summaryrefslogtreecommitdiff
path: root/baseboard
Commit message (Expand)AuthorAgeFilesLines
* baseboard: hatch: Limit printf on serial consoleGwendal Grignou2019-05-141-0/+8
* Revert "octopus: Support keypad function on Bobba"Justin TerAvest2019-05-101-5/+0
* octopus: Support keypad function on BobbaSue Chen2019-05-101-0/+5
* hatch: Enable CONFIG_CMD_CHARGER_DUMPScott Collyer2019-05-091-0/+3
* hatch/kohaku: Account for TCPC reset polarity in ALERT handlerScott Collyer2019-05-081-5/+9
* Octopus: Allow power role swap to sink in S0ixDiana Z2019-05-021-4/+9
* grunt: Improve safe state when entering DP modeEdward Hill2019-04-241-31/+37
* hatch/kohaku: Account for different bc1.2 chipsScott Collyer2019-04-202-14/+0
* common: led_onoff_states: move forward baseboard led_state to common codeDevin Lu2019-04-204-318/+1
* hatch/kohaku: Move HDMI support to board-specific.Tim Wawrzynczak2019-04-191-3/+0
* hatch/kohaku: Remove Type A USB support for Kohaku.Tim Wawrzynczak2019-04-192-13/+0
* hatch/kohaku: Move TCPC definitions to board from baseboardScott Collyer2019-04-172-59/+31
* tcpm: Refactor tcpc_config to include a flags fieldScott Collyer2019-04-176-15/+26
* grunt/usb_pd_policy: Don't disconnect the USB lines while negotiating PDRaul E Rangel2019-04-091-2/+12
* hatch: Enable CONFIG_POWER_S0IX_FAILURE_DETECTIONEvan Green2019-04-031-0/+1
* bip: Delete boardEvan Green2019-04-021-1/+1
* grunt: Check IRQ and HPD in DPStatus message.Edward Hill2019-03-261-1/+1
* grunt: Check DP MF-bit against selected pin cfgEdward Hill2019-03-261-2/+12
* hatch: Enabling tablet modezack_yang2019-03-191-0/+3
* hatch: Enable PP5000_CONTROL for BC1.2 to work in G3Scott Collyer2019-03-161-0/+1
* hatch: Enable sensors sync via dedicated IRQ pinPhilip Chen2019-03-141-5/+1
* hatch: Add CONFIG_DPTFScott Collyer2019-03-131-0/+1
* hatch: Disable HW_RAMP until bq25710 ICO mode is changedScott Collyer2019-03-131-1/+0
* mkbp_event,include/config.h: Clarify MKBP delivery method.Yilun Lin2019-03-071-1/+2
* hatch: Remove CONFIG_USB_PD_VBUS_MEASURE_NOT_PRESENTPhilip Chen2019-03-011-1/+0
* hatch: Add support for BMA253 lid accel sensor and lid angle detectionScott Collyer2019-02-271-0/+11
* hatch: Add support for base accelgyro bmi160 sensorScott Collyer2019-02-271-0/+20
* hatch: Enable CONFIG_CPU_PROCHOT_ACTIVE_LOWPhilip Chen2019-02-191-0/+1
* hatch: Enable bc1.2 supportScott Collyer2019-02-192-1/+22
* Casta: Tune USB mux registersDiana Z2019-02-141-0/+10
* hatch: Enable S0IX config optionsScott Collyer2019-02-131-3/+2
* hatch: Define host battery full factor as 100%Philip Chen2019-02-131-0/+2
* aleena: Enable GPIO-based MKBP event notificationEdward Hill2019-02-121-1/+0
* hatch: Add support for MST (multi stream transport) enableScott Collyer2019-02-123-0/+34
* grunt: Reduce the sensor FIFO sizeEnrico Granata2019-02-061-1/+1
* hatch: Support CBIPhilip Chen2019-02-061-0/+3
* hatch: Add support for PSL wake sourcesScott Collyer2019-01-312-0/+12
* hatch: Add support for fan and temperature sensorsScott Collyer2019-01-301-0/+1
* hatch: Add support for keyboard backlightScott Collyer2019-01-302-0/+5
* hatch: Add support for keyboard scanScott Collyer2019-01-302-0/+30
* hatch: Add smart control for USB-A portsScott Collyer2019-01-302-1/+12
* hatch: Add vboot config options to baseboard.hScott Collyer2019-01-291-0/+5
* hatch: Add support for 2 color LEDScott Collyer2019-01-293-0/+203
* hatch: Add support for charging and USB type CScott Collyer2019-01-296-0/+746
* Fleex: Add new LED state for fully charged in S5Diana Z2019-01-282-3/+24
* Aleena/Kasumi: Add LID sensor config in S0David Huang2019-01-261-0/+5
* Ampton: Set the PS8751 to source mode before enter low power modeJames_Chao2019-01-251-1/+1
* octopus/ampton: disable espi pad when system goes into G3Dino Li2019-01-241-0/+20
* hatch: Add support for power sequencingScott Collyer2019-01-242-1/+103
* hatch: Initial skeleton for hatchScott Collyer2019-01-243-0/+60
View Lorry Controller Status