diff options
Diffstat (limited to 'zephyr/projects/herobrine/src/usbc_config.c')
-rw-r--r-- | zephyr/projects/herobrine/src/usbc_config.c | 278 |
1 files changed, 278 insertions, 0 deletions
diff --git a/zephyr/projects/herobrine/src/usbc_config.c b/zephyr/projects/herobrine/src/usbc_config.c new file mode 100644 index 0000000000..f040ab12cb --- /dev/null +++ b/zephyr/projects/herobrine/src/usbc_config.c @@ -0,0 +1,278 @@ +/* Copyright 2021 The ChromiumOS Authors + * Use of this source code is governed by a BSD-style license that can be + * found in the LICENSE file. + */ + +/* Herobrine board-specific USB-C configuration */ + +#include <zephyr/drivers/gpio.h> + +#include "charger.h" +#include "charger/isl923x_public.h" +#include "charge_manager.h" +#include "charge_state.h" +#include "common.h" +#include "config.h" +#include "cros_board_info.h" +#include "gpio/gpio_int.h" +#include "hooks.h" +#include "ppc/sn5s330_public.h" +#include "ppc/syv682x_public.h" +#include "system.h" +#include "tcpm/ps8xxx_public.h" +#include "tcpm/tcpci.h" +#include "timer.h" +#include "usb_pd.h" +#include "usb_mux.h" +#include "usbc_ocp.h" +#include "usbc_ppc.h" +#include "usbc/ppc.h" + +#define CPRINTS(format, args...) cprints(CC_USBCHARGE, format, ##args) +#define CPRINTF(format, args...) cprintf(CC_USBCHARGE, format, ##args) + +/* GPIO Interrupt Handlers */ +void tcpc_alert_event(enum gpio_signal signal) +{ + int port = -1; + + switch (signal) { + case GPIO_USB_C0_PD_INT_ODL: + port = 0; + break; + case GPIO_USB_C1_PD_INT_ODL: + port = 1; + break; + default: + return; + } + + schedule_deferred_pd_interrupt(port); +} + +static void usba_oc_deferred(void) +{ + /* Use next number after all USB-C ports to indicate the USB-A port */ + board_overcurrent_event( + CONFIG_USB_PD_PORT_MAX_COUNT, + !gpio_pin_get_dt(GPIO_DT_FROM_NODELABEL(gpio_usb_a0_oc_odl))); +} +DECLARE_DEFERRED(usba_oc_deferred); + +void usba_oc_interrupt(enum gpio_signal signal) +{ + hook_call_deferred(&usba_oc_deferred_data, 0); +} + +void ppc_interrupt(enum gpio_signal signal) +{ + switch (signal) { + case GPIO_USB_C0_SWCTL_INT_ODL: + ppc_chips[0].drv->interrupt(0); + break; + + case GPIO_USB_C1_SWCTL_INT_ODL: + ppc_chips[1].drv->interrupt(1); + break; + + default: + break; + } +} + +int charger_profile_override(struct charge_state_data *curr) +{ + int usb_mv; + int port; + + if (curr->state != ST_CHARGE) + return 0; + + /* Lower the max requested voltage to 5V when battery is full. */ + if (chipset_in_state(CHIPSET_STATE_ANY_OFF) && + !(curr->batt.flags & BATT_FLAG_BAD_STATUS) && + !(curr->batt.flags & BATT_FLAG_WANT_CHARGE) && + (curr->batt.status & STATUS_FULLY_CHARGED)) + usb_mv = 5000; + else + usb_mv = PD_MAX_VOLTAGE_MV; + + if (pd_get_max_voltage() != usb_mv) { + CPRINTS("VBUS limited to %dmV", usb_mv); + for (port = 0; port < CONFIG_USB_PD_PORT_MAX_COUNT; port++) + pd_set_external_voltage_limit(port, usb_mv); + } + + return 0; +} + +enum ec_status charger_profile_override_get_param(uint32_t param, + uint32_t *value) +{ + return EC_RES_INVALID_PARAM; +} + +enum ec_status charger_profile_override_set_param(uint32_t param, + uint32_t value) +{ + return EC_RES_INVALID_PARAM; +} + +/* Initialize board USC-C things */ +static void board_init_usbc(void) +{ + /* Enable USB-A overcurrent interrupt */ + gpio_enable_dt_interrupt(GPIO_INT_FROM_NODELABEL(int_usb_a0_oc)); +} +DECLARE_HOOK(HOOK_INIT, board_init_usbc, HOOK_PRIO_DEFAULT); + +void board_tcpc_init(void) +{ + /* Only reset TCPC if not sysjump */ + if (!system_jumped_late()) { + /* TODO(crosbug.com/p/61098): How long do we need to wait? */ + board_reset_pd_mcu(); + } + + /* Enable PPC interrupts */ + gpio_enable_dt_interrupt(GPIO_INT_FROM_NODELABEL(int_usb_c0_swctl)); + + /* Enable TCPC interrupts */ + gpio_enable_dt_interrupt(GPIO_INT_FROM_NODELABEL(int_usb_c0_pd)); + gpio_enable_dt_interrupt(GPIO_INT_FROM_NODELABEL(int_usb_c1_pd)); + + /* + * Initialize HPD to low; after sysjump SOC needs to see + * HPD pulse to enable video path + */ + for (int port = 0; port < CONFIG_USB_PD_PORT_MAX_COUNT; ++port) + usb_mux_hpd_update(port, USB_PD_MUX_HPD_LVL_DEASSERTED | + USB_PD_MUX_HPD_IRQ_DEASSERTED); +} +DECLARE_HOOK(HOOK_INIT, board_tcpc_init, HOOK_PRIO_POST_I2C); + +void board_reset_pd_mcu(void) +{ + cprints(CC_USB, "Resetting TCPCs..."); + cflush(); + + gpio_pin_set_dt(GPIO_DT_FROM_NODELABEL(gpio_usb_c0_pd_rst_l), 0); + gpio_pin_set_dt(GPIO_DT_FROM_NODELABEL(gpio_usb_c1_pd_rst_l), 0); + msleep(PS8XXX_RESET_DELAY_MS); + gpio_pin_set_dt(GPIO_DT_FROM_NODELABEL(gpio_usb_c0_pd_rst_l), 1); + gpio_pin_set_dt(GPIO_DT_FROM_NODELABEL(gpio_usb_c1_pd_rst_l), 1); + msleep(PS8805_FW_INIT_DELAY_MS); +} + +void board_set_tcpc_power_mode(int port, int mode) +{ + /* Ignore the "mode" to turn the chip on. We can only do a reset. */ + if (mode) + return; + + board_reset_pd_mcu(); +} + +int board_vbus_sink_enable(int port, int enable) +{ + /* Both ports are controlled by PPC SN5S330 */ + return ppc_vbus_sink_enable(port, enable); +} + +int board_is_sourcing_vbus(int port) +{ + /* Both ports are controlled by PPC SN5S330 */ + return ppc_is_sourcing_vbus(port); +} + +void board_overcurrent_event(int port, int is_overcurrented) +{ + /* TODO(b/120231371): Notify AP */ + CPRINTS("p%d: overcurrent!", port); +} + +int board_set_active_charge_port(int port) +{ + int is_real_port = (port >= 0 && port < CONFIG_USB_PD_PORT_MAX_COUNT); + int i; + + if (!is_real_port && port != CHARGE_PORT_NONE) + return EC_ERROR_INVAL; + + if (port == CHARGE_PORT_NONE) { + CPRINTS("Disabling all charging port"); + + /* Disable all ports. */ + for (i = 0; i < CONFIG_USB_PD_PORT_MAX_COUNT; i++) { + /* + * Do not return early if one fails otherwise we can + * get into a boot loop assertion failure. + */ + if (board_vbus_sink_enable(i, 0)) + CPRINTS("Disabling p%d sink path failed.", i); + } + + return EC_SUCCESS; + } + + /* Check if the port is sourcing VBUS. */ + if (board_is_sourcing_vbus(port)) { + CPRINTS("Skip enable p%d", port); + return EC_ERROR_INVAL; + } + + CPRINTS("New charge port: p%d", port); + + /* + * Turn off the other ports' sink path FETs, before enabling the + * requested charge port. + */ + for (i = 0; i < CONFIG_USB_PD_PORT_MAX_COUNT; i++) { + if (i == port) + continue; + + if (board_vbus_sink_enable(i, 0)) + CPRINTS("p%d: sink path disable failed.", i); + } + + /* Enable requested charge port. */ + if (board_vbus_sink_enable(port, 1)) { + CPRINTS("p%d: sink path enable failed.", port); + return EC_ERROR_UNKNOWN; + } + + return EC_SUCCESS; +} + +void board_set_charge_limit(int port, int supplier, int charge_ma, int max_ma, + int charge_mv) +{ + /* + * Ignore lower charge ceiling on PD transition if our battery is + * critical, as we may brownout. + */ + if (supplier == CHARGE_SUPPLIER_PD && charge_ma < 1500 && + charge_get_percent() < CONFIG_CHARGER_MIN_BAT_PCT_FOR_POWER_ON) { + CPRINTS("Using max ilim %d", max_ma); + charge_ma = max_ma; + } + + charge_set_input_current_limit( + MAX(charge_ma, CONFIG_CHARGER_INPUT_CURRENT), charge_mv); +} + +uint16_t tcpc_get_alert_status(void) +{ + uint16_t status = 0; + + if (!gpio_pin_get_dt(GPIO_DT_FROM_NODELABEL(gpio_usb_c0_pd_int_odl))) + if (gpio_pin_get_dt( + GPIO_DT_FROM_NODELABEL(gpio_usb_c0_pd_rst_l))) + status |= PD_STATUS_TCPC_ALERT_0; + if (!gpio_pin_get_dt(GPIO_DT_FROM_NODELABEL(gpio_usb_c1_pd_int_odl))) + if (gpio_pin_get_dt( + GPIO_DT_FROM_NODELABEL(gpio_usb_c1_pd_rst_l))) + status |= PD_STATUS_TCPC_ALERT_1; + + return status; +} |