summaryrefslogtreecommitdiff
Commit message (Expand)AuthorAgeFilesLines
* Clear OWNERS for factory/firmware branchfactory-test-7077.114.BBrian Norris2021-09-102-10/+1
* sb_firmware: fixed the last write delaysstabilize-7077.134.Bstabilize-7077.123.Bstabilize-7077.122.Bstabilize-7077.111.Brelease-R44-7077.BSheng-Liang Song2015-06-152-16/+33
* driver: Add BMM150 behind BMI160 support.Gwendal Grignou2015-05-167-42/+291
* cleanup: Use CONFIG_BATTERY_CUT_OFF for supported boardsShawn Nematbakhsh2015-05-1614-128/+31
* mec1322: Correct SPI image offsetsShawn Nematbakhsh2015-05-161-55/+68
* ryu: set HPD as open-drainVincent Palatin2015-05-161-1/+1
* ec: fix -Wuninitialized warning.Yunlian Jiang2015-05-151-2/+2
* Use GCC instead of LD to trigger the linkerVincent Palatin2015-05-152-7/+7
* oak: Add oak EC and PD flash_ec supportRong Chang2015-05-151-1/+3
* kunimitsu: Initial GPIO and Power Sequence supportKevin K Wong2015-05-158-0/+605
* cleanup: Use appropriate image geometry CONFIGsShawn Nematbakhsh2015-05-1531-359/+121
* Fix type mismatch on extern declarationsVincent Palatin2015-05-153-3/+3
* sb_firmware: Fixed firmware version checkSheng-Liang Song2015-05-141-4/+6
* sb_firmware: enable retry for status.fw_update_supportedSheng-Liang Song2015-05-141-2/+2
* sb_firmware: Enable Updates for Simplo Battery Only.Sheng-Liang Song2015-05-141-1/+11
* sb_firmware: Use new delay values suggested by Simplo & TI.Sheng-Liang Song2015-05-141-87/+67
* sb_firmware: check if last full charge is zeroSheng-Liang Song2015-05-143-31/+29
* add hash for locally emerged buildsVincent Palatin2015-05-131-1/+7
* cyan: enable power button to wake up EC from HIB modeli feng2015-05-131-2/+1
* ryu: Add bosh sensor to smaug EC.Gwendal Grignou2015-05-123-0/+56
* driver: Add BMI160 basic driver supportGwendal Grignou2015-05-124-0/+649
* driver: Use common data structure to store default accel valuesGwendal Grignou2015-05-1210-83/+156
* cleanup: Rename image geometry CONFIGsShawn Nematbakhsh2015-05-1236-223/+238
* glados: Initial mainboard commitstabilize-7060.BShawn Nematbakhsh2015-05-1210-1/+436
* power: skylake: Add support for skylake power sequencingShawn Nematbakhsh2015-05-123-3/+250
* make: add generation of sorted symbol mapsstabilize-7059.BVadim Bendebury2015-05-112-4/+9
* ryu: update PD swaps configurationVincent Palatin2015-05-088-14/+94
* cr50: add SPI Slave driverVadim Bendebury2015-05-076-0/+561
* cr50: share board directory among board variantsVadim Bendebury2015-05-0710-219/+8
* ec: Add Inventory commandGwendal Grignou2015-05-074-1/+233
* ryu: enable alternate modes for USB PDVincent Palatin2015-05-074-26/+258
* power: Move EC_CMD_GSV_PAUSE_IN_S5 handler to common codeShawn Nematbakhsh2015-05-0716-138/+87
* CCD: Add documentationAnton Staaf2015-05-071-0/+143
* CCD: Disable ModemManager for CCD USB consolesAnton Staaf2015-05-062-14/+33
* twinkie: fix initialization in sniffer modeVincent Palatin2015-05-061-0/+2
* twinkie: Fix memcpy_to_usbsram destination address.Todd Broch2015-05-061-1/+1
* ryu: add control of switch for USB D+/D-Alec Berg2015-05-062-2/+58
* ryu: remove charge rampingVincent Palatin2015-05-063-54/+0
* ryu: fix Rp pull-ups on CCVincent Palatin2015-05-061-0/+6
* Braswell: Turn on/off the USB power while S5->S3/S3->S5.Hsu Henry2015-05-053-4/+11
* mec1322:Flasherase, flashread, flashwrite offsets adjusted.Divya Jyothi2015-05-052-2/+7
* cyan: Set Motion Sensors to Pre-init state in S3Shamile Khan2015-05-053-4/+47
* pd: fix PDO selection for low voltage boardsstabilize-7039.BVincent Palatin2015-05-051-0/+1
* ryu: update PD electrical parametersVincent Palatin2015-05-052-4/+6
* pd: add explicit setting of D+/D- switch when setting type-C muxesAlec Berg2015-05-0514-22/+50
* ryu: fix physical power button on P5Vincent Palatin2015-05-041-0/+1
* ryu: add Proto 6 supportVincent Palatin2015-05-025-23/+29
* ryu: remove Proto 4 supportVincent Palatin2015-05-023-77/+1
* ryu: fork P4/P5 supportVincent Palatin2015-05-0211-2/+1434
* cli: add ability to read/write memory of different bus widthVadim Bendebury2015-05-021-17/+60
View Lorry Controller Status