1 files changed, 0 insertions, 92 deletions
diff --git a/chip/npcx/build.mk b/chip/npcx/build.mk
deleted file mode 100644
index 4be1b2994f..0000000000
--- a/chip/npcx/build.mk
+++ /dev/null
@@ -1,92 +0,0 @@
-# -*- makefile -*-
-# Copyright 2014 The Chromium OS Authors. All rights reserved.
-# Use of this source code is governed by a BSD-style license that can be
-# found in the LICENSE file.
-#
-# NPCX chip specific files build
-#
-
-# NPCX SoC has a Cortex-M4F ARM core
-CORE:=cortex-m
-# Allow the full Cortex-M4 instruction set
-CFLAGS_CPU+=-march=armv7e-m -mcpu=cortex-m4
-
-# Assign default CHIP_FAMILY as npcx5 for old boards used npcx5 series
-ifeq ($(CHIP_FAMILY),)
-CHIP_FAMILY:=npcx5
-endif
-
-# Required chip modules
-chip-y=header.o clock.o gpio.o hwtimer.o system.o uart.o uartn.o sib.o
-chip-y+=system-$(CHIP_FAMILY).o
-chip-y+=gpio-$(CHIP_FAMILY).o
-
-# Optional chip modules
-chip-$(CONFIG_ADC)+=adc.o
-chip-$(CONFIG_AUDIO_CODEC)+=apm.o wov.o
-chip-$(CONFIG_AUDIO_CODEC_DMIC)+=audio_codec_dmic.o
-chip-$(CONFIG_AUDIO_CODEC_I2S_RX)+=audio_codec_i2s_rx.o
-chip-$(CONFIG_FANS)+=fan.o
-chip-$(CONFIG_FLASH_PHYSICAL)+=flash.o
-chip-$(CONFIG_I2C)+=i2c.o i2c-$(CHIP_FAMILY).o
-chip-$(CONFIG_HOSTCMD_X86)+=lpc.o
-chip-$(CONFIG_HOSTCMD_ESPI)+=espi.o
-chip-$(CONFIG_PECI)+=peci.o
-chip-$(CONFIG_HOSTCMD_SHI)+=shi.o
-chip-$(CONFIG_CEC)+=cec.o
-# pwm functions are implemented with the fan functions
-chip-$(CONFIG_PWM)+=pwm.o
-chip-$(CONFIG_SPI)+=spi.o
-chip-$(CONFIG_WATCHDOG)+=watchdog.o
-ifndef CONFIG_KEYBOARD_NOT_RAW
-chip-$(HAS_TASK_KEYSCAN)+=keyboard_raw.o
-endif
-
-chip-$(CONFIG_PS2)+=ps2.o
-# Only npcx9 or later chip family can support LCT module
-ifneq ($(CHIP_FAMILY),$(filter $(CHIP_FAMILY),npcx5 npcx7))
-chip-y+=lct.o
-endif
-
-chip-$(CONFIG_SHA256_HW_ACCELERATE)+=sha256_chip.o
-
-# spi monitor program fw for openocd and UUT(UART Update Tool)
-npcx-monitor-fw=chip/npcx/spiflashfw/npcx_monitor
-npcx-monitor-fw-bin=${out}/$(npcx-monitor-fw).bin
-PROJECT_EXTRA+=${npcx-monitor-fw-bin}
-# Monitor header is only used for UUT which is not supported on npcx5.
-ifneq "$(CHIP_FAMILY)" "npcx5"
-npcx-monitor-hdr=chip/npcx/spiflashfw/monitor_hdr
-npcx-monitor-hdr-ro-bin=${out}/$(npcx-monitor-hdr)_ro.bin
-npcx-monitor-hdr-rw-bin=${out}/$(npcx-monitor-hdr)_rw.bin
-PROJECT_EXTRA+=${npcx-monitor-hdr-ro-bin} ${npcx-monitor-hdr-rw-bin}
-endif
-
-# ECST tool is for filling the header used by booter of npcx EC
-show_esct_cmd=$(if $(V),,echo '  ECST   ' $(subst $(out)/,,$@) ; )
-
-# Get the firmware length from the mapfile.  This can differ from the file
-# size when the CONFIG_CHIP_INIT_ROM_REGION is used. Note that the -fwlen
-# parameter for the ecst utility must be in hex.
-cmd_fwlen=$(shell awk '\
-  /__flash_used =/ {flash_used = strtonum($$1)} \
-  END {printf ("%x", flash_used)}' $(1))
-
-# ECST options for header
-bld_ecst=${out}/util/ecst -chip $(CHIP_VARIANT) \
-	-usearmrst -mode bt -ph -i $(1) -o $(2) -nohcrc -nofcrc -flashsize 8 \
-	-fwlen $(call cmd_fwlen, $(patsubst %.flat,%.map,$(2))) \
-	-spimaxclk 50 -spireadmode dual 1> /dev/null
-
-# Replace original one with the flat file including header
-moveflat=mv -f $(1) $(2)
-
-# Commands for ECST
-cmd_ecst=$(show_esct_cmd)$(call moveflat,$@,$@.tmp);$(call bld_ecst,$@.tmp,$@)
-
-# Commands to append npcx header in ec.RO.flat
-cmd_org_ec_elf_to_flat = $(OBJCOPY) --set-section-flags .roshared=share \
-                         -O binary $(patsubst %.flat,%.elf,$@) $@
-cmd_npcx_ro_elf_to_flat=$(cmd_org_ec_elf_to_flat);$(cmd_ecst)
-cmd_ec_elf_to_flat = $(if $(filter $(out)/RO/ec.RO.flat, $@), \
-                     $(cmd_npcx_ro_elf_to_flat), $(cmd_org_ec_elf_to_flat) )