diff options
Diffstat (limited to 'board/wolf/board.h')
| -rw-r--r-- | board/wolf/board.h | 201 |
1 files changed, 0 insertions, 201 deletions
diff --git a/board/wolf/board.h b/board/wolf/board.h deleted file mode 100644 index 5b208bd50c..0000000000 --- a/board/wolf/board.h +++ /dev/null @@ -1,201 +0,0 @@ -/* Copyright (c) 2013 The Chromium OS Authors. All rights reserved. - * Use of this source code is governed by a BSD-style license that can be - * found in the LICENSE file. - */ - -/* Configuration for Wolf mainboard */ - -#ifndef __BOARD_H -#define __BOARD_H - -/* Optional features */ -#define CONFIG_BACKLIGHT_X86 -#define CONFIG_BATTERY_SMART -#define CONFIG_BOARD_VERSION -#define CONFIG_CHARGER -#define CONFIG_CHARGER_BQ24707A -#define CONFIG_CHIPSET_HASWELL -#define CONFIG_CHIPSET_X86 -#define CONFIG_EXTPOWER_GPIO -#define CONFIG_KEYBOARD_BOARD_CONFIG -#define CONFIG_KEYBOARD_PROTOCOL_8042 -#define CONFIG_POWER_BUTTON -#define CONFIG_POWER_BUTTON_X86 -#define CONFIG_PWM_FAN -#define CONFIG_TEMP_SENSOR -#define CONFIG_UART_HOST 2 -#define CONFIG_TEMP_SENSOR_G781 -#define CONFIG_USB_PORT_POWER_DUMB -#define CONFIG_WIRELESS - -#ifndef __ASSEMBLER__ - -/* Module IDs */ -/* TODO(rspangler): use this in place of enum console_channel as well */ -enum module_id { - MODULE_I2C, - MODULE_LPC, - MODULE_PECI, - MODULE_PWM_FAN, - MODULE_UART, -}; - -/* PWM channels */ -#define FAN_CH_CPU 2 /* CPU fan */ -#define FAN_CH_BL_DISPLAY 4 /* LVDS backlight (from PCH, cleaned by EC) */ - -/* I2C ports */ -#define I2C_PORT_BATTERY 0 -#define I2C_PORT_CHARGER 0 -#define I2C_PORT_THERMAL 5 -/* There are only two I2C ports used because battery and charger share a port */ -#define I2C_PORTS_USED 2 - -/* 13x8 keyboard scanner uses an entire GPIO bank for row inputs */ -#define KB_SCAN_ROW_IRQ LM4_IRQ_GPIOK -#define KB_SCAN_ROW_GPIO LM4_GPIO_K - -/* Host connects to keyboard controller module via LPC */ -#define HOST_KB_BUS_LPC - -/* USB ports */ -#define USB_PORT_COUNT 2 - -/* GPIO signal definitions. */ -enum gpio_signal { - /* Inputs with interrupt handlers are first for efficiency */ - GPIO_POWER_BUTTON_L = 0, /* Power button */ - GPIO_LID_OPEN, /* Lid switch */ - GPIO_AC_PRESENT, /* AC power present */ - GPIO_PCH_BKLTEN, /* Backlight enable signal from PCH */ - GPIO_PCH_SLP_S0_L, /* SLP_S0# signal from PCH */ - GPIO_PCH_SLP_S3_L, /* SLP_S3# signal from PCH */ - GPIO_PCH_SLP_S5_L, /* SLP_S5# signal from PCH */ - GPIO_PCH_SLP_SUS_L, /* SLP_SUS# signal from PCH */ - GPIO_PP1050_PGOOD, /* Power good on 1.05V */ - GPIO_PP1350_PGOOD, /* Power good on 1.35V (DRAM) */ - GPIO_PP5000_PGOOD, /* Power good on 5V */ - GPIO_VCORE_PGOOD, /* Power good on core VR */ - GPIO_PCH_EDP_VDD_EN, /* PCH wants EDP enabled */ - GPIO_RECOVERY_L, /* Recovery signal from servo */ - GPIO_WP_L, /* Write protect input */ - - /* Other inputs */ - GPIO_FAN_ALERT_L, /* From thermal sensor */ - GPIO_PCH_SUSWARN_L, /* SUSWARN# signal from PCH */ - GPIO_USB1_OC_L, /* USB port overcurrent warning */ - GPIO_USB2_OC_L, /* USB port overcurrent warning */ - GPIO_BOARD_VERSION1, /* Board version stuffing resistor 1 */ - GPIO_BOARD_VERSION2, /* Board version stuffing resistor 2 */ - GPIO_BOARD_VERSION3, /* Board version stuffing resistor 3 */ - GPIO_CPU_PGOOD, /* Power good to the CPU */ - - /* Outputs */ - GPIO_CPU_PROCHOT, /* Force CPU to think it's overheated */ - GPIO_PP1350_EN, /* Enable 1.35V supply */ - GPIO_PP3300_DSW_GATED_EN, /* Enable DSW rails */ - GPIO_PP3300_DX_EN, /* Enable power to lots of peripherals */ - GPIO_PP3300_LTE_EN, /* Enable LTE radio */ - GPIO_PP3300_WLAN_EN, /* Enable WiFi power */ - GPIO_SUSP_VR_EN, /* Enable 1.05V regulator */ - GPIO_VCORE_EN, /* Stuffing option - not connected */ - GPIO_PP5000_EN, /* Enable 5V supply */ - GPIO_SYS_PWROK, /* EC thinks everything is up and ready */ - GPIO_WLAN_OFF_L, /* Disable WiFi radio */ - GPIO_CHARGE_L, /* Allow battery to charge when on AC */ - - GPIO_ENABLE_BACKLIGHT, /* Enable backlight power */ - GPIO_ENABLE_TOUCHPAD, /* Enable touchpad power */ - GPIO_ENTERING_RW, /* Indicate when EC is entering RW code */ - GPIO_PCH_DPWROK, /* Indicate when VccDSW is good */ - - GPIO_PCH_HDA_SDO, /* HDA_SDO signal to PCH; when high, ME - * ignores security descriptor */ - GPIO_PCH_WAKE_L, /* Wake signal from EC to PCH */ - GPIO_PCH_NMI_L, /* Non-maskable interrupt pin to PCH */ - GPIO_PCH_PWRBTN_L, /* Power button output to PCH */ - GPIO_PCH_PWROK, /* PWROK / APWROK signals to PCH */ - GPIO_PCH_RCIN_L, /* RCIN# line to PCH (for 8042 emulation) */ - GPIO_PCH_RSMRST_L, /* Reset PCH resume power plane logic */ - GPIO_PCH_SMI_L, /* System management interrupt to PCH */ - GPIO_TOUCHSCREEN_RESET_L, /* Reset touch screen */ - GPIO_EC_EDP_VDD_EN, /* Enable EDP (passthru from PCH) */ - GPOI_LPC_CLKRUN_L, /* Dunno. Probably important, though. */ - - GPIO_USB1_ENABLE, /* USB port 1 output power enable */ - GPIO_USB2_ENABLE, /* USB port 2 output power enable */ - - GPIO_PCH_SUSACK_L, /* Acknowledge PCH SUSWARN# signal */ - GPIO_PCH_RTCRST_L, /* Not supposed to be here */ - GPIO_PCH_SRTCRST_L, /* Not supposed to be here */ - - GPIO_BAT_LED0_L, /* Battery charging LED - Blue */ - GPIO_BAT_LED1_L, /* Battery charging LED - Amber */ - - /* Number of GPIOs; not an actual GPIO */ - GPIO_COUNT -}; - -/* x86 signal definitions */ -enum x86_signal { - X86_PGOOD_PP5000 = 0, - X86_PGOOD_PP1350, - X86_PGOOD_PP1050, - X86_PGOOD_VCORE, - X86_PCH_SLP_S0n_DEASSERTED, - X86_PCH_SLP_S3n_DEASSERTED, - X86_PCH_SLP_S5n_DEASSERTED, - X86_PCH_SLP_SUSn_DEASSERTED, - - /* Number of X86 signals */ - X86_SIGNAL_COUNT -}; - -/* Charger module */ -#define CONFIG_CHARGER_SENSE_RESISTOR 10 /* Charge sense resistor, mOhm */ -#define CONFIG_CHARGER_SENSE_RESISTOR_AC 10 /* Input sensor resistor, mOhm */ -/*FIXME needed to be checked, use the same as Peppy*/ -#define CONFIG_CHARGER_INPUT_CURRENT 3078 /* mA, need be checked */ - -enum adc_channel { - /* EC internal die temperature in degrees K. */ - ADC_CH_EC_TEMP = 0, - - /* HEY: Be prepared to read this (ICMNT). */ - /* Charger current in mA. */ - ADC_CH_CHARGER_CURRENT, - - ADC_CH_COUNT -}; - -enum temp_sensor_id { - /* CPU die temperature via PECI */ - TEMP_SENSOR_CPU_PECI = 0, - /* EC internal temperature sensor */ - TEMP_SENSOR_EC_INTERNAL, - /* G781 internal and external sensors */ - TEMP_SENSOR_I2C_G781_INTERNAL, - TEMP_SENSOR_I2C_G781_EXTERNAL, - - TEMP_SENSOR_COUNT -}; - -/** - * Board-specific g781 power state. - */ -int board_g781_has_power(void); - -/* Target value for BOOTCFG. This is set to PE2/USB1_CTL1, which has an external - * pullup. If this signal is pulled to ground when the EC boots, the EC will get - * into the boot loader and we can recover bricked EC. */ -#define BOOTCFG_VALUE 0x7fff88fe - -/* Wireless signals */ -#define WIRELESS_GPIO_WLAN GPIO_WLAN_OFF_L -#define WIRELESS_GPIO_WWAN GPIO_PP3300_LTE_EN -#define WIRELESS_GPIO_WLAN_POWER GPIO_PP3300_WLAN_EN - - -#endif /* !__ASSEMBLER__ */ - -#endif /* __BOARD_H */ |