summaryrefslogtreecommitdiff
Commit message (Expand)AuthorAgeFilesLines
* common: mag_cal: Re-add bias inversionstabilize-quickfix-12871.27.B-masterstabilize-12871.91.B-masterstabilize-12871.65.B-masterstabilize-12871.57.B-masterstabilize-12871.253.B-masterstabilize-12871.24.B-masterstabilize-12871.103.B-masterstabilize-12871.102.B-masterrelease-R81-12871.B-masterGwendal Grignou2020-02-122-9/+9
* ps8818: fix redriver configurationDenis Brockus2020-01-314-9/+200
* Juniper: Add new LGC batteryDavid Huang2020-01-312-0/+29
* kappa: enable ledDevin Lu2020-01-314-6/+77
* puff: Fix a typo in the VBUS ADC config.Sam McNally2020-01-311-1/+1
* waddledoo: Change PP1050_ST power goodAseda Aboagye2020-01-314-13/+5
* driver: bmi160: Fix rounding error in set_offset() and get_offset()Ching-Kang Yen2020-01-313-8/+26
* jinlon: add dual fan control by ecDevin Lu2020-01-318-10/+265
* dratini: change thermal configuration for DVTDevin Lu2020-01-311-7/+7
* usb_pd TCPMv1: Maintain independent MessageID for SOP PrimeAyushee2020-01-313-9/+68
* volteer: Enable USB4.0 modeVijay Hiremath2020-01-311-0/+3
* tglrvp: Enable USB4.0 modeVijay Hiremath2020-01-311-0/+3
* Burnside bridge retimer: Add USB4 mode bitsAyushee2020-01-312-22/+37
* TCPMv1: Add support for USB4.0Ayushee Shah2020-01-319-28/+580
* ioexpander: Fix IOEX_INT after ioex_signal numbering changeEdward Hill2020-01-312-3/+4
* flash_ec: no stderr redirection in flashrom runNamyoon Woo2020-01-301-2/+1
* USB PD: set last rx'd msg ID as invalid before executing soft resetTim Wawrzynczak2020-01-301-0/+1
* hatch: Use GPIO and host event when generating MKBP eventsTim Wawrzynczak2020-01-301-1/+1
* c2d2: initial c2d2 addJett Rink2020-01-309-4/+1098
* npcx: Add driver support for PS/2 interfaceCHLin2020-01-3010-6/+506
* ps8818: allow access to all of the register pagesDenis Brockus2020-01-302-12/+93
* usb: differentiate DTS polarity and normal device polarityDenis Brockus2020-01-306-14/+67
* npcx: enable the host interface mouse channelCHLin2020-01-301-2/+20
* TCPMv1/v2: Move EC_CMD_USB_PD_CONTROL host command to common fileVijay Hiremath2020-01-306-287/+399
* volteer: enable link time optimizationKeith Short2020-01-301-0/+1
* intelrvp: Enable PD 3.0 supportVijay Hiremath2020-01-301-0/+4
* oak: enable link time optimizationKeith Short2020-01-302-2/+4
* waddledoo: Add chg_chips tableAseda Aboagye2020-01-292-0/+17
* volteer: enable PD 3.0 supportKeith Short2020-01-291-0/+6
* PD 3.0: Send Reject messages for refusing swapsDiana Z2020-01-291-11/+13
* PD 3.0: Add AMS start detection to collision avoidanceDiana Z2020-01-292-110/+113
* TCPMv1: Cleanup sending TBT control flags to hostVijay Hiremath2020-01-298-59/+52
* spi: keep HW SPI module enabled longerJett Rink2020-01-293-13/+28
* spi: add flags to spi configurationJett Rink2020-01-296-6/+17
* kohaku : set CONFIG_CHARGER_BQ25710_IDCHG_LIMIT_MA to 6144YongBeum.Ha2020-01-291-1/+1
* waddledoo: Enable USB Type-C redriverAseda Aboagye2020-01-292-0/+11
* driver/retimer: Add support for ON Semi NB7V904MAseda Aboagye2020-01-294-0/+186
* USB-C: Move EC_CMD_GET_PD_PORT_CAPS host command to host command fileVijay Hiremath2020-01-282-43/+43
* TCPMv1/v2: Move EC_CMD_USB_PD_GET_AMODE host command to common fileVijay Hiremath2020-01-284-82/+119
* TCPMv1/v2: Move EC_CMD_USB_PD_DISCOVERY host command to common fileVijay Hiremath2020-01-284-43/+39
* hatch: Add board specific override for board_get_pd_port_location()Tim Wawrzynczak2020-01-281-0/+13
* spi: respond to USB endpoint when SPI disabledJett Rink2020-01-281-3/+0
* puff: Change default VCCST_PG_OD to low.Sam McNally2020-01-281-1/+1
* deltaur: initial addJett Rink2020-01-285-0/+136
* common: vec3: Add init/sub/add functionsYuval Peress2020-01-282-0/+78
* common: mag_cal: update magnetometer to leverage kasaYuval Peress2020-01-287-141/+161
* Charger: change get_vbus_voltage to return EC errorDiana Z2020-01-2815-31/+82
* Charger: Remove unused charger driversDiana Z2020-01-2816-2289/+0
* Charger: Create charger driver structureDiana Z2020-01-2822-833/+1738
* TCPMv2: Ensure Rd is set in Debug Accessory.SNKDiana Z2020-01-281-0/+2
View Lorry Controller Status