Sink value="true" />
- <SrcPdoList>
- <SrcPDO>
- <!-- Add in missing fields for SrcPdo0, derived from SYV682B datasheet. -->
- <Src_PD_OCP_OC_Debounce value="50">50 msec</Src_PD_OCP_OC_Debounce>
- <Src_PD_OCP_OC_Threshold value="360">3600 mA</Src_PD_OCP_OC_Threshold>
- </SrcPDO>
- </SrcPdoList>
- <Data_Capable_As_USB_Host_SOP value="true" />
- <Data_Capable_As_USB_Device_SOP value="false" />
- <!-- TODO(b/173028252): Figure out the appropriate Discover Identity ACK for
- Volteer and update the EC and VIF accordingly. -->
- <Product_Type_UFP_SOP value="3">PSD</Product_Type_UFP_SOP>
- <Product_Type_DFP_SOP value="4">Alternate Mode Controller (AMC)</Product_Type_DFP_SOP>
- <DFP_VDO_Port_Number value="0" />
- <Modal_Operation_Supported_SOP value="true" />
- <USB_VID_SOP value="6353">18D1</USB_VID_SOP>
- <bcdDevice_SOP value="0">0000</bcdDevice_SOP>
- <SVID_Fixed_SOP value="true" />
- <Num_SVIDs_Min_SOP value="1" />
- <Num_SVIDs_Max_SOP value="1" />
- <SOPSVIDList>
- <SOPSVID>
- <SVID_SOP value="32903">8087</SVID_SOP>
- <SVID_Modes_Fixed_SOP value="true" />
- <SVID_Num_Modes_Min_SOP value="1" />
- <SVID_Num_Modes_Max_SOP value="1" />
- <SOPSVIDModeList>
- <SOPSVIDMode>
- <SVID_Mode_Enter_SOP value="true" />
- <SVID_Mode_Recog_Value_SOP value="0">00000000</SVID_Mode_Recog_Value_SOP>
- </SOPSVIDMode>
- </SOPSVIDModeList>
- </SOPSVID>
- </SOPSVIDList>
- </Component>
- <Component>
- <USB4_Max_Speed value="1">Gen 3 (40Gb)</USB4_Max_Speed>
- <USB4_DFP_Supported value="true" />
- <USB4_UFP_Supported value="false" />
- <USB4_USB3_Tunneling_Supported value="true" />
- <USB4_DP_Tunneling_Supported value="true" />
- <USB4_PCIe_Tunneling_Supported value="true" />
- <USB4_TBT3_Compatibility_Supported value="true" />
- <USB4_CL1_State_Supported value="true" />
- <USB4_CL2_State_Supported value="true" />
- <USB4_Num_Retimers value="1" />
- <USB4_DP_Bit_Rate value="3">HBR3</USB4_DP_Bit_Rate>
- <USB4_Num_DP_Lanes value="4">4 Lanes</USB4_Num_DP_Lanes>
- <USB4_Lane_0_Adapter value="1" />
- <Host_Supports_USB_Data value="true" />
- <Host_Speed value="2">USB 3.2 Gen 2x1</Host_Speed>
- <Host_Contains_Captive_Retimer value="true" />
- <Host_Truncates_DP_For_tDHPResponse value="false" />
- <Host_Suspend_Supported value="true" />
- <Is_DFP_On_Hub value="false" />
- <USB_Suspend_May_Be_Cleared value="true" />
- <FR_Swap_Type_C_Current_Capability_As_Initial_Sink value="3">3A @ 5V</FR_Swap_Type_C_Current_Capability_As_Initial_Sink>
- <FR_Swap_Supported_As_Initial_Sink value="true" />
- <SrcPdoList>
- <SrcPDO>
- <!-- Add in missing fields for SrcPdo0, derived from SYV682B datasheet. -->
- <Src_PD_OCP_OC_Debounce value="50">50 msec</Src_PD_OCP_OC_Debounce>
- <Src_PD_OCP_OC_Threshold value="360">3600 mA</Src_PD_OCP_OC_Threshold>
- </SrcPDO>
- </SrcPdoList>
- <Data_Capable_As_USB_Host_SOP value="true" />
- <Data_Capable_As_USB_Device_SOP value="false" />
- <!-- TODO(b/173028252): Figure out the appropriate Discover Identity ACK for
- Volteer and update the EC and VIF accordingly. -->
- <Product_Type_UFP_SOP value="3">PSD</Product_Type_UFP_SOP>
- <Product_Type_DFP_SOP value="4">Alternate Mode Controller (AMC)</Product_Type_DFP_SOP>
- <DFP_VDO_Port_Number value="1" />
- <Modal_Operation_Supported_SOP value="true" />
- <USB_VID_SOP value="6353">18D1</USB_VID_SOP>
- <bcdDevice_SOP value="0">0000</bcdDevice_SOP>
- <SVID_Fixed_SOP value="true" />
- <Num_SVIDs_Min_SOP value="1" />
- <Num_SVIDs_Max_SOP value="1" />
- <SOPSVIDList>
- <SOPSVID>
- <SVID_SOP value="32903">8087</SVID_SOP>
- <SVID_Modes_Fixed_SOP value="true" />
- <SVID_Num_Modes_Min_SOP value="1" />
- <SVID_Num_Modes_Max_SOP value="1" />
- <SOPSVIDModeList>
- <SOPSVIDMode>
- <SVID_Mode_Enter_SOP value="true" />
- <SVID_Mode_Recog_Value_SOP value="0">00000000</SVID_Mode_Recog_Value_SOP>
- </SOPSVIDMode>
- </SOPSVIDModeList>
- </SOPSVID>
- </SOPSVIDList>
- </Component>
-</VIF>
View Lorry Controller Status