1 files changed, 0 insertions, 152 deletions
diff --git a/chip/lm4/peci.c b/chip/lm4/peci.c
deleted file mode 100644
index b3b54a64bc..0000000000
--- a/chip/lm4/peci.c
+++ /dev/null
@@ -1,152 +0,0 @@
-/* Copyright 2012 The Chromium OS Authors. All rights reserved.
- * Use of this source code is governed by a BSD-style license that can be
- * found in the LICENSE file.
- */
-
-/* PECI interface for Chrome EC */
-
-#include "chipset.h"
-#include "clock.h"
-#include "common.h"
-#include "console.h"
-#include "gpio.h"
-#include "hooks.h"
-#include "peci.h"
-#include "registers.h"
-#include "temp_sensor.h"
-#include "util.h"
-
-/* Initial PECI baud rate */
-#define PECI_BAUD_RATE 100000
-
-/* Polling interval for PECI, in ms */
-#define PECI_POLL_INTERVAL_MS 250
-
-/*
- * Internal and external path delays, in ns.  The external delay is a
- * best-guess measurement, but we're fairly tolerant of a bad guess because
- * PECI_BAUD_RATE is slow compared to PECI's actual maximum baud rate.
- */
-#define PECI_TD_FET_NS 60
-#define PECI_TD_INT_NS 80
-
-/* Number of controller retries. Should be between 0 and 7. */
-#define PECI_RETRY_COUNT 4
-
-/* Timing negotiation error bypass. 1 = on. 0 = off. */
-#define PECI_ERROR_BYPASS 1
-
-#define TEMP_AVG_LENGTH 4  /* Should be power of 2 */
-static int temp_vals[TEMP_AVG_LENGTH];
-static int temp_idx;
-
-int peci_get_cpu_temp(void)
-{
-	int v = LM4_PECI_M0D0 & 0xffff;
-
-	if (v >= 0x8000 && v <= 0x8fff)
-		return -1;
-
-	return v >> 6;
-}
-
-int peci_temp_sensor_get_val(int idx, int *temp_ptr)
-{
-	int sum = 0;
-	int success_cnt = 0;
-	int i;
-
-	if (!chipset_in_state(CHIPSET_STATE_ON))
-		return EC_ERROR_NOT_POWERED;
-
-	for (i = 0; i < TEMP_AVG_LENGTH; ++i) {
-		if (temp_vals[i] >= 0) {
-			success_cnt++;
-			sum += temp_vals[i];
-		}
-	}
-
-	/*
-	 * Require at least two valid samples. When the AP transitions into S0,
-	 * it is possible, depending on the timing of the PECI sample, to read
-	 * an invalid temperature. This is very rare, but when it does happen
-	 * the temperature returned is CONFIG_PECI_TJMAX. Requiring two valid
-	 * samples here assures us that one bad maximum temperature reading
-	 * when entering S0 won't cause us to trigger an over temperature.
-	 */
-	if (success_cnt < 2)
-		return EC_ERROR_UNKNOWN;
-
-	*temp_ptr = sum / success_cnt;
-	return EC_SUCCESS;
-}
-
-static void peci_temp_sensor_poll(void)
-{
-	temp_vals[temp_idx] = peci_get_cpu_temp();
-	temp_idx = (temp_idx + 1) & (TEMP_AVG_LENGTH - 1);
-}
-DECLARE_HOOK(HOOK_TICK, peci_temp_sensor_poll, HOOK_PRIO_TEMP_SENSOR);
-
-static void peci_freq_changed(void)
-{
-	int freq = clock_get_freq();
-	int baud;
-
-	/* Disable polling while reconfiguring */
-	LM4_PECI_CTL = 0;
-
-	/*
-	 * Calculate baud setting from desired rate, compensating for internal
-	 * and external delays.
-	 */
-	baud = freq / (4 * PECI_BAUD_RATE) - 2;
-	baud -= (freq / 1000000) * (PECI_TD_FET_NS + PECI_TD_INT_NS) / 1000;
-
-	/* Set baud rate and polling rate */
-	LM4_PECI_DIV = (baud << 16) |
-		(PECI_POLL_INTERVAL_MS * (freq / 1000 / 4096));
-
-	/* Set up temperature monitoring to report in degrees K */
-	LM4_PECI_CTL = ((CONFIG_PECI_TJMAX + 273) << 22) | 0x0001 |
-		       (PECI_RETRY_COUNT << 12) |
-		       (PECI_ERROR_BYPASS << 11);
-}
-DECLARE_HOOK(HOOK_FREQ_CHANGE, peci_freq_changed, HOOK_PRIO_DEFAULT);
-
-static void peci_init(void)
-{
-	int i;
-
-	/* Enable the PECI module in run and sleep modes. */
-	clock_enable_peripheral(CGC_OFFSET_PECI, 0x1,
-			CGC_MODE_RUN | CGC_MODE_SLEEP);
-
-	/* Configure GPIOs */
-	gpio_config_module(MODULE_PECI, 1);
-
-	/* Set initial clock frequency */
-	peci_freq_changed();
-
-	/* Initialize temperature reading buffer to a valid value. */
-	for (i = 0; i < TEMP_AVG_LENGTH; ++i)
-		temp_vals[i] = 300; /* 27 C */
-}
-DECLARE_HOOK(HOOK_INIT, peci_init, HOOK_PRIO_DEFAULT);
-
-/*****************************************************************************/
-/* Console commands */
-
-static int command_peci_temp(int argc, char **argv)
-{
-	int t = peci_get_cpu_temp();
-	if (t == -1) {
-		ccprintf("PECI error 0x%04x\n", LM4_PECI_M0D0 & 0xffff);
-		return EC_ERROR_UNKNOWN;
-	}
-	ccprintf("CPU temp = %d K = %d C\n", t, K_TO_C(t));
-	return EC_SUCCESS;
-}
-DECLARE_CONSOLE_COMMAND(pecitemp, command_peci_temp,
-			NULL,
-			"Print CPU temperature");