diff options
Diffstat (limited to 'board/volmar/board.h')
| -rw-r--r-- | board/volmar/board.h | 286 |
1 files changed, 286 insertions, 0 deletions
diff --git a/board/volmar/board.h b/board/volmar/board.h new file mode 100644 index 0000000000..b9217e32d9 --- /dev/null +++ b/board/volmar/board.h @@ -0,0 +1,286 @@ +/* Copyright 2022 The Chromium OS Authors. All rights reserved. + * Use of this source code is governed by a BSD-style license that can be + * found in the LICENSE file. + */ + +/* Brya board configuration */ + +#ifndef __CROS_EC_BOARD_H +#define __CROS_EC_BOARD_H + +#include "compile_time_macros.h" + +/* + * Early brya boards are not set up for vivaldi + */ +#undef CONFIG_KEYBOARD_VIVALDI + +/* Baseboard features */ +#include "baseboard.h" + +/* + * This will happen automatically on NPCX9 ES2 and later. Do not remove + * until we can confirm all earlier chips are out of service. + */ +#define CONFIG_HIBERNATE_PSL_VCC1_RST_WAKEUP + +#define CONFIG_MP2964 + +/* LED */ +#define CONFIG_LED_PWM +#define CONFIG_LED_PWM_COUNT 2 +#undef CONFIG_LED_PWM_NEAR_FULL_COLOR +#undef CONFIG_LED_PWM_SOC_ON_COLOR +#undef CONFIG_LED_PWM_SOC_SUSPEND_COLOR +#undef CONFIG_LED_PWM_LOW_BATT_COLOR +#define CONFIG_LED_PWM_NEAR_FULL_COLOR EC_LED_COLOR_WHITE +#define CONFIG_LED_PWM_SOC_ON_COLOR EC_LED_COLOR_WHITE +#define CONFIG_LED_PWM_SOC_SUSPEND_COLOR EC_LED_COLOR_WHITE +#define CONFIG_LED_PWM_LOW_BATT_COLOR EC_LED_COLOR_AMBER + +/* Sensors */ +#define CONFIG_ACCELGYRO_LSM6DSO /* Base accel */ +#define CONFIG_ACCEL_LSM6DSO_INT_EVENT \ + TASK_EVENT_MOTION_SENSOR_INTERRUPT(BASE_ACCEL) + +/* TCS3400 ALS */ +#define CONFIG_ALS +#define ALS_COUNT 1 +#define CONFIG_ALS_TCS3400 +#define CONFIG_ALS_TCS3400_INT_EVENT \ + TASK_EVENT_MOTION_SENSOR_INTERRUPT(CLEAR_ALS) + +/* Enable sensor fifo, must also define the _SIZE and _THRES */ +#define CONFIG_ACCEL_FIFO +/* FIFO size is in power of 2. */ +#define CONFIG_ACCEL_FIFO_SIZE 256 +/* Depends on how fast the AP boots and typical ODRs */ +#define CONFIG_ACCEL_FIFO_THRES (CONFIG_ACCEL_FIFO_SIZE / 3) + +/* Sensors without hardware FIFO are in forced mode */ +#define CONFIG_ACCEL_FORCE_MODE_MASK \ + (BIT(LID_ACCEL) | BIT(CLEAR_ALS)) + +/* Lid accel */ +#define CONFIG_LID_ANGLE +#define CONFIG_LID_ANGLE_UPDATE +#define CONFIG_LID_ANGLE_SENSOR_BASE BASE_ACCEL +#define CONFIG_LID_ANGLE_SENSOR_LID LID_ACCEL +#define CONFIG_ACCEL_LIS2DWL +#define CONFIG_ACCEL_LIS2DW_AS_BASE +#define CONFIG_ACCEL_LIS2DW12_INT_EVENT \ + TASK_EVENT_MOTION_SENSOR_INTERRUPT(LID_ACCEL) + +#define CONFIG_ACCEL_INTERRUPTS + +/* Sensor console commands */ +#define CONFIG_CMD_ACCELS +#define CONFIG_CMD_ACCEL_INFO + +/* USB Type A Features */ +#define USB_PORT_COUNT 1 +#define CONFIG_USB_PORT_POWER_DUMB + +/* USB Type C and USB PD defines */ +#define CONFIG_USB_PD_REQUIRE_AP_MODE_ENTRY + +#define CONFIG_IO_EXPANDER +#define CONFIG_IO_EXPANDER_NCT38XX +#define CONFIG_IO_EXPANDER_PORT_COUNT 4 + +#define CONFIG_USB_PD_TCPM_PS8815 +#define CONFIG_USB_PD_TCPM_PS8815_FORCE_DID +#define CONFIG_USBC_RETIMER_INTEL_BB + +/* I2C speed console command */ +#define CONFIG_CMD_I2C_SPEED + +/* I2C control host command */ +#define CONFIG_HOSTCMD_I2C_CONTROL + +#define CONFIG_USBC_PPC_SYV682X +#define CONFIG_USBC_PPC_NX20P3483 + +/* TODO: b/177608416 - measure and check these values on brya */ +#define PD_POWER_SUPPLY_TURN_ON_DELAY 30000 /* us */ +#define PD_POWER_SUPPLY_TURN_OFF_DELAY 30000 /* us */ +#define PD_VCONN_SWAP_DELAY 5000 /* us */ + +/* + * Passive USB-C cables only support up to 60W. + */ +#define PD_OPERATING_POWER_MW 15000 +#define PD_MAX_POWER_MW 60000 +#define PD_MAX_CURRENT_MA 3000 +#define PD_MAX_VOLTAGE_MV 20000 + +/* + * Macros for GPIO signals used in common code that don't match the + * schematic names. Signal names in gpio.inc match the schematic and are + * then redefined here to so it's more clear which signal is being used for + * which purpose. + */ +#define GPIO_AC_PRESENT GPIO_ACOK_OD +#define GPIO_CPU_PROCHOT GPIO_EC_PROCHOT_ODL +#define GPIO_EC_INT_L GPIO_EC_PCH_INT_ODL +#define GPIO_ENABLE_BACKLIGHT GPIO_EC_EN_EDP_BL +#define GPIO_ENTERING_RW GPIO_EC_ENTERING_RW +#define GPIO_KBD_KSO2 GPIO_EC_KSO_02_INV +#define GPIO_PACKET_MODE_EN GPIO_EC_GSC_PACKET_MODE +#define GPIO_PCH_PWRBTN_L GPIO_EC_PCH_PWR_BTN_ODL +#define GPIO_PCH_RSMRST_L GPIO_EC_PCH_RSMRST_L +#define GPIO_PCH_RTCRST GPIO_EC_PCH_RTCRST +#define GPIO_PCH_SLP_S0_L GPIO_SYS_SLP_S0IX_L +#define GPIO_PCH_SLP_S3_L GPIO_SLP_S3_L +#define GMR_TABLET_MODE_GPIO_L GPIO_TABLET_MODE_L + +/* + * GPIO_EC_PCH_INT_ODL is used for MKBP events as well as a PCH wakeup + * signal. + */ +#define GPIO_PCH_WAKE_L GPIO_EC_PCH_INT_ODL +#define GPIO_PG_EC_ALL_SYS_PWRGD GPIO_SEQ_EC_ALL_SYS_PG +#define GPIO_PG_EC_DSW_PWROK GPIO_SEQ_EC_DSW_PWROK +#define GPIO_PG_EC_RSMRST_ODL GPIO_SEQ_EC_RSMRST_ODL +#define GPIO_POWER_BUTTON_L GPIO_GSC_EC_PWR_BTN_ODL +#define GPIO_SYS_RESET_L GPIO_SYS_RST_ODL +#define GPIO_VOLUME_DOWN_L GPIO_EC_VOLDN_BTN_ODL +#define GPIO_VOLUME_UP_L GPIO_EC_VOLUP_BTN_ODL +#define GPIO_WP_L GPIO_EC_WP_ODL + +#define GPIO_ID_1_EC_KB_BL_EN GPIO_EC_BATT_PRES_ODL + +/* System has back-lit keyboard */ +#define CONFIG_PWM_KBLIGHT + +/* I2C Bus Configuration */ + +#define I2C_PORT_SENSOR NPCX_I2C_PORT0_0 + +#define I2C_PORT_USB_C0_C2_TCPC NPCX_I2C_PORT1_0 +#define I2C_PORT_USB_C1_TCPC NPCX_I2C_PORT4_1 + +#define I2C_PORT_USB_C0_C2_PPC NPCX_I2C_PORT2_0 +#define I2C_PORT_USB_C1_PPC NPCX_I2C_PORT6_1 + +#define I2C_PORT_USB_C0_C2_BC12 NPCX_I2C_PORT2_0 +#define I2C_PORT_USB_C1_BC12 NPCX_I2C_PORT6_1 + +#define I2C_PORT_USB_C0_C2_MUX NPCX_I2C_PORT3_0 +#define I2C_PORT_USB_C1_MUX NPCX_I2C_PORT6_1 + +#define I2C_PORT_BATTERY NPCX_I2C_PORT5_0 +#define I2C_PORT_CHARGER NPCX_I2C_PORT7_0 +#define I2C_PORT_EEPROM NPCX_I2C_PORT7_0 +#define I2C_PORT_MP2964 NPCX_I2C_PORT7_0 + +#define I2C_ADDR_EEPROM_FLAGS 0x50 + +#define I2C_ADDR_MP2964_FLAGS 0x20 + +/* + * see b/174768555#comment22 + */ +#define USBC_PORT_C0_BB_RETIMER_I2C_ADDR 0x56 +#define USBC_PORT_C2_BB_RETIMER_I2C_ADDR 0x57 + +/* Enabling Thunderbolt-compatible mode */ +#define CONFIG_USB_PD_TBT_COMPAT_MODE + +/* Enabling USB4 mode */ +#define CONFIG_USB_PD_USB4 + +/* Retimer */ +#define CONFIG_USBC_RETIMER_FW_UPDATE + +/* Thermal features */ +#define CONFIG_THERMISTOR +#define CONFIG_TEMP_SENSOR +#define CONFIG_TEMP_SENSOR_POWER_GPIO GPIO_SEQ_EC_DSW_PWROK +#define CONFIG_STEINHART_HART_3V3_30K9_47K_4050B + +#define CONFIG_FANS FAN_CH_COUNT + +/* Charger defines */ +#define CONFIG_CHARGER_BQ25720 +#define CONFIG_CHARGER_BQ25720_VSYS_TH2_CUSTOM +#define CONFIG_CHARGER_BQ25720_VSYS_TH2_DV 70 +#define CONFIG_CHARGE_RAMP_SW +#define CONFIG_CHARGER_BQ25710_SENSE_RESISTOR 10 +#define CONFIG_CHARGER_BQ25710_SENSE_RESISTOR_AC 10 +#define CONFIG_CHARGER_BQ25710_PSYS_SENSING + +/* + * Older boards have a different ADC assignment. + */ + +#define CONFIG_ADC_CHANNELS_RUNTIME_CONFIG + +#ifndef __ASSEMBLER__ + +#include "gpio_signal.h" /* needed by registers.h */ +#include "registers.h" +#include "usbc_config.h" + +enum adc_channel { + ADC_TEMP_SENSOR_1_DDR_SOC, + ADC_TEMP_SENSOR_2_AMBIENT, + ADC_TEMP_SENSOR_3_CHARGER, + ADC_TEMP_SENSOR_4_WWAN, + ADC_CH_COUNT +}; + +enum temp_sensor_id { + TEMP_SENSOR_1_DDR_SOC, + TEMP_SENSOR_2_AMBIENT, + TEMP_SENSOR_3_CHARGER, + TEMP_SENSOR_4_WWAN, + TEMP_SENSOR_COUNT +}; + +enum sensor_id { + LID_ACCEL = 0, + BASE_ACCEL, + BASE_GYRO, + CLEAR_ALS, + RGB_ALS, + SENSOR_COUNT +}; + +enum ioex_port { + IOEX_C0_NCT38XX = 0, + IOEX_C2_NCT38XX, + IOEX_ID_1_C0_NCT38XX, + IOEX_ID_1_C2_NCT38XX, + IOEX_PORT_COUNT +}; + +enum battery_type { + BATTERY_POWER_TECH, + BATTERY_LGC011, + BATTERY_TYPE_COUNT +}; + +enum pwm_channel { + PWM_CH_LED2 = 0, /* PWM0 (white charger) */ + PWM_CH_LED3, /* PWM1 (orange on DB) */ + PWM_CH_LED1, /* PWM2 (orange charger) */ + PWM_CH_KBLIGHT, /* PWM3 */ + PWM_CH_FAN, /* PWM5 */ + PWM_CH_LED4, /* PWM7 (white on DB) */ + PWM_CH_COUNT +}; + +enum fan_channel { + FAN_CH_0 = 0, + FAN_CH_COUNT +}; + +enum mft_channel { + MFT_CH_0 = 0, + MFT_CH_COUNT +}; + +#endif /* !__ASSEMBLER__ */ + +#endif /* __CROS_EC_BOARD_H */ |