summaryrefslogtreecommitdiff
Commit message (Expand)AuthorAgeFilesLines
* bobba: Add support for BMI160 base sensorsstabilize-11020.BJustin TerAvest2018-08-303-20/+21
* signer: modify publishing instructionsVadim Bendebury2018-08-301-3/+4
* nautilus: decrease UART bufferJett Rink2018-08-301-1/+1
* anx74xx: consolidating anx74xx alert handlerJett Rink2018-08-301-90/+42
* common:pd: reset CapCnt variableRuibin Chang2018-08-301-0/+1
* Rammus: enable cbi for EEPROMZhuohao Lee2018-08-301-0/+4
* atlas: add ACOK as wake-from-hibernate sourceCaveh Jalali2018-08-302-3/+3
* atlas: add LID as wake-from-hibernate sourceCaveh Jalali2018-08-291-1/+4
* cr50: Release EC Reset on power button release when SuzyQ detected.Nick Sanders2018-08-294-5/+58
* build: print out remaining RAM spaceJett Rink2018-08-294-10/+26
* chgstv2: Check current battery presence instead of battery_was_removedDaisuke Nojiri2018-08-291-1/+1
* npcx7: Set booter RAM size to 2KBFurquan Shaikh2018-08-291-1/+1
* Prepare to release version 0.4.10Vadim Bendebury2018-08-291-1/+1
* cheza: Support base detectionWai-Hong Tam2018-08-294-2/+194
* kukui: Change FORCE_RESET to ODLNicolas Boichat2018-08-292-4/+4
* gsctool: Reject empty authorization codeCheng-Han Yang2018-08-291-0/+6
* servo_micro: Allow setting the baud rate for usartNicolas Boichat2018-08-298-13/+74
* cheza: Add more power signals for informative purposeWai-Hong Tam2018-08-294-8/+17
* kukui: Enable CONFIG_USB_PD_DUAL_ROLE_AUTO_TOGGLEYilun Lin2018-08-291-0/+1
* charger/mt6370: Fix wrong init IRQ mask.Yilun Lin2018-08-291-1/+1
* kukui: Switch to rev1 by defaultNicolas Boichat2018-08-291-1/+1
* meep: Add charge LED behaviorZick Wei2018-08-294-8/+21
* fingerprint: Flush SPI transaction before increasing CPU clockDaisuke Nojiri2018-08-291-0/+7
* system: Make hibernate console command invoke chipset task if chipset is onFurquan Shaikh2018-08-291-2/+21
* octopus: Call chipset_do_shutdown when hibernating in chipset task contextFurquan Shaikh2018-08-291-1/+13
* atlas: enable active discharge on 5V railCaveh Jalali2018-08-291-2/+2
* Fleex: Enable dynamic motion sensor count andelthanhuang2018-08-292-3/+31
* common:pd: GRL-USB-PD TDA2.2.9 test fail issueRuibin Chang2018-08-291-4/+8
* cr50: add more ccd open capabilitiesMary Ruthven2018-08-292-5/+22
* rdd: use rdd_interrupt for rdd_connect/disconnectMary Ruthven2018-08-292-46/+26
* Revert "ec3po: quit console & interpreter loop when parent process changes."Nick Sanders2018-08-272-10/+6
* servo_micro: Fix DMA mappingsNick Sanders2018-08-272-15/+35
* npcx: don't clear DEVCNT_F_SPI_TRIS bit for chips that use intenal flashCHLin2018-08-261-1/+1
* cr50: enable ccd open from the consoleMary Ruthven2018-08-251-0/+2
* ccd_config: add flag restricting ccd openMary Ruthven2018-08-252-0/+4
* nocturne: Remove CONFIG_SYSTEM_UNLOCKED.stabilize-11005.BAseda Aboagye2018-08-251-3/+0
* servo_v4: clear bbram PD state on rebootNick Sanders2018-08-251-0/+6
* Fleex: Modify shipping mode register and FETelthanhuang2018-08-251-10/+9
* bd99992: add some more register definitionsCaveh Jalali2018-08-242-6/+18
* cheza: Use BC1.2 to detect VBUS presentWai-Hong Tam2018-08-241-1/+1
* chip/npcx: Make check_reset_cause() staticSimon Glass2018-08-241-3/+2
* ec3po: quit console & interpreter loop when parent process changes.Ruben Rodriguez Buchillon2018-08-242-6/+10
* power/mt8183: Power sequence from S5, not G3Nicolas Boichat2018-08-241-19/+22
* cheza: Configure ANX3429 interrupt as open-drainWai-Hong Tam2018-08-234-1/+16
* octopus: update bip for lower power hibernateJett Rink2018-08-233-24/+52
* sn5s330: add low power modeJett Rink2018-08-234-22/+106
* tcpc/mt6370: Fix state debouncing when enable auto-toggling w/o battery.Yilun Lin2018-08-232-11/+14
* tcpm:it83xx: GRL-USB-PD TDA2.1.2.1 BMC testRuibin Chang2018-08-231-0/+22
* usb-pd: Exit DP mode before shutdownDaisuke Nojiri2018-08-232-1/+23
* cr50: only enable rbox wakeup during sleepMary Ruthven2018-08-236-17/+44
View Lorry Controller Status