diff options
Diffstat (limited to 'board/wormdingler')
-rw-r--r-- | board/wormdingler/base_detect.c | 234 | ||||
-rw-r--r-- | board/wormdingler/battery.c | 97 | ||||
-rw-r--r-- | board/wormdingler/board.c | 692 | ||||
-rw-r--r-- | board/wormdingler/board.h | 118 | ||||
-rw-r--r-- | board/wormdingler/build.mk | 14 | ||||
-rw-r--r-- | board/wormdingler/ec.tasklist | 22 | ||||
-rw-r--r-- | board/wormdingler/gpio.inc | 196 | ||||
-rw-r--r-- | board/wormdingler/led.c | 164 | ||||
-rw-r--r-- | board/wormdingler/vif_override.xml | 3 |
9 files changed, 0 insertions, 1540 deletions
diff --git a/board/wormdingler/base_detect.c b/board/wormdingler/base_detect.c deleted file mode 100644 index 73c28e4bc9..0000000000 --- a/board/wormdingler/base_detect.c +++ /dev/null @@ -1,234 +0,0 @@ -/* Copyright 2021 The Chromium OS Authors. All rights reserved. - * Use of this source code is governed by a BSD-style license that can be - * found in the LICENSE file. - */ - -/* Wormdingler base detection code */ - -#include "adc.h" -#include "base_state.h" -#include "board.h" -#include "chipset.h" -#include "common.h" -#include "console.h" -#include "gpio.h" -#include "hooks.h" -#include "host_command.h" -#include "system.h" -#include "tablet_mode.h" -#include "timer.h" -#include "util.h" - -#define CPRINTS(format, args...) cprints(CC_SYSTEM, format, ## args) -#define CPRINTF(format, args...) cprintf(CC_SYSTEM, format, ## args) - -/* Make sure POGO VBUS starts later then PP3300_HUB when power on */ -#define BASE_DETECT_EN_LATER_US (600 * MSEC) - -/* Base detection and debouncing */ -#define BASE_DETECT_EN_DEBOUNCE_US (350 * MSEC) -#define BASE_DETECT_DIS_DEBOUNCE_US (20 * MSEC) - -/* - * If the base status is unclear (i.e. not within expected ranges, read - * the ADC value again every 500ms. - */ -#define BASE_DETECT_RETRY_US (500 * MSEC) - -/* - * Lid has 604K pull-up, base has 30.1K pull-down, so the - * ADC value should be around 30.1/(604+30.1)*3300 = 156 - * - * We add a significant margin on the maximum value, due to noise on the line, - * especially when PWM is active. See b/64193554 for details. - */ -#define BASE_DETECT_MIN_MV 120 -#define BASE_DETECT_MAX_MV 300 - -/* Minimum ADC value to indicate base is disconnected for sure */ -#define BASE_DETECT_DISCONNECT_MIN_MV 1500 - -/* - * Base EC pulses detection pin for 500 us to signal out of band USB wake (that - * can be used to wake system from deep S3). - */ -#define BASE_DETECT_PULSE_MIN_US 400 -#define BASE_DETECT_PULSE_MAX_US 650 - -static uint64_t base_detect_debounce_time; - -static void base_detect_deferred(void); -DECLARE_DEFERRED(base_detect_deferred); - -enum base_status { - BASE_UNKNOWN = 0, - BASE_DISCONNECTED = 1, - BASE_CONNECTED = 2, -}; - -static enum base_status current_base_status; - -/* - * This function is called whenever there is a change in the base detect - * status. Actions taken include: - * 1. Change in power to base - * 2. Indicate mode change to host. - * 3. Indicate tablet mode to host. Current assumption is that if base is - * disconnected then the system is in tablet mode, else if the base is - * connected, then the system is not in tablet mode. - */ -static void base_detect_change(enum base_status status) -{ - int connected = (status == BASE_CONNECTED); - - if (current_base_status == status) - return; - - gpio_set_level(GPIO_EN_BASE, connected); - tablet_set_mode(!connected, TABLET_TRIGGER_BASE); - base_set_state(connected); - current_base_status = status; -} - -/* Measure detection pin pulse duration (used to wake AP from deep S3). */ -static uint64_t pulse_start; -static uint32_t pulse_width; - -static void print_base_detect_value(int v, int tmp_pulse_width) -{ - CPRINTS("%s = %d (pulse %d)", adc_channels[ADC_BASE_DET].name, - v, tmp_pulse_width); -} - -static void base_detect_deferred(void) -{ - uint64_t time_now = get_time().val; - int v; - uint32_t tmp_pulse_width = pulse_width; - - if (base_detect_debounce_time > time_now) { - hook_call_deferred(&base_detect_deferred_data, - base_detect_debounce_time - time_now); - return; - } - - v = adc_read_channel(ADC_BASE_DET); - if (v == ADC_READ_ERROR) - return; - - print_base_detect_value(v, tmp_pulse_width); - - if (v >= BASE_DETECT_MIN_MV && v <= BASE_DETECT_MAX_MV) { - if (current_base_status != BASE_CONNECTED) { - base_detect_change(BASE_CONNECTED); - } else if (tmp_pulse_width >= BASE_DETECT_PULSE_MIN_US && - tmp_pulse_width <= BASE_DETECT_PULSE_MAX_US) { - CPRINTS("Sending event to AP"); - host_set_single_event(EC_HOST_EVENT_KEY_PRESSED); - } - return; - } - - if (v >= BASE_DETECT_DISCONNECT_MIN_MV) { - base_detect_change(BASE_DISCONNECTED); - return; - } - - /* Unclear base status, schedule again in a while. */ - hook_call_deferred(&base_detect_deferred_data, BASE_DETECT_RETRY_US); -} - -static inline int detect_pin_connected(enum gpio_signal det_pin) -{ - return gpio_get_level(det_pin) == 0; -} - -void base_detect_interrupt(enum gpio_signal signal) -{ - uint64_t time_now = get_time().val; - int debounce_us; - - if (detect_pin_connected(signal)) - debounce_us = BASE_DETECT_EN_DEBOUNCE_US; - else - debounce_us = BASE_DETECT_DIS_DEBOUNCE_US; - - if (base_detect_debounce_time <= time_now) { - /* - * Detect and measure detection pin pulse, when base is - * connected. Only a single pulse is measured over a debounce - * period. If no pulse, or multiple pulses are detected, - * pulse_width is set to 0. - */ - if (current_base_status == BASE_CONNECTED && - !detect_pin_connected(signal)) { - pulse_start = time_now; - } else { - pulse_start = 0; - } - pulse_width = 0; - - hook_call_deferred(&base_detect_deferred_data, debounce_us); - } else { - if (current_base_status == BASE_CONNECTED && - detect_pin_connected(signal) && !pulse_width && - pulse_start) { - /* First pulse within period. */ - pulse_width = time_now - pulse_start; - } else { - pulse_start = 0; - pulse_width = 0; - } - } - - base_detect_debounce_time = time_now + debounce_us; -} - -static void base_enable(void) -{ - /* Enable base detection interrupt. */ - base_detect_debounce_time = get_time().val; - hook_call_deferred(&base_detect_deferred_data, - BASE_DETECT_EN_LATER_US); - gpio_enable_interrupt(GPIO_BASE_DET_L); -} -DECLARE_HOOK(HOOK_CHIPSET_STARTUP, base_enable, HOOK_PRIO_DEFAULT); - -static void base_disable(void) -{ - /* - * Disable base detection interrupt and disable power to base. - * Set the state UNKNOWN so the next startup will initialize a - * correct state and notify AP. - */ - gpio_disable_interrupt(GPIO_BASE_DET_L); - base_detect_change(BASE_UNKNOWN); -} -DECLARE_HOOK(HOOK_CHIPSET_SHUTDOWN, base_disable, HOOK_PRIO_DEFAULT); - -static void base_init(void) -{ - /* - * If we jumped to this image and chipset is already in S0, enable - * base. - */ - if (system_jumped_late() && chipset_in_state(CHIPSET_STATE_ON)) - base_enable(); -} -DECLARE_HOOK(HOOK_INIT, base_init, HOOK_PRIO_DEFAULT+1); - -void base_force_state(enum ec_set_base_state_cmd state) -{ - if (state == EC_SET_BASE_STATE_ATTACH) { - gpio_disable_interrupt(GPIO_BASE_DET_L); - base_detect_change(BASE_CONNECTED); - CPRINTS("BD forced connected"); - } else if (state == EC_SET_BASE_STATE_DETACH) { - gpio_disable_interrupt(GPIO_BASE_DET_L); - base_detect_change(BASE_DISCONNECTED); - CPRINTS("BD forced disconnected"); - } else { - base_enable(); - CPRINTS("BD forced reset"); - } -} diff --git a/board/wormdingler/battery.c b/board/wormdingler/battery.c deleted file mode 100644 index c76bb48031..0000000000 --- a/board/wormdingler/battery.c +++ /dev/null @@ -1,97 +0,0 @@ -/* Copyright 2021 The Chromium OS Authors. All rights reserved. - * Use of this source code is governed by a BSD-style license that can be - * found in the LICENSE file. - * - * Battery pack vendor provided charging profile - */ - -#include "battery_fuel_gauge.h" -#include "common.h" -#include "util.h" - -/* - * Battery info for all wormdingler battery types. Note that the fields - * start_charging_min/max and charging_min/max are not used for the charger. - * The effective temperature limits are given by discharging_min/max_c. - * - * Fuel Gauge (FG) parameters which are used for determining if the battery - * is connected, the appropriate ship mode (battery cutoff) command, and the - * charge/discharge FETs status. - * - * Ship mode (battery cutoff) requires 2 writes to the appropriate smart battery - * register. For some batteries, the charge/discharge FET bits are set when - * charging/discharging is active, in other types, these bits set mean that - * charging/discharging is disabled. Therefore, in addition to the mask for - * these bits, a disconnect value must be specified. Note that for TI fuel - * gauge, the charge/discharge FET status is found in Operation Status (0x54), - * but a read of Manufacturer Access (0x00) will return the lower 16 bits of - * Operation status which contains the FET status bits. - * - * The assumption for battery types supported is that the charge/discharge FET - * status can be read with a sb_read() command and therefore, only the register - * address, mask, and disconnect value need to be provided. - */ - -const struct board_batt_params board_battery_info[] = { - /* Sunwoda L21D2PG2 */ - [BATTERY_L21D2PG2] = { - .fuel_gauge = { - .manuf_name = "Sunwoda", - .device_name = "L21D2PG2", - .ship_mode = { - .reg_addr = 0x34, - .reg_data = { 0x0000, 0x1000 }, - }, - .fet = { - .mfgacc_support = 1, - .reg_addr = 0x34, - .reg_mask = 0x0100, - .disconnect_val = 0x0, - } - }, - .batt_info = { - .voltage_max = 8860, /* mV */ - .voltage_normal = 7700, /* mV */ - .voltage_min = 6000, /* mV */ - .precharge_current = 200, /* mA */ - .start_charging_min_c = 0, - .start_charging_max_c = 50, - .charging_min_c = 0, - .charging_max_c = 63, - .discharging_min_c = -20, - .discharging_max_c = 63, - }, - }, - /* BYD L21B2PG2 */ - [BATTERY_L21B2PG2] = { - .fuel_gauge = { - .manuf_name = "BYD", - .device_name = "L21B2PG2", - .ship_mode = { - .reg_addr = 0x34, - .reg_data = { 0x0000, 0x1000 }, - }, - .fet = { - .mfgacc_support = 1, - .reg_addr = 0x34, - .reg_mask = 0x0100, - .disconnect_val = 0x0, - } - }, - .batt_info = { - .voltage_max = 8860, /* mV */ - .voltage_normal = 7700, /* mV */ - .voltage_min = 6000, /* mV */ - .precharge_current = 256, /* mA */ - .start_charging_min_c = 0, - .start_charging_max_c = 50, - .charging_min_c = 0, - .charging_max_c = 60, - .discharging_min_c = -20, - .discharging_max_c = 60, - }, - }, -}; -BUILD_ASSERT(ARRAY_SIZE(board_battery_info) == BATTERY_TYPE_COUNT); - -const enum battery_type DEFAULT_BATTERY_TYPE = BATTERY_L21D2PG2; diff --git a/board/wormdingler/board.c b/board/wormdingler/board.c deleted file mode 100644 index 796409cb80..0000000000 --- a/board/wormdingler/board.c +++ /dev/null @@ -1,692 +0,0 @@ -/* Copyright 2021 The Chromium OS Authors. All rights reserved. - * Use of this source code is governed by a BSD-style license that can be - * found in the LICENSE file. - */ - -/* Wormdingler board-specific configuration */ - -#include "adc_chip.h" -#include "button.h" -#include "charge_manager.h" -#include "charge_state.h" -#include "common.h" -#include "extpower.h" -#include "driver/accel_bma2x2.h" -#include "driver/accelgyro_bmi_common.h" -#include "driver/accelgyro_icm_common.h" -#include "driver/accelgyro_icm42607.h" -#include "driver/ln9310.h" -#include "driver/ppc/sn5s330.h" -#include "driver/tcpm/ps8xxx.h" -#include "driver/tcpm/tcpci.h" -#include "gpio.h" -#include "hooks.h" -#include "keyboard_mkbp.h" -#include "keyboard_scan.h" -#include "lid_switch.h" -#include "peripheral_charger.h" -#include "pi3usb9201.h" -#include "power.h" -#include "power/qcom.h" -#include "power_button.h" -#include "pwm.h" -#include "pwm_chip.h" -#include "queue.h" -#include "system.h" -#include "shi_chip.h" -#include "switch.h" -#include "tablet_mode.h" -#include "task.h" -#include "usbc_ppc.h" - -#define CPRINTS(format, args...) cprints(CC_USBCHARGE, format, ## args) -#define CPRINTF(format, args...) cprintf(CC_USBCHARGE, format, ## args) - -#define KS_DEBOUNCE_US (30 * MSEC) /* Debounce time for kickstand switch */ - -/* Forward declaration */ -static void tcpc_alert_event(enum gpio_signal signal); -static void usb0_evt(enum gpio_signal signal); -static void usb1_evt(enum gpio_signal signal); -static void ppc_interrupt(enum gpio_signal signal); -static void board_connect_c0_sbu(enum gpio_signal s); -static void switchcap_interrupt(enum gpio_signal signal); - -#include "gpio_list.h" - -/* GPIO Interrupt Handlers */ -static void tcpc_alert_event(enum gpio_signal signal) -{ - int port = -1; - - switch (signal) { - case GPIO_USB_C0_PD_INT_ODL: - port = 0; - break; - case GPIO_USB_C1_PD_INT_ODL: - port = 1; - break; - default: - return; - } - - schedule_deferred_pd_interrupt(port); -} - -static void usb0_evt(enum gpio_signal signal) -{ - task_set_event(TASK_ID_USB_CHG_P0, USB_CHG_EVENT_BC12); -} - -static void usb1_evt(enum gpio_signal signal) -{ - task_set_event(TASK_ID_USB_CHG_P1, USB_CHG_EVENT_BC12); -} - -static void ppc_interrupt(enum gpio_signal signal) -{ - switch (signal) { - case GPIO_USB_C0_SWCTL_INT_ODL: - sn5s330_interrupt(0); - break; - case GPIO_USB_C1_SWCTL_INT_ODL: - sn5s330_interrupt(1); - break; - default: - break; - } -} - -static void board_connect_c0_sbu_deferred(void) -{ - /* - * If CCD_MODE_ODL asserts, it means there's a debug accessory connected - * and we should enable the SBU FETs. - */ - ppc_set_sbu(0, 1); -} -DECLARE_DEFERRED(board_connect_c0_sbu_deferred); - -static void board_connect_c0_sbu(enum gpio_signal s) -{ - hook_call_deferred(&board_connect_c0_sbu_deferred_data, 0); -} - -static void switchcap_interrupt(enum gpio_signal signal) -{ - ln9310_interrupt(signal); -} - -/* I2C port map */ -const struct i2c_port_t i2c_ports[] = { - {"power", I2C_PORT_POWER, 100, GPIO_EC_I2C_POWER_SCL, - GPIO_EC_I2C_POWER_SDA}, - {"tcpc0", I2C_PORT_TCPC0, 1000, GPIO_EC_I2C_USB_C0_PD_SCL, - GPIO_EC_I2C_USB_C0_PD_SDA}, - {"tcpc1", I2C_PORT_TCPC1, 1000, GPIO_EC_I2C_USB_C1_PD_SCL, - GPIO_EC_I2C_USB_C1_PD_SDA}, - {"eeprom", I2C_PORT_EEPROM, 400, GPIO_EC_I2C_EEPROM_SCL, - GPIO_EC_I2C_EEPROM_SDA}, - {"sensor", I2C_PORT_SENSOR, 400, GPIO_EC_I2C_SENSOR_SCL, - GPIO_EC_I2C_SENSOR_SDA}, -}; - -const unsigned int i2c_ports_used = ARRAY_SIZE(i2c_ports); - -/* ADC channels */ -const struct adc_t adc_channels[] = { - /* Measure VBUS through a 1/10 voltage divider */ - [ADC_VBUS] = { - "VBUS", - NPCX_ADC_CH1, - ADC_MAX_VOLT * 10, - ADC_READ_MAX + 1, - 0 - }, - /* - * Adapter current output or battery charging/discharging current (uV) - * 18x amplification on charger side. - */ - [ADC_AMON_BMON] = { - "AMON_BMON", - NPCX_ADC_CH2, - ADC_MAX_VOLT * 1000 / 18, - ADC_READ_MAX + 1, - 0 - }, - /* - * ISL9238 PSYS output is 1.44 uA/W over 5.6K resistor, to read - * 0.8V @ 99 W, i.e. 124000 uW/mV. Using ADC_MAX_VOLT*124000 and - * ADC_READ_MAX+1 as multiplier/divider leads to overflows, so we - * only divide by 2 (enough to avoid precision issues). - */ - [ADC_PSYS] = { - "PSYS", - NPCX_ADC_CH3, - ADC_MAX_VOLT * 124000 * 2 / (ADC_READ_MAX + 1), - 2, - 0 - }, - /* Base detection */ - [ADC_BASE_DET] = { - "BASE_DET", - NPCX_ADC_CH5, - ADC_MAX_VOLT, - ADC_READ_MAX + 1, - 0 - }, -}; -BUILD_ASSERT(ARRAY_SIZE(adc_channels) == ADC_CH_COUNT); - -const struct pwm_t pwm_channels[] = { - /* TODO(waihong): Assign a proper frequency. */ - [PWM_CH_DISPLIGHT] = { .channel = 5, .flags = 0, .freq = 4800 }, -}; -BUILD_ASSERT(ARRAY_SIZE(pwm_channels) == PWM_CH_COUNT); - -/* LN9310 switchcap */ -const struct ln9310_config_t ln9310_config = { - .i2c_port = I2C_PORT_POWER, - .i2c_addr_flags = LN9310_I2C_ADDR_0_FLAGS, -}; - -/* Power Path Controller */ -struct ppc_config_t ppc_chips[] = { - { - .i2c_port = I2C_PORT_TCPC0, - .i2c_addr_flags = SN5S330_ADDR0_FLAGS, - .drv = &sn5s330_drv - }, - { - .i2c_port = I2C_PORT_TCPC1, - .i2c_addr_flags = SN5S330_ADDR0_FLAGS, - .drv = &sn5s330_drv - }, -}; -unsigned int ppc_cnt = ARRAY_SIZE(ppc_chips); - -/* TCPC mux configuration */ -const struct tcpc_config_t tcpc_config[CONFIG_USB_PD_PORT_MAX_COUNT] = { - { - .bus_type = EC_BUS_TYPE_I2C, - .i2c_info = { - .port = I2C_PORT_TCPC0, - .addr_flags = PS8751_I2C_ADDR1_FLAGS, - }, - .drv = &ps8xxx_tcpm_drv, - }, - { - .bus_type = EC_BUS_TYPE_I2C, - .i2c_info = { - .port = I2C_PORT_TCPC1, - .addr_flags = PS8751_I2C_ADDR1_FLAGS, - }, - .drv = &ps8xxx_tcpm_drv, - }, -}; - -/* - * Port-0/1 USB mux driver. - * - * The USB mux is handled by TCPC chip and the HPD update is through a GPIO - * to AP. But the TCPC chip is also needed to know the HPD status; otherwise, - * the mux misbehaves. - */ -const struct usb_mux usb_muxes[CONFIG_USB_PD_PORT_MAX_COUNT] = { - { - .usb_port = 0, - .driver = &tcpci_tcpm_usb_mux_driver, - .hpd_update = &ps8xxx_tcpc_update_hpd_status, - }, - { - .usb_port = 1, - .driver = &tcpci_tcpm_usb_mux_driver, - .hpd_update = &ps8xxx_tcpc_update_hpd_status, - } -}; - -/* BC1.2 */ -const struct pi3usb9201_config_t pi3usb9201_bc12_chips[] = { - { - .i2c_port = I2C_PORT_POWER, - .i2c_addr_flags = PI3USB9201_I2C_ADDR_3_FLAGS, - }, - { - .i2c_port = I2C_PORT_EEPROM, - .i2c_addr_flags = PI3USB9201_I2C_ADDR_3_FLAGS, - }, -}; - -/* Mutexes */ -static struct mutex g_lid_mutex; - -static struct bmi_drv_data_t g_bmi160_data; -static struct icm_drv_data_t g_icm42607_data; - -enum lid_accelgyro_type { - LID_GYRO_NONE = 0, - LID_GYRO_BMI160 = 1, - LID_GYRO_ICM42607 = 2, -}; - -static enum lid_accelgyro_type lid_accelgyro_config; - -/* Matrix to rotate accelerometer into standard reference frame */ -const mat33_fp_t lid_standard_ref = { - { FLOAT_TO_FP(1), 0, 0}, - { 0, FLOAT_TO_FP(1), 0}, - { 0, 0, FLOAT_TO_FP(1)} -}; - -const mat33_fp_t lid_standard_ref_icm42607 = { - { 0, FLOAT_TO_FP(-1), 0}, - { FLOAT_TO_FP(1), 0, 0}, - { 0, 0, FLOAT_TO_FP(1)} -}; - -struct motion_sensor_t icm42607_lid_accel = { - .name = "Lid Accel", - .active_mask = SENSOR_ACTIVE_S0_S3, - .chip = MOTIONSENSE_CHIP_ICM42607, - .type = MOTIONSENSE_TYPE_ACCEL, - .location = MOTIONSENSE_LOC_LID, - .drv = &icm42607_drv, - .mutex = &g_lid_mutex, - .drv_data = &g_icm42607_data, - .port = I2C_PORT_SENSOR, - .i2c_spi_addr_flags = ICM42607_ADDR0_FLAGS, - .rot_standard_ref = &lid_standard_ref_icm42607, - .default_range = 4, /* g, to meet CDD 7.3.1/C-1-4 reqs */ - .min_frequency = ICM42607_ACCEL_MIN_FREQ, - .max_frequency = ICM42607_ACCEL_MAX_FREQ, - .config = { - [SENSOR_CONFIG_EC_S0] = { - .odr = 10000 | ROUND_UP_FLAG, - }, - }, -}; - -struct motion_sensor_t icm42607_lid_gyro = { - .name = "Gyro", - .active_mask = SENSOR_ACTIVE_S0_S3, - .chip = MOTIONSENSE_CHIP_ICM42607, - .type = MOTIONSENSE_TYPE_GYRO, - .location = MOTIONSENSE_LOC_LID, - .drv = &icm42607_drv, - .mutex = &g_lid_mutex, - .drv_data = &g_icm42607_data, - .port = I2C_PORT_SENSOR, - .i2c_spi_addr_flags = ICM42607_ADDR0_FLAGS, - .default_range = 1000, /* dps */ - .rot_standard_ref = &lid_standard_ref_icm42607, - .min_frequency = ICM42607_GYRO_MIN_FREQ, - .max_frequency = ICM42607_GYRO_MAX_FREQ, -}; - -struct motion_sensor_t motion_sensors[] = { - /* - * Note: bmi160: supports accelerometer and gyro sensor - * Requirement: accelerometer sensor must init before gyro sensor - * DO NOT change the order of the following table. - */ - [LID_ACCEL] = { - .name = "Lid Accel", - .active_mask = SENSOR_ACTIVE_S0_S3, - .chip = MOTIONSENSE_CHIP_BMI160, - .type = MOTIONSENSE_TYPE_ACCEL, - .location = MOTIONSENSE_LOC_LID, - .drv = &bmi160_drv, - .mutex = &g_lid_mutex, - .drv_data = &g_bmi160_data, - .port = I2C_PORT_SENSOR, - .i2c_spi_addr_flags = BMI160_ADDR0_FLAGS, - .rot_standard_ref = &lid_standard_ref, - .default_range = 4, /* g, to meet CDD 7.3.1/C-1-4 reqs */ - .min_frequency = BMI_ACCEL_MIN_FREQ, - .max_frequency = BMI_ACCEL_MAX_FREQ, - .config = { - [SENSOR_CONFIG_EC_S0] = { - .odr = 10000 | ROUND_UP_FLAG, - }, - }, - }, - [LID_GYRO] = { - .name = "Gyro", - .active_mask = SENSOR_ACTIVE_S0_S3, - .chip = MOTIONSENSE_CHIP_BMI160, - .type = MOTIONSENSE_TYPE_GYRO, - .location = MOTIONSENSE_LOC_LID, - .drv = &bmi160_drv, - .mutex = &g_lid_mutex, - .drv_data = &g_bmi160_data, - .port = I2C_PORT_SENSOR, - .i2c_spi_addr_flags = BMI160_ADDR0_FLAGS, - .default_range = 1000, /* dps */ - .rot_standard_ref = &lid_standard_ref, - .min_frequency = BMI_GYRO_MIN_FREQ, - .max_frequency = BMI_GYRO_MAX_FREQ, - }, -}; -const unsigned int motion_sensor_count = ARRAY_SIZE(motion_sensors); - -static void board_detect_motionsensor(void) -{ - int val = -1; - - if (chipset_in_state(CHIPSET_STATE_ANY_OFF)) - return; - if (lid_accelgyro_config != LID_GYRO_NONE) - return; - - /* Check base accelgyro chip */ - icm_read8(&icm42607_lid_accel, ICM42607_REG_WHO_AM_I, &val); - if (val == ICM42607_CHIP_ICM42607P) { - motion_sensors[LID_ACCEL] = icm42607_lid_accel; - motion_sensors[LID_GYRO] = icm42607_lid_gyro; - lid_accelgyro_config = LID_GYRO_ICM42607; - CPRINTS("LID Accelgyro: ICM42607"); - } else { - lid_accelgyro_config = LID_GYRO_BMI160; - CPRINTS("LID Accelgyro: BMI160"); - } -} -DECLARE_HOOK(HOOK_CHIPSET_STARTUP, board_detect_motionsensor, - HOOK_PRIO_DEFAULT); -DECLARE_HOOK(HOOK_INIT, board_detect_motionsensor, HOOK_PRIO_DEFAULT + 1); - -void motion_interrupt(enum gpio_signal signal) -{ - switch (lid_accelgyro_config) { - case LID_GYRO_ICM42607: - icm42607_interrupt(signal); - break; - case LID_GYRO_BMI160: - default: - bmi160_interrupt(signal); - break; - } -} - -enum battery_cell_type board_get_battery_cell_type(void) -{ - return BATTERY_CELL_TYPE_2S; -} - -static void board_switchcap_init(void) -{ - CPRINTS("Use switchcap: LN9310"); - - /* Configure and enable interrupt for LN9310 */ - gpio_set_flags(GPIO_SWITCHCAP_PG_INT_L, GPIO_INT_FALLING); - gpio_enable_interrupt(GPIO_SWITCHCAP_PG_INT_L); - - /* Only configure the switchcap if not sysjump */ - if (!system_jumped_late()) - ln9310_init(); -} - -/* Initialize board. */ -static void board_init(void) -{ - /* Enable BC1.2 interrupts */ - gpio_enable_interrupt(GPIO_USB_C0_BC12_INT_L); - gpio_enable_interrupt(GPIO_USB_C1_BC12_INT_L); - gpio_enable_interrupt(GPIO_ACCEL_GYRO_INT_L); - - /* - * The H1 SBU line for CCD are behind PPC chip. The PPC internal FETs - * for SBU may be disconnected after DP alt mode is off. Should enable - * the CCD_MODE_ODL interrupt to make sure the SBU FETs are connected. - */ - gpio_enable_interrupt(GPIO_CCD_MODE_ODL); - - /* Set the backlight duty cycle to 0. AP will override it later. */ - pwm_set_duty(PWM_CH_DISPLIGHT, 0); - - board_switchcap_init(); -} -DECLARE_HOOK(HOOK_INIT, board_init, HOOK_PRIO_DEFAULT); - -__overridable uint16_t board_get_ps8xxx_product_id(int port) -{ - return PS8805_PRODUCT_ID; -} - -void board_tcpc_init(void) -{ - /* Only reset TCPC if not sysjump */ - if (!system_jumped_late()) { - /* TODO(crosbug.com/p/61098): How long do we need to wait? */ - board_reset_pd_mcu(); - } - - /* Enable PPC interrupts */ - gpio_enable_interrupt(GPIO_USB_C0_SWCTL_INT_ODL); - - /* Enable TCPC interrupts */ - gpio_enable_interrupt(GPIO_USB_C0_PD_INT_ODL); - gpio_enable_interrupt(GPIO_USB_C1_PD_INT_ODL); - - /* - * Initialize HPD to low; after sysjump SOC needs to see - * HPD pulse to enable video path - */ - for (int port = 0; port < CONFIG_USB_PD_PORT_MAX_COUNT; ++port) - usb_mux_hpd_update(port, USB_PD_MUX_HPD_LVL_DEASSERTED | - USB_PD_MUX_HPD_IRQ_DEASSERTED); -} -DECLARE_HOOK(HOOK_INIT, board_tcpc_init, HOOK_PRIO_INIT_I2C + 1); - -void board_hibernate(void) -{ - int i; - - /* - * Sensors are unpowered in hibernate. Apply PD to the - * interrupt lines such that they don't float. - */ - gpio_set_flags(GPIO_ACCEL_GYRO_INT_L, - GPIO_INPUT | GPIO_PULL_DOWN); - - /* - * Board rev 1+ has the hardware fix. Don't need the following - * workaround. - */ - if (system_get_board_version() >= 1) - return; - - /* - * Enable the PPC power sink path before EC enters hibernate; - * otherwise, ACOK won't go High and can't wake EC up. Check the - * bug b/170324206 for details. - */ - for (i = 0; i < CONFIG_USB_PD_PORT_MAX_COUNT; i++) - ppc_vbus_sink_enable(i, 1); -} - -/* Called on AP S0 -> S3 transition */ -static void board_chipset_suspend(void) -{ - /* - * Turn off display backlight in S3. AP has its own control. The EC's - * and the AP's will be AND'ed together in hardware. - */ - gpio_set_level(GPIO_ENABLE_BACKLIGHT, 0); - pwm_enable(PWM_CH_DISPLIGHT, 0); -} -DECLARE_HOOK(HOOK_CHIPSET_SUSPEND, board_chipset_suspend, HOOK_PRIO_DEFAULT); - -/* Called on AP S3 -> S0 transition */ -static void board_chipset_resume(void) -{ - /* Turn on display and keyboard backlight in S0. */ - gpio_set_level(GPIO_ENABLE_BACKLIGHT, 1); - if (pwm_get_duty(PWM_CH_DISPLIGHT)) - pwm_enable(PWM_CH_DISPLIGHT, 1); -} -DECLARE_HOOK(HOOK_CHIPSET_RESUME, board_chipset_resume, HOOK_PRIO_DEFAULT); - -void board_set_switchcap_power(int enable) -{ - gpio_set_level(GPIO_SWITCHCAP_ON_L, !enable); - ln9310_software_enable(enable); -} - -int board_is_switchcap_enabled(void) -{ - return !gpio_get_level(GPIO_SWITCHCAP_ON_L); -} - -int board_is_switchcap_power_good(void) -{ - return ln9310_power_good(); -} - -void board_reset_pd_mcu(void) -{ - cprints(CC_USB, "Resetting TCPCs..."); - cflush(); - - gpio_set_level(GPIO_USB_C0_PD_RST_L, 0); - gpio_set_level(GPIO_USB_C1_PD_RST_L, 0); - msleep(PS8XXX_RESET_DELAY_MS); - gpio_set_level(GPIO_USB_C0_PD_RST_L, 1); - gpio_set_level(GPIO_USB_C1_PD_RST_L, 1); -} - -void board_set_tcpc_power_mode(int port, int mode) -{ - /* Ignore the "mode" to turn the chip on. We can only do a reset. */ - if (mode) - return; - - board_reset_pd_mcu(); -} - -int board_vbus_sink_enable(int port, int enable) -{ - /* Both ports are controlled by PPC SN5S330 */ - return ppc_vbus_sink_enable(port, enable); -} - -int board_is_sourcing_vbus(int port) -{ - /* Both ports are controlled by PPC SN5S330 */ - return ppc_is_sourcing_vbus(port); -} - -void board_overcurrent_event(int port, int is_overcurrented) -{ - /* TODO(b/120231371): Notify AP */ - CPRINTS("p%d: overcurrent!", port); -} - -int board_set_active_charge_port(int port) -{ - int is_real_port = (port >= 0 && - port < CONFIG_USB_PD_PORT_MAX_COUNT); - int i; - - if (!is_real_port && port != CHARGE_PORT_NONE) - return EC_ERROR_INVAL; - - if (port == CHARGE_PORT_NONE) { - CPRINTS("Disabling all charging port"); - - /* Disable all ports. */ - for (i = 0; i < CONFIG_USB_PD_PORT_MAX_COUNT; i++) { - /* - * Do not return early if one fails otherwise we can - * get into a boot loop assertion failure. - */ - if (board_vbus_sink_enable(i, 0)) - CPRINTS("Disabling p%d sink path failed.", i); - } - - return EC_SUCCESS; - } - - /* Check if the port is sourcing VBUS. */ - if (board_is_sourcing_vbus(port)) { - CPRINTS("Skip enable p%d", port); - return EC_ERROR_INVAL; - } - - CPRINTS("New charge port: p%d", port); - - /* - * Turn off the other ports' sink path FETs, before enabling the - * requested charge port. - */ - for (i = 0; i < CONFIG_USB_PD_PORT_MAX_COUNT; i++) { - if (i == port) - continue; - - if (board_vbus_sink_enable(i, 0)) - CPRINTS("p%d: sink path disable failed.", i); - } - - /* Enable requested charge port. */ - if (board_vbus_sink_enable(port, 1)) { - CPRINTS("p%d: sink path enable failed.", port); - return EC_ERROR_UNKNOWN; - } - - return EC_SUCCESS; -} - -void board_set_charge_limit(int port, int supplier, int charge_ma, - int max_ma, int charge_mv) -{ - /* - * Ignore lower charge ceiling on PD transition if our battery is - * critical, as we may brownout. - */ - if (supplier == CHARGE_SUPPLIER_PD && - charge_ma < 1500 && - charge_get_percent() < CONFIG_CHARGER_MIN_BAT_PCT_FOR_POWER_ON) { - CPRINTS("Using max ilim %d", max_ma); - charge_ma = max_ma; - } - - charge_ma = charge_ma * 95 / 100; - charge_set_input_current_limit(MAX(charge_ma, - CONFIG_CHARGER_INPUT_CURRENT), - charge_mv); -} - -uint16_t tcpc_get_alert_status(void) -{ - uint16_t status = 0; - - if (!gpio_get_level(GPIO_USB_C0_PD_INT_ODL)) - if (gpio_get_level(GPIO_USB_C0_PD_RST_L)) - status |= PD_STATUS_TCPC_ALERT_0; - if (!gpio_get_level(GPIO_USB_C1_PD_INT_ODL)) - if (gpio_get_level(GPIO_USB_C1_PD_RST_L)) - status |= PD_STATUS_TCPC_ALERT_1; - - return status; -} - -int battery_get_vendor_param(uint32_t param, uint32_t *value) -{ - int rv; - uint8_t data[16] = {}; - - /* only allow reading 0x70~0x7F, 16 byte data */ - if (param < 0x70 || param >= 0x80) - return EC_ERROR_ACCESS_DENIED; - - rv = sb_read_string(0x70, data, sizeof(data)); - if (rv) - return rv; - - *value = data[param - 0x70]; - return EC_SUCCESS; -} - -int battery_set_vendor_param(uint32_t param, uint32_t value) -{ - return EC_ERROR_UNIMPLEMENTED; -} diff --git a/board/wormdingler/board.h b/board/wormdingler/board.h deleted file mode 100644 index af0b5ee80d..0000000000 --- a/board/wormdingler/board.h +++ /dev/null @@ -1,118 +0,0 @@ -/* Copyright 2021 The Chromium OS Authors. All rights reserved. - * Use of this source code is governed by a BSD-style license that can be - * found in the LICENSE file. - */ - -/* Wormdingler board configuration */ - -#ifndef __CROS_EC_BOARD_H -#define __CROS_EC_BOARD_H - -#include "baseboard.h" - -/* TODO(waihong): Remove the following bringup features */ -#define CONFIG_BRINGUP -#define CONFIG_SYSTEM_UNLOCKED /* Allow dangerous commands. */ -#define CONFIG_USB_PD_DEBUG_LEVEL 3 -#define CONFIG_CMD_GPIO_EXTENDED -#define CONFIG_CMD_POWERINDEBUG -#define CONFIG_I2C_DEBUG - -#define CONFIG_BUTTON_TRIGGERED_RECOVERY - -/* Internal SPI flash on NPCX7 */ -#define CONFIG_FLASH_SIZE_BYTES (512 * 1024) /* 512KB internal spi flash */ - -/* Switchcap */ -#define CONFIG_LN9310 - -/* Battery */ -#define CONFIG_BATTERY_DEVICE_CHEMISTRY "LION" -#define CONFIG_BATTERY_REVIVE_DISCONNECT -#define CONFIG_BATTERY_FUEL_GAUGE -#define CONFIG_BATTERY_VENDOR_PARAM -#define CONFIG_BATTERY_V2 -#define CONFIG_BATTERY_COUNT 1 -#define CONFIG_HOSTCMD_BATTERY_V2 - -/* Enable PD3.0 */ -#define CONFIG_USB_PD_REV30 - -/* BC 1.2 Charger */ -#define CONFIG_BC12_DETECT_PI3USB9201 - -/* USB */ -#define CONFIG_USB_PD_TCPM_MULTI_PS8XXX -#define CONFIG_USB_PD_TCPM_PS8755 -#define CONFIG_USB_PD_TCPM_PS8805 -#define CONFIG_USBC_PPC_SN5S330 -#define CONFIG_USB_PD_PORT_MAX_COUNT 2 - -/* Lid accel/gyro */ -#define CONFIG_ACCELGYRO_BMI160 -#define CONFIG_ACCEL_INTERRUPTS -#define CONFIG_ACCELGYRO_BMI160_INT_EVENT \ - TASK_EVENT_MOTION_SENSOR_INTERRUPT(LID_ACCEL) -#define OPT3001_I2C_ADDR_FLAGS OPT3001_I2C_ADDR1_FLAGS -#define CONFIG_ACCELGYRO_ICM42607 -#define CONFIG_ACCELGYRO_ICM42607_INT_EVENT \ - TASK_EVENT_MOTION_SENSOR_INTERRUPT(LID_ACCEL) - -#define CONFIG_TABLET_MODE -#define CONFIG_TABLET_MODE_SWITCH -#define CONFIG_FRONT_PROXIMITY_SWITCH - -#define CONFIG_DETACHABLE_BASE -#define CONFIG_BASE_ATTACHED_SWITCH - -/* GPIO alias */ -#define GPIO_AC_PRESENT GPIO_CHG_ACOK_OD -#define GPIO_WP_L GPIO_EC_FLASH_WP_ODL -#define GPIO_PMIC_RESIN_L GPIO_PM845_RESIN_L -#define GPIO_SWITCHCAP_PG_INT_L GPIO_LN9310_INT - -#define CONFIG_MKBP_INPUT_DEVICES - -#ifndef __ASSEMBLER__ - -#include "gpio_signal.h" -#include "registers.h" - -enum adc_channel { - ADC_VBUS, - ADC_AMON_BMON, - ADC_PSYS, - ADC_BASE_DET, - ADC_CH_COUNT -}; - -/* Motion sensors */ -enum sensor_id { - LID_ACCEL = 0, - LID_GYRO, - SENSOR_COUNT, -}; - -enum pwm_channel { - PWM_CH_DISPLIGHT = 0, - PWM_CH_COUNT -}; - -/* List of possible batteries */ -enum battery_type { - BATTERY_L21D2PG2, - BATTERY_L21B2PG2, - BATTERY_TYPE_COUNT, -}; - -/* Reset all TCPCs. */ -void board_reset_pd_mcu(void); -void board_set_tcpc_power_mode(int port, int mode); -/* Base detection */ -void base_detect_interrupt(enum gpio_signal signal); - -void motion_interrupt(enum gpio_signal signal); - -#endif /* !defined(__ASSEMBLER__) */ - -#endif /* __CROS_EC_BOARD_H */ diff --git a/board/wormdingler/build.mk b/board/wormdingler/build.mk deleted file mode 100644 index 74b6b95e4d..0000000000 --- a/board/wormdingler/build.mk +++ /dev/null @@ -1,14 +0,0 @@ -# -*- makefile -*- -# Copyright 2021 The Chromium OS Authors. All rights reserved. -# Use of this source code is governed by a BSD-style license that can be -# found in the LICENSE file. -# -# Board specific files build -# - -CHIP:=npcx -CHIP_FAMILY:=npcx7 -CHIP_VARIANT:=npcx7m6fc -BASEBOARD:=trogdor - -board-y=battery.o board.o led.o base_detect.o diff --git a/board/wormdingler/ec.tasklist b/board/wormdingler/ec.tasklist deleted file mode 100644 index ea2aaa97f5..0000000000 --- a/board/wormdingler/ec.tasklist +++ /dev/null @@ -1,22 +0,0 @@ -/* Copyright 2021 The Chromium OS Authors. All rights reserved. - * Use of this source code is governed by a BSD-style license that can be - * found in the LICENSE file. - */ - -/* - * See CONFIG_TASK_LIST in config.h for details. - */ - -#define CONFIG_TASK_LIST \ - TASK_ALWAYS(HOOKS, hook_task, NULL, ULTRA_TASK_STACK_SIZE) \ - TASK_ALWAYS(USB_CHG_P0, usb_charger_task, NULL, LARGER_TASK_STACK_SIZE) \ - TASK_ALWAYS(USB_CHG_P1, usb_charger_task, NULL, LARGER_TASK_STACK_SIZE) \ - TASK_NOTEST(CHIPSET, chipset_task, NULL, ULTRA_TASK_STACK_SIZE) \ - TASK_ALWAYS(CHARGER, charger_task, NULL, ULTRA_TASK_STACK_SIZE) \ - TASK_ALWAYS(MOTIONSENSE, motion_sense_task, NULL, VENTI_TASK_STACK_SIZE) \ - TASK_ALWAYS(HOSTCMD, host_command_task, NULL, ULTRA_TASK_STACK_SIZE) \ - TASK_ALWAYS(CONSOLE, console_task, NULL, ULTRA_TASK_STACK_SIZE) \ - TASK_ALWAYS(PD_C0, pd_task, NULL, ULTRA_TASK_STACK_SIZE) \ - TASK_ALWAYS(PD_C1, pd_task, NULL, ULTRA_TASK_STACK_SIZE) \ - TASK_ALWAYS(PD_INT_C0, pd_interrupt_handler_task, 0, ULTRA_TASK_STACK_SIZE) \ - TASK_ALWAYS(PD_INT_C1, pd_interrupt_handler_task, 1, ULTRA_TASK_STACK_SIZE) diff --git a/board/wormdingler/gpio.inc b/board/wormdingler/gpio.inc deleted file mode 100644 index 77a69a5faa..0000000000 --- a/board/wormdingler/gpio.inc +++ /dev/null @@ -1,196 +0,0 @@ -/* -*- mode:c -*- - * - * Copyright 2021 The Chromium OS Authors. All rights reserved. - * Use of this source code is governed by a BSD-style license that can be - * found in the LICENSE file. - */ - -/* Declare symbolic names for all the GPIOs that we care about. - * Note: Those with interrupt handlers must be declared first. */ - -/* USB-C interrupts */ -GPIO_INT(USB_C0_PD_INT_ODL, PIN(E, 0), GPIO_INT_FALLING, tcpc_alert_event) /* Interrupt from port-0 TCPC */ -GPIO_INT(USB_C1_PD_INT_ODL, PIN(F, 5), GPIO_INT_FALLING, tcpc_alert_event) /* Interrupt from port-1 TCPC */ -GPIO_INT(USB_C0_SWCTL_INT_ODL, PIN(0, 3), GPIO_INT_FALLING, ppc_interrupt) /* Interrupt from port-0 PPC */ -GPIO_INT(USB_C1_SWCTL_INT_ODL, PIN(4, 0), GPIO_INT_FALLING, ppc_interrupt) /* Interrupt from port-1 PPC */ -GPIO_INT(USB_C0_BC12_INT_L, PIN(6, 1), GPIO_INT_FALLING | GPIO_PULL_UP, usb0_evt) /* Interrupt from port-0 BC1.2 */ -GPIO_INT(USB_C1_BC12_INT_L, PIN(8, 2), GPIO_INT_FALLING | GPIO_PULL_UP, usb1_evt) /* Interrupt from port-1 BC1.2 */ - -/* System interrupts */ -GPIO_INT(CHG_ACOK_OD, PIN(0, 0), GPIO_INT_BOTH, extpower_interrupt) /* ACOK */ -GPIO_INT(CCD_MODE_ODL, PIN(E, 3), GPIO_INT_FALLING, board_connect_c0_sbu) /* Case Closed Debug Mode */ -GPIO_INT(EC_PWR_BTN_ODL, PIN(0, 1), GPIO_INT_BOTH, power_button_interrupt) /* Power button */ -GPIO_INT(EC_VOLDN_BTN_ODL, PIN(7, 0), GPIO_INT_BOTH | GPIO_PULL_UP, button_interrupt) /* Volume Down button */ -GPIO_INT(EC_VOLUP_BTN_ODL, PIN(F, 2), GPIO_INT_BOTH | GPIO_PULL_UP, button_interrupt) /* Volume Up button */ -GPIO_INT(EC_FLASH_WP_ODL, PIN(A, 1), GPIO_INT_BOTH, switch_interrupt) /* Write protection */ -GPIO_INT(LID_OPEN_EC, PIN(D, 2), GPIO_INT_BOTH, lid_interrupt) /* Lid open */ -GPIO_INT(AP_RST_L, PIN(C, 1), GPIO_INT_BOTH | GPIO_SEL_1P8V, chipset_ap_rst_interrupt) /* PMIC to signal AP reset */ -GPIO_INT(PS_HOLD, PIN(A, 4), GPIO_INT_BOTH | GPIO_PULL_DOWN, power_signal_interrupt) /* Indicate when AP triggers reset/shutdown */ -GPIO_INT(AP_SUSPEND, PIN(5, 7), GPIO_INT_BOTH, power_signal_interrupt) /* Suspend signal from PMIC */ -GPIO_INT(DEPRECATED_AP_RST_REQ, PIN(C, 2), GPIO_INT_BOTH | GPIO_PULL_DOWN | GPIO_SEL_1P8V, power_signal_interrupt) /* Deprecated AP initiated reset indicator */ - -/* - * When switch-cap is off, the POWER_GOOD signal is floating. Need a pull-down - * to make it low. Overload the interrupt function chipset_warm_reset_interrupt - * for not only signalling power_signal_interrupt but also handling the logic - * of WARM_RESET_L which is pulled-up by the same rail of POWER_GOOD. - */ -GPIO_INT(POWER_GOOD, PIN(5, 4), GPIO_INT_BOTH | GPIO_PULL_DOWN, chipset_power_good_interrupt) /* SRC_PP1800_S10A from PMIC */ -GPIO_INT(WARM_RESET_L, PIN(F, 4), GPIO_INT_BOTH | GPIO_SEL_1P8V, chipset_warm_reset_interrupt) /* AP warm reset */ -GPIO_INT(AP_EC_SPI_CS_L, PIN(5, 3), GPIO_INT_FALLING | GPIO_PULL_DOWN, shi_cs_event) /* EC SPI Chip Select */ - -GPIO_INT(BASE_DET_L, PIN(3, 7), GPIO_INT_BOTH, base_detect_interrupt) /* Detachable base attached? */ - -/* Sensor interrupts */ -GPIO_INT(ACCEL_GYRO_INT_L, PIN(A, 0), GPIO_INT_FALLING, motion_interrupt) /* Accelerometer/gyro interrupt */ - -/* Switchcap, for LN9310, it is the interrupt line of LN9310. */ -GPIO_INT(LN9310_INT, PIN(E, 2), GPIO_INT_FALLING, switchcap_interrupt) - -/* - * EC_RST_ODL acts as a wake source from hibernate mode. However, it does not - * need to be an interrupt for normal EC operations. Simply set it an INPUT. - */ -GPIO(EC_RST_ODL, PIN(0, 2), GPIO_INPUT) /* EC reset */ -GPIO(EC_ENTERING_RW, PIN(E, 1), GPIO_OUT_LOW) /* Indicate when EC is entering RW code */ -GPIO(EC_BATT_PRES_ODL, PIN(E, 5), GPIO_INPUT) /* Battery Present */ - -/* PMIC/AP 1.8V */ -GPIO(PM845_RESIN_L, PIN(3, 2), GPIO_ODR_HIGH) /* PMIC reset trigger */ -GPIO(PMIC_KPD_PWR_ODL, PIN(D, 6), GPIO_ODR_HIGH) /* PMIC power button */ -GPIO(EC_INT_L, PIN(A, 2), GPIO_ODR_HIGH) /* Interrupt line between AP and EC */ -GPIO(QSIP_ON, PIN(5, 0), GPIO_OUT_LOW) /* Not used, for non-switchcap testing */ - -/* Power enables */ -GPIO(HIBERNATE_L, PIN(5, 2), GPIO_ODR_HIGH) /* EC hibernate */ -GPIO(SWITCHCAP_ON_L, PIN(D, 5), GPIO_ODR_HIGH) /* Enable switch cap */ -GPIO(EN_PP3300_A, PIN(A, 6), GPIO_OUT_LOW) /* Enable PP3300 */ -GPIO(EN_PP5000_A, PIN(6, 7), GPIO_OUT_LOW) /* Enable PP5000 */ -GPIO(EC_BL_DISABLE_L, PIN(B, 6), GPIO_OUT_LOW) /* Backlight disable signal from EC */ - -/* Base detection */ -GPIO(EN_BASE, PIN(0, 4), GPIO_OUT_LOW) /* Enable power to detachable base */ - -/* POGO */ -GPIO(POGO_VBUS_PRESENT, PIN(6, 2), GPIO_INPUT) /* POGO PIN */ - -/* USB-C */ -GPIO(USB_C0_PD_RST_L, PIN(F, 1), GPIO_ODR_HIGH) /* Port-0 TCPC chip reset, actaully Open-Drain */ -GPIO(USB_C1_PD_RST_L, PIN(E, 4), GPIO_ODR_HIGH) /* Port-1 TCPC chip reset, actually Open-Drain */ -GPIO(DP_MUX_OE_L, PIN(9, 6), GPIO_ODR_HIGH) /* DP mux enable, actually Open-Drain */ -GPIO(DP_MUX_SEL, PIN(4, 5), GPIO_OUT_LOW) /* DP mux selection: L:C0, H:C1 */ -GPIO(DP_HOT_PLUG_DET, PIN(9, 5), GPIO_OUT_LOW) /* DP HPD to AP */ - -/* LEDs */ -GPIO(EC_CHG_LED_R_C0, PIN(C, 3), GPIO_OUT_LOW) -GPIO(EC_CHG_LED_G_C0, PIN(C, 4), GPIO_OUT_LOW) - -/* - * SPI host interface - enable PDs by default. These will be made functional - * by the SHI driver when the AP powers up, and restored back to GPIO when - * the AP powers down. - */ -GPIO(AP_EC_SPI_MOSI, PIN(4, 6), GPIO_INPUT | GPIO_PULL_DOWN) -GPIO(AP_EC_SPI_MISO, PIN(4, 7), GPIO_INPUT | GPIO_PULL_DOWN) -GPIO(AP_EC_SPI_CLK, PIN(5, 5), GPIO_INPUT | GPIO_PULL_DOWN) - -/* PWM */ -GPIO(EDP_BKLTCTL, PIN(B, 7), GPIO_INPUT) /* PWM5 */ -GPIO(WCAM_EC_VSYNC, PIN(C, 0), GPIO_INPUT) /* PWM6 */ -GPIO(FCAM_EC_VSYNC, PIN(6, 0), GPIO_INPUT) /* PWM7 */ - -/* ADC */ -GPIO(PPVAR_BOOSTIN_SENSE, PIN(4, 4), GPIO_INPUT) /* ADC1 */ -GPIO(CHARGER_IADP, PIN(4, 3), GPIO_INPUT) /* ADC2 */ -GPIO(CHARGER_PMON, PIN(4, 2), GPIO_INPUT) /* ADC3 */ - -/* I2C */ -GPIO(EC_I2C_POWER_SCL, PIN(B, 5), GPIO_INPUT) -GPIO(EC_I2C_POWER_SDA, PIN(B, 4), GPIO_INPUT) -GPIO(EC_I2C_USB_C0_PD_SCL, PIN(9, 0), GPIO_INPUT) -GPIO(EC_I2C_USB_C0_PD_SDA, PIN(8, 7), GPIO_INPUT) -GPIO(EC_I2C_USB_C1_PD_SCL, PIN(9, 2), GPIO_INPUT) -GPIO(EC_I2C_USB_C1_PD_SDA, PIN(9, 1), GPIO_INPUT) -GPIO(EC_I2C_EEPROM_SCL, PIN(3, 3), GPIO_INPUT) -GPIO(EC_I2C_EEPROM_SDA, PIN(3, 6), GPIO_INPUT) -GPIO(EC_I2C_SENSOR_SCL, PIN(B, 3), GPIO_INPUT | GPIO_SEL_1P8V) -GPIO(EC_I2C_SENSOR_SDA, PIN(B, 2), GPIO_INPUT | GPIO_SEL_1P8V) - -/* Board/SKU IDs */ -GPIO(BRD_ID0, PIN(C, 7), GPIO_INPUT) -GPIO(BRD_ID1, PIN(9, 3), GPIO_INPUT) -GPIO(BRD_ID2, PIN(6, 3), GPIO_INPUT) -GPIO(SKU_ID0, PIN(F, 0), GPIO_INPUT) -GPIO(SKU_ID1, PIN(4, 1), GPIO_INPUT) -GPIO(SKU_ID2, PIN(D, 4), GPIO_INPUT) - -/* Special straps */ -GPIO(ARM_X86, PIN(6, 6), GPIO_OUT_LOW) /* NC, low for power saving */ - -/* Unused GPIOs, NC. Apply PU for power saving */ -UNUSED(PIN(5, 1)) -UNUSED(PIN(F, 3)) -UNUSED(PIN(3, 1)) -UNUSED(PIN(3, 0)) -UNUSED(PIN(2, 7)) -UNUSED(PIN(2, 6)) -UNUSED(PIN(2, 5)) -UNUSED(PIN(2, 4)) -UNUSED(PIN(2, 3)) -UNUSED(PIN(2, 2)) -UNUSED(PIN(2, 1)) -UNUSED(PIN(2, 0)) -UNUSED(PIN(1, 7)) -UNUSED(PIN(1, 6)) -UNUSED(PIN(1, 5)) -UNUSED(PIN(1, 4)) -UNUSED(PIN(1, 3)) -UNUSED(PIN(1, 2)) -UNUSED(PIN(1, 1)) -UNUSED(PIN(1, 0)) -UNUSED(PIN(0, 7)) -UNUSED(PIN(0, 6)) -UNUSED(PIN(0, 5)) -UNUSED(PIN(9, 4)) -UNUSED(PIN(9, 7)) -UNUSED(PIN(A, 7)) -UNUSED(PIN(B, 0)) -UNUSED(PIN(A, 5)) -UNUSED(PIN(3, 5)) -UNUSED(PIN(7, 2)) -UNUSED(PIN(8, 1)) -UNUSED(PIN(7, 6)) -UNUSED(PIN(3, 4)) -UNUSED(PIN(C, 5)) -UNUSED(PIN(C, 6)) -UNUSED(PIN(A, 3)) -UNUSED(PIN(8, 3)) -UNUSED(PIN(B, 1)) -UNUSED(PIN(5, 6)) -UNUSED(PIN(8, 0)) -UNUSED(PIN(D, 0)) -UNUSED(PIN(D, 1)) -UNUSED(PIN(D, 3)) -UNUSED(PIN(7, 5)) -UNUSED(PIN(8, 6)) -UNUSED(PIN(7, 3)) -UNUSED(PIN(7, 4)) -UNUSED(PIN(D, 7)) -UNUSED(PIN(8, 5)) - -/* Alternate functions GPIO definitions */ -ALTERNATE(PIN_MASK(6, 0x30), 0, MODULE_UART, 0) /* UART (GPIO64/65) */ -ALTERNATE(PIN_MASK(B, 0x30), 1, MODULE_I2C, 0) /* I2C0 (GPIOB4/B5) */ -ALTERNATE(PIN_MASK(9, 0x07), 1, MODULE_I2C, 0) /* I2C1 SDA (GPIO90), I2C2 (GPIO91/92) */ -ALTERNATE(PIN_MASK(8, 0x80), 1, MODULE_I2C, 0) /* I2C1 SCL (GPIO87) */ -ALTERNATE(PIN_MASK(3, 0x48), 1, MODULE_I2C, 0) /* I2C5 (GPIO33/36) */ -ALTERNATE(PIN_MASK(B, 0x0C), 1, MODULE_I2C, GPIO_SEL_1P8V) /* I2C7 (GPIOB2/B3) - 1.8V */ -ALTERNATE(PIN_MASK(4, 0x1C), 0, MODULE_ADC, 0) /* ADC1 (GPIO44), ADC2 (GPIO43), ADC3 (GPIO42) */ -ALTERNATE(PIN_MASK(4, 0xC0), 1, MODULE_SPI, GPIO_SEL_1P8V) /* SHI_SDO (GPIO47), SHI_SDI (GPIO46) */ -ALTERNATE(PIN_MASK(5, 0x28), 1, MODULE_SPI, GPIO_SEL_1P8V) /* SHI_SCLK (GPIO55), SHI_CS# (GPIO53) */ -ALTERNATE(PIN_MASK(B, 0x80), 1, MODULE_PWM, 0) /* PWM5 (GPIOB7) - EDP_BKLTCTL */ -/* TODO(Camera?) should have a poper config for this, PWM or not */ -ALTERNATE(PIN_MASK(C, 0x01), 1, MODULE_PWM, 0) /* PWM6 (GPIOC0) - WCAM_EC_VSYNC */ -ALTERNATE(PIN_MASK(6, 0x01), 1, MODULE_PWM, 0) /* PWM7 (GPIO60) - FCAM_EC_VSYNC */ - - diff --git a/board/wormdingler/led.c b/board/wormdingler/led.c deleted file mode 100644 index 40de6257fa..0000000000 --- a/board/wormdingler/led.c +++ /dev/null @@ -1,164 +0,0 @@ -/* Copyright 2021 The Chromium OS Authors. All rights reserved. - * Use of this source code is governed by a BSD-style license that can be - * found in the LICENSE file. - * - * Power and battery LED control. - */ - -#include "battery.h" -#include "charge_manager.h" -#include "charge_state.h" -#include "chipset.h" -#include "ec_commands.h" -#include "gpio.h" -#include "hooks.h" -#include "host_command.h" -#include "led_common.h" -#include "system.h" -#include "util.h" -#include "extpower.h" - -#define LED_ONE_SEC (1000 / HOOK_TICK_INTERVAL_MS) -/* Battery LED blinks every per 400ms */ -#define LED_HALF_ONE_SEC (500 / HOOK_TICK_INTERVAL_MS) - -#define BAT_LED_ON 1 -#define BAT_LED_OFF 0 - -const enum ec_led_id supported_led_ids[] = { - EC_LED_ID_BATTERY_LED, -}; - -const int supported_led_ids_count = ARRAY_SIZE(supported_led_ids); - -enum led_color { - LED_OFF = 0, - LED_RED, - LED_GREEN, - LED_AMBER, - LED_COLOR_COUNT /* Number of colors, not a color itself */ -}; - -static void led_set_color(enum led_color color) -{ - gpio_set_level(GPIO_EC_CHG_LED_R_C0, - (color == LED_RED) ? BAT_LED_ON : BAT_LED_OFF); - gpio_set_level(GPIO_EC_CHG_LED_G_C0, - (color == LED_GREEN) ? BAT_LED_ON : BAT_LED_OFF); - if (color == LED_AMBER) { - gpio_set_level(GPIO_EC_CHG_LED_R_C0, BAT_LED_ON); - gpio_set_level(GPIO_EC_CHG_LED_G_C0, BAT_LED_ON); - } -} - -void led_get_brightness_range(enum ec_led_id led_id, uint8_t *brightness_range) -{ - brightness_range[EC_LED_COLOR_RED] = 1; - brightness_range[EC_LED_COLOR_GREEN] = 1; - brightness_range[EC_LED_COLOR_AMBER] = 1; -} - -int led_set_brightness(enum ec_led_id led_id, const uint8_t *brightness) -{ - if (brightness[EC_LED_COLOR_RED] != 0) - led_set_color(LED_RED); - else if (brightness[EC_LED_COLOR_GREEN] != 0) - led_set_color(LED_GREEN); - else if (brightness[EC_LED_COLOR_AMBER] != 0) - led_set_color(LED_AMBER); - else - led_set_color(LED_OFF); - - return EC_SUCCESS; -} - -static void board_led_set_battery(void) -{ - static int battery_ticks; - int color = LED_OFF; - int period = 0; - int percent = DIV_ROUND_NEAREST(charge_get_display_charge(), 10); - uint32_t chflags = charge_get_flags(); - - battery_ticks++; - - switch (charge_get_state()) { - case PWR_STATE_CHARGE: - case PWR_STATE_CHARGE_NEAR_FULL: - if (chipset_in_state(CHIPSET_STATE_ON | - CHIPSET_STATE_ANY_SUSPEND | - CHIPSET_STATE_ANY_OFF)) { - if (percent <= BATTERY_LEVEL_CRITICAL) { - /* battery capa <= 5%, Red */ - color = LED_RED; - } else if (percent > BATTERY_LEVEL_CRITICAL && - percent < BATTERY_LEVEL_NEAR_FULL) { - /* 5% < battery capa < 97%, Orange */ - color = LED_AMBER; - } else { - /* battery capa >= 97%, Green */ - color = LED_GREEN; - } - } - break; - case PWR_STATE_DISCHARGE: - /* Always indicate off on when discharging */ - color = LED_OFF; - break; - case PWR_STATE_ERROR: - /* Battery error, Red on 1sec off 1sec */ - period = (1 + 1) * LED_ONE_SEC; - battery_ticks = battery_ticks % period; - if (battery_ticks < 1 * LED_ONE_SEC) - color = LED_RED; - else - color = LED_OFF; - break; - case PWR_STATE_IDLE: /* External power connected in IDLE */ - if (chflags & CHARGE_FLAG_FORCE_IDLE) { - /* Factory mode, Red 2 sec, green 2 sec */ - period = (2 + 2) * LED_ONE_SEC; - battery_ticks = battery_ticks % period; - if (battery_ticks < 2 * LED_ONE_SEC) - color = LED_RED; - else - color = LED_GREEN; - } else - color = LED_RED; - break; - default: - /* Other states don't alter LED behavior */ - break; - } - - led_set_color(color); -} - -/* Called by hook task every TICK */ -static void led_tick(void) -{ - if (led_auto_control_is_enabled(EC_LED_ID_BATTERY_LED)) - board_led_set_battery(); -} -DECLARE_HOOK(HOOK_TICK, led_tick, HOOK_PRIO_DEFAULT); - -void led_control(enum ec_led_id led_id, enum ec_led_state state) -{ - enum led_color color; - - if ((led_id != EC_LED_ID_RECOVERY_HW_REINIT_LED) && - (led_id != EC_LED_ID_SYSRQ_DEBUG_LED)) - return; - - if (state == LED_STATE_RESET) { - led_auto_control(EC_LED_ID_BATTERY_LED, 1); - board_led_set_battery(); - return; - } - - color = state ? LED_RED : LED_OFF; - - led_auto_control(EC_LED_ID_BATTERY_LED, 0); - - led_set_color(color); -} diff --git a/board/wormdingler/vif_override.xml b/board/wormdingler/vif_override.xml deleted file mode 100644 index 32736caf64..0000000000 --- a/board/wormdingler/vif_override.xml +++ /dev/null @@ -1,3 +0,0 @@ -<!-- Add VIF field overrides here. See genvif.c and the Vendor Info File - Definition from the USB-IF. ---> |