summaryrefslogtreecommitdiff
path: root/baseboard
Commit message (Expand)AuthorAgeFilesLines
* volteer: Update USB C1 reset for next buildstabilize-volteer-12931.B-masterKeith Short2020-02-262-3/+22
* nucleo-h743zi: Separated into baseboardCraig Hesling2020-02-257-0/+271
* waddledoo: Set CMPOUT as inverted to enable 5VAseda Aboagye2020-02-251-0/+1
* TCPMV1/2: Make the PD Config Flags more consistentSam Hurst2020-02-2210-3/+13
* dedede: Set pullup on PG_PP1050_ST_OD only after RSMRSTAseda Aboagye2020-02-212-0/+18
* zork: enable usb-c FRSwapDenis Brockus2020-02-211-6/+3
* volteer: Increase I2C bus speed to 1 MHz for USB PDKeith Short2020-02-201-2/+2
* waddledoo:Handle EC_AP_PCH_PWROK_OD and ALL_SYS_PWRGDSooraj Govindan2020-02-192-0/+12
* driver/tcpm/it8xxx2: PD driver for chip it8xxx1/8xxx2Ruibin Chang2020-02-194-4/+4
* hatch: Add check for convertible SKUs in lid_angle_peripheral_enableTim Wawrzynczak2020-02-182-4/+6
* tcpci: Rename TCPC_FLAGS_TCPCI_V2_0 to TCPC_FLAGS_TCPCI_REV2_0Edward Hill2020-02-142-3/+3
* trembyle: enable TCPMv2 USB-C PD stackDenis Brockus2020-02-141-1/+4
* zork: HPD for DB OPT3 MST hubEdward Hill2020-02-142-0/+19
* zork: HPD for DB OPT1 HDMIEdward Hill2020-02-142-0/+21
* Kodama: delay to enable charger EOC and TE functionxiong.huang2020-02-141-0/+51
* baseboard/kukui: disable console cmd help in ROEric Yilun Lin2020-02-141-0/+1
* intelrvp: Correct build assert array size comparisonVijay Hiremath2020-02-144-5/+5
* nct38xx: use tcpci rev 2 standard receive and transmitDenis Brockus2020-02-141-0/+2
* zork: allow for the PS8811 needing a retryDenis Brockus2020-02-141-7/+26
* zork: Enable CONFIG_LOW_POWER_IDLEEdward Hill2020-02-141-0/+1
* Temp sensor: Remove action_delay_sec fieldDiana Z2020-02-145-22/+9
* zork: Increase PD max power to 60WEdward Hill2020-02-121-1/+1
* zork: Disable Host command and Fan channelsRaul E Rangel2020-02-111-0/+2
* morphius: add PWM CH0 for LED controlZick Wei2020-02-112-36/+0
* trembyle: initialize PS8811 after AP rail is highDenis Brockus2020-02-112-3/+14
* Waddledee: Initial board fileDiana Z2020-02-113-1/+93
* volteer: enable minimum power requirementKeith Short2020-02-101-0/+9
* kukui: inform AP DP status by USB_MUX eventEric Yilun Lin2020-02-101-7/+17
* juniper: implement otg functionTing Shen2020-02-101-2/+10
* volteer: Increase I2C bus speeds for USB C0 and C1Keith Short2020-02-071-4/+2
* zork: remove hard off check for charger sensor tempDenis Brockus2020-02-071-12/+0
* hatch: Define CONFIG_MKBP_EVENT_WAKEUP_MASK as 0Tim Wawrzynczak2020-02-061-0/+4
* trembyle: adjust gain on USB-A ps8811 for gen2 speedsDenis Brockus2020-02-062-0/+27
* zork: wake up ps8802 before tuning gain adjustmentDenis Brockus2020-02-061-0/+5
* zork: adjust retimer gain adjustmentsDenis Brockus2020-02-061-75/+17
* dedede: Override power_signal_get_level()Aseda Aboagye2020-02-051-0/+17
* dedede: Change PP3300_A PGOOD update methodAseda Aboagye2020-02-053-2/+77
* Charger: Convert boards to use new driver structureDiana Z2020-02-047-0/+101
* volteer/intelrvp: Enable "pe" console commandVijay Hiremath2020-02-042-0/+2
* volteer: add USB3 daughterboard supportstabilize-12881.B-masterCaveh Jalali2020-02-042-6/+79
* honeybuns: Initial skeleton EC imageScott Collyer2020-02-043-0/+75
* PS8818: use read/modify/write for regs with reserved bitsDenis Brockus2020-02-011-40/+50
* ps8802: fix redriver configurationDenis Brockus2020-01-311-0/+59
* ps8818: fix redriver configurationDenis Brockus2020-01-311-0/+97
* waddledoo: Change PP1050_ST power goodAseda Aboagye2020-01-312-11/+3
* volteer: Enable USB4.0 modeVijay Hiremath2020-01-311-0/+3
* hatch: Use GPIO and host event when generating MKBP eventsTim Wawrzynczak2020-01-301-1/+1
* volteer: enable link time optimizationKeith Short2020-01-301-0/+1
* intelrvp: Enable PD 3.0 supportVijay Hiremath2020-01-301-0/+4
* volteer: enable PD 3.0 supportKeith Short2020-01-291-0/+6
View Lorry Controller Status