1 files changed, 0 insertions, 87 deletions
diff --git a/docs/configuration/keyboard.md b/docs/configuration/keyboard.md
deleted file mode 100644
index 8398fefbde..0000000000
--- a/docs/configuration/keyboard.md
+++ /dev/null
@@ -1,87 +0,0 @@
-## Configure Keyboard
-
-## Config options
-
-Keyboard options start with `CONFIG_KEYBOARD*`. Evaluate whether each option is
-appropriate to add to `baseboard.h` or `board.h`.
-
-Your board should select only one of these options to configure the protocol
-used to send keyboard events to the AP.
-
--   `CONFIG_KEYBOARD_PROTOCOL_8042` - Systems with an x86 AP use the 8042
-    protocol.
--   `CONFIG_KEYBOARD_PROTOCOL_MKBP` - Systems without an x86 AP (e.g. ARM)
-    typically use the MKBP protocol.
-
-## Feature Parameters
-
--   `CONFIG_KEYBOARD_KSO_BASE <pin>` - Evaluate whether this parameter is
-    required by your board.
-
-## GPIOs and Alternate Pins
-
-Define `ALTERNATE()` pin entries for all keyboard matrix signals, to connect the
-signals to the keyboard controller of the EC chipset.
-
-Note that KSO_02 is purposely not configured for for alternate mode. See the
-[H1 Special Requirements](#H1-Special-Requirements) below for details.
-
-```c
-/* Example Keyboard pin setup */
-#define GPIO_KB_INPUT (GPIO_INPUT | GPIO_PULL_UP)
-ALTERNATE(PIN_MASK(3, 0x03), 0, MODULE_KEYBOARD_SCAN, GPIO_KB_INPUT) /* KSI_00-01 */
-ALTERNATE(PIN_MASK(2, 0xFC), 0, MODULE_KEYBOARD_SCAN, GPIO_KB_INPUT) /* KSI_02-07 */
-ALTERNATE(PIN_MASK(2, 0x03), 0, MODULE_KEYBOARD_SCAN, GPIO_ODR_HIGH) /* KSO_00-01 */
-ALTERNATE(PIN_MASK(1, 0x7F), 0, MODULE_KEYBOARD_SCAN, GPIO_ODR_HIGH) /* KSO_03-09 */
-ALTERNATE(PIN_MASK(0, 0xF0), 0, MODULE_KEYBOARD_SCAN, GPIO_ODR_HIGH) /* KSO_10-13 */
-ALTERNATE(PIN_MASK(8, 0x04), 0, MODULE_KEYBOARD_SCAN, GPIO_ODR_HIGH) /* KSO_14    */
-```
-
-See the [GPIO](./gpio.md) documentation for additional details on the GPIO
-macros.
-
-## Data structures
-
--   `struct keyboard_scan_config keyscan_config` - This can be used to customize
-    the keyboard scanner (e.g. scan frequency, debounce duration, etc.).
-
-## Tasks
-
-The `KEYSCAN` task monitors the keyboard matrix for new key presses and is
-required by this feature. The priority is set as one of the highest priority
-tasks in the system, typically only below the `PD_Cn` and `PD_INT_Cn` tasks.
-
-```c
-    TASK_NOTEST(KEYSCAN, keyboard_scan_task, NULL, TASK_STACK_SIZE) \
-```
-
-The `KEYPROTO` task handles sending and receiving 8042 protocol messages from
-the AP and is required when `CONFIG_KEYBOARD_PROTOCOL_8042` is used. The typical
-priority is lower than the `HOSTCMD` task.
-
-```c
-    TASK_NOTEST(KEYPROTO, keyboard_protocol_task, NULL, TASK_STACK_SIZE) \
-```
-
-## Additional Notes
-
--   If you're including keyboard support, you should also define
-    `CONFIG_CMD_KEYBOARD` to enable keyboard debug commands from the EC console.
--   `CONFIG_KEYBOARD_PROTOCOL_MKBP` automatically enables `CONFIG_MKBP_EVENT`.
--   Boards that enable `CONFIG_KEYBOARD_PROTOCOL_8042` will often also define
-    `CONFIG_MKBP_EVENT` for sensor events. In this case only motion sensor data
-    is reported using the MKBP protocol, keyboard events are provided using the
-    8042 protocol. Refer to [Configuring Sensors](./motion_sensors.md) for more
-    information.
-
-### H1 Special Requirements
-
-On Boards that use the H1 secure microcontroller, one KSI (keyboard scan input)
-signal and one KSO (keyboard scan output) signal are routed through the H1
-microcontroller. There are additional GPIO and configuration options that must
-be enabled in this case. - The KSO_02/COL2 signal is always inverted. Explicitly
-configure the GPIO to default low. `c GPIO(KBD_KSO2, PIN(1, 7), GPIO_OUT_LOW) /*
-KSO_02 inverted */` - Add the define `CONFIG_KEYBOARD_COL2_INVERTED` to
-`baseboard.h` or `board.h`. - If required by the board, define one of the
-following options to configure the KSI pin routed to the H1 microcontroller. -
-`CONFIG_KEYBOARD_PWRBTN_ASSERTS_KSI2` - `CONFIG_KEYBOARD_PWRBTN_ASSERTS_KSI3`