summaryrefslogtreecommitdiff
path: root/board/volteer/board.c
diff options
context:
space:
mode:
Diffstat (limited to 'board/volteer/board.c')
-rw-r--r--board/volteer/board.c247
1 files changed, 0 insertions, 247 deletions
diff --git a/board/volteer/board.c b/board/volteer/board.c
deleted file mode 100644
index 8c1be1bf64..0000000000
--- a/board/volteer/board.c
+++ /dev/null
@@ -1,247 +0,0 @@
-/* Copyright 2019 The Chromium OS Authors. All rights reserved.
- * Use of this source code is governed by a BSD-style license that can be
- * found in the LICENSE file.
- */
-
-/* Volteer board-specific configuration */
-#include "button.h"
-#include "common.h"
-#include "accelgyro.h"
-#include "cbi_ec_fw_config.h"
-#include "driver/accel_bma2x2.h"
-#include "driver/accelgyro_bmi260.h"
-#include "driver/als_tcs3400.h"
-#include "driver/retimer/bb_retimer_public.h"
-#include "driver/sync.h"
-#include "driver/tcpm/ps8xxx.h"
-#include "extpower.h"
-#include "fan.h"
-#include "fan_chip.h"
-#include "gpio.h"
-#include "hooks.h"
-#include "keyboard_scan.h"
-#include "lid_switch.h"
-#include "power.h"
-#include "power_button.h"
-#include "pwm.h"
-#include "pwm_chip.h"
-#include "switch.h"
-#include "system.h"
-#include "task.h"
-#include "tablet_mode.h"
-#include "throttle_ap.h"
-#include "timer.h"
-#include "uart.h"
-#include "usb_pd.h"
-#include "usb_pd_tbt.h"
-#include "usb_pd_tcpm.h"
-#include "util.h"
-
-#include "gpio_list.h" /* Must come after other header files. */
-
-#define CPRINTS(format, args...) cprints(CC_CHIPSET, format, ## args)
-
-/******************************************************************************/
-/* Keyboard scan setting */
-__override struct keyboard_scan_config keyscan_config = {
- /* Increase from 50 us, because KSO_02 passes through the H1. */
- .output_settle_us = 80,
- /* Other values should be the same as the default configuration. */
- .debounce_down_us = 9 * MSEC,
- .debounce_up_us = 30 * MSEC,
- .scan_period_us = 3 * MSEC,
- .min_post_scan_delay_us = 1000,
- .poll_timeout_us = 100 * MSEC,
- .actual_key_mask = {
- 0x14, 0xff, 0xff, 0xff, 0xff, 0xf5, 0xff,
- 0xa4, 0xff, 0xfe, 0x55, 0xfa, 0xca /* full set */
- },
-};
-
-/******************************************************************************/
-/* Physical fans. These are logically separate from pwm_channels. */
-
-const struct fan_conf fan_conf_0 = {
- .flags = FAN_USE_RPM_MODE,
- .ch = MFT_CH_0, /* Use MFT id to control fan */
- .pgood_gpio = -1,
- .enable_gpio = GPIO_EN_PP5000_FAN,
-};
-
-/*
- * Fan specs from datasheet:
- * Max speed 5900 rpm (+/- 7%), minimum duty cycle 30%.
- * Minimum speed not specified by RPM. Set minimum RPM to max speed (with
- * margin) x 30%.
- * 5900 x 1.07 x 0.30 = 1894, round up to 1900
- */
-const struct fan_rpm fan_rpm_0 = {
- .rpm_min = 1900,
- .rpm_start = 1900,
- .rpm_max = 5900,
-};
-
-const struct fan_t fans[FAN_CH_COUNT] = {
- [FAN_CH_0] = {
- .conf = &fan_conf_0,
- .rpm = &fan_rpm_0,
- },
-};
-
-/******************************************************************************/
-/* EC thermal management configuration */
-
-/*
- * Tiger Lake specifies 100 C as maximum TDP temperature. THRMTRIP# occurs at
- * 130 C. However, sensor is located next to DDR, so we need to use the lower
- * DDR temperature limit (85 C)
- */
-const static struct ec_thermal_config thermal_cpu = {
- .temp_host = {
- [EC_TEMP_THRESH_HIGH] = C_TO_K(70),
- [EC_TEMP_THRESH_HALT] = C_TO_K(80),
- },
- .temp_host_release = {
- [EC_TEMP_THRESH_HIGH] = C_TO_K(65),
- },
- .temp_fan_off = C_TO_K(35),
- .temp_fan_max = C_TO_K(50),
-};
-
-/*
- * Inductor limits - used for both charger and PP3300 regulator
- *
- * Need to use the lower of the charger IC, PP3300 regulator, and the inductors
- *
- * Charger max recommended temperature 100C, max absolute temperature 125C
- * PP3300 regulator: operating range -40 C to 145 C
- *
- * Inductors: limit of 125c
- * PCB: limit is 80c
- */
-const static struct ec_thermal_config thermal_inductor = {
- .temp_host = {
- [EC_TEMP_THRESH_HIGH] = C_TO_K(75),
- [EC_TEMP_THRESH_HALT] = C_TO_K(80),
- },
- .temp_host_release = {
- [EC_TEMP_THRESH_HIGH] = C_TO_K(65),
- },
- .temp_fan_off = C_TO_K(40),
- .temp_fan_max = C_TO_K(55),
-};
-
-
-struct ec_thermal_config thermal_params[] = {
- [TEMP_SENSOR_1_CHARGER] = thermal_inductor,
- [TEMP_SENSOR_2_PP3300_REGULATOR] = thermal_inductor,
- [TEMP_SENSOR_3_DDR_SOC] = thermal_cpu,
- [TEMP_SENSOR_4_FAN] = thermal_cpu,
-};
-BUILD_ASSERT(ARRAY_SIZE(thermal_params) == TEMP_SENSOR_COUNT);
-
-/******************************************************************************/
-/* MFT channels. These are logically separate from pwm_channels. */
-const struct mft_t mft_channels[] = {
- [MFT_CH_0] = {
- .module = NPCX_MFT_MODULE_1,
- .clk_src = TCKC_LFCLK,
- .pwm_id = PWM_CH_FAN,
- },
-};
-BUILD_ASSERT(ARRAY_SIZE(mft_channels) == MFT_CH_COUNT);
-
-/******************************************************************************/
-/* I2C port map configuration */
-const struct i2c_port_t i2c_ports[] = {
- {
- .name = "sensor",
- .port = I2C_PORT_SENSOR,
- .kbps = 400,
- .scl = GPIO_EC_I2C0_SENSOR_SCL,
- .sda = GPIO_EC_I2C0_SENSOR_SDA,
- },
- {
- .name = "usb_c0",
- .port = I2C_PORT_USB_C0,
- .kbps = 1000,
- .scl = GPIO_EC_I2C1_USB_C0_SCL,
- .sda = GPIO_EC_I2C1_USB_C0_SDA,
- },
- {
- .name = "usb_c1",
- .port = I2C_PORT_USB_C1,
- .kbps = 1000,
- .scl = GPIO_EC_I2C2_USB_C1_SCL,
- .sda = GPIO_EC_I2C2_USB_C1_SDA,
- },
- {
- .name = "usb_1_mix",
- .port = I2C_PORT_USB_1_MIX,
- .kbps = 100,
- .scl = GPIO_EC_I2C3_USB_1_MIX_SCL,
- .sda = GPIO_EC_I2C3_USB_1_MIX_SDA,
- },
- {
- .name = "power",
- .port = I2C_PORT_POWER,
- .kbps = 100,
- .scl = GPIO_EC_I2C5_BATTERY_SCL,
- .sda = GPIO_EC_I2C5_BATTERY_SDA,
- },
- {
- .name = "eeprom",
- .port = I2C_PORT_EEPROM,
- .kbps = 400,
- .scl = GPIO_EC_I2C7_EEPROM_PWR_SCL_R,
- .sda = GPIO_EC_I2C7_EEPROM_PWR_SDA_R,
- },
-};
-const unsigned int i2c_ports_used = ARRAY_SIZE(i2c_ports);
-
-/******************************************************************************/
-/* PWM configuration */
-const struct pwm_t pwm_channels[] = {
- [PWM_CH_LED1_BLUE] = {
- .channel = 2,
- .flags = PWM_CONFIG_ACTIVE_LOW | PWM_CONFIG_DSLEEP,
- .freq = 4800,
- },
- [PWM_CH_LED2_GREEN] = {
- .channel = 0,
- .flags = PWM_CONFIG_ACTIVE_LOW | PWM_CONFIG_DSLEEP,
- .freq = 4800,
- },
- [PWM_CH_LED3_RED] = {
- .channel = 1,
- .flags = PWM_CONFIG_ACTIVE_LOW | PWM_CONFIG_DSLEEP,
- .freq = 4800,
- },
- [PWM_CH_LED4_SIDESEL] = {
- .channel = 7,
- .flags = PWM_CONFIG_ACTIVE_LOW | PWM_CONFIG_DSLEEP,
- /*
- * If using the side select to run both LEDs at the same time,
- * the frequency should be 1/2 of the color channel PWM
- * frequency to drive each LED equally.
- */
- .freq = 2400,
- },
- [PWM_CH_FAN] = {
- .channel = 5,
- .flags = PWM_CONFIG_OPEN_DRAIN,
- .freq = 25000
- },
- [PWM_CH_KBLIGHT] = {
- .channel = 3,
- .flags = 0,
- /*
- * Set PWM frequency to multiple of 50 Hz and 60 Hz to prevent
- * flicker. Higher frequencies consume similar average power to
- * lower PWM frequencies, but higher frequencies record a much
- * lower maximum power.
- */
- .freq = 2400,
- },
-};
-BUILD_ASSERT(ARRAY_SIZE(pwm_channels) == PWM_CH_COUNT);
View Lorry Controller Status