summaryrefslogtreecommitdiff
path: root/board/arcada_ish
Commit message (Expand)AuthorAgeFilesLines
* config: rename CONFIG_FLASH to CONFIG_FLASH_CROSJeremy Bettis2021-04-271-1/+1
* Revert "config: rename CONFIG_FLASH to CONFIG_FLASH_CROS"stabilize-13935.B-mainJack Rosenthal2021-04-241-1/+1
* config: rename CONFIG_FLASH to CONFIG_FLASH_CROSEric Yilun Lin2021-04-231-1/+1
* Refactor CONFIG_FLASH_SIZE to CONFIG_FLASH_SIZE_BYTESYuval Peress2021-01-151-1/+1
* COIL: Rename CONFIG_I2C_CONTROLLERDiana Z2020-11-051-1/+1
* board: Set Accelerometer range to 4gGwendal Grignou2019-12-171-3/+7
* driver: lsm6dsm: Allow building without CONFIG_ACCEL_FIFOYuval Peress2019-11-211-1/+1
* tablet_mode: Renaming for GMR sensorPhilip Chen2019-09-193-5/+5
* config: Refactor CONFIG_ACCEL_FIFO to enable use of IS_ENABLEDYuval Peress2019-09-031-2/+6
* Remove __7b, __8b and __7bfDenis Brockus2019-07-201-4/+4
* Use 7bit I2C/SPI slave addresses in ECDenis Brockus2019-07-191-4/+4
* arcada: lower i2c bus speed to 400kHzJett Rink2019-07-091-1/+1
* arcada_ish: clean up old commentsJett Rink2019-06-181-7/+8
* ish: remove conditional compilation where possibleDenis Brockus2019-06-171-2/+0
* ish: cleanup ISH specific CONFIG_ definitions and usageDenis Brockus2019-06-141-1/+0
* arcada: use lid switch instead of gpioJett Rink2019-06-051-1/+1
* arcada_ish: hook up 360 hall sensor to ISRJett Rink2019-05-283-3/+17
* driver: lis2mdl: fix magnetometer range/resolutionGwendal Grignou2019-05-231-1/+1
* driver: lsm6dsm: Move the interrupt GPIO into sensor structYuval Peress2019-05-231-0/+4
* board: arcada: Fix magnetometer axis rotationYuval Peress2019-05-161-1/+1
* ish: correct gpio voltage to 3.3Vstabilize-12202.BJett Rink2019-05-131-1/+1
* board: arcarda_ish: Fix gyro matrixGwendal Grignou2019-05-081-1/+1
* arcada_ish: hook up lid open gpio interruptJett Rink2019-05-042-1/+2
* board: arcada_ish: add lis2mdl magnetometerYuval Peress2019-04-242-5/+30
* arcada_ish: Tune D0ix idle target residencyRushikesh S Kadam2019-04-131-2/+2
* ec.tasklist: Consolidate duplicate commentsDaisuke Nojiri2019-04-081-13/+1
* ish/ish5: enable AON low power mode on arcada_ish boardHu, Hebo2019-04-081-0/+12
* arcada_ish: remove unlocked config optionJett Rink2019-04-031-6/+0
* arcada_ish: ensure tests target buildsJett Rink2019-04-031-0/+2
* ish: add memory dma driver for ISH5Leifu Zhao2019-04-021-0/+3
* ish: Add watchdog timerJack Rosenthal2019-03-261-4/+0
* motion: Define macros for custom eventsGwendal Grignou2019-03-201-1/+2
* arcada_ish: set NB_MODE_L going to EC correctlyJett Rink2019-03-183-2/+16
* arcada_ish: add base lis2dh accel sensorJett Rink2019-03-182-5/+56
* arcada_ish: Enable accel interrupts and accel fifoMathew King2019-03-133-2/+19
* arcada_ish: Add the gyro to the motion sensor arrayMathew King2019-03-082-8/+28
* ec: Cleanup ish config optionsMathew King2019-03-012-20/+0
* arcada_ish: add sensor and heci tasksJett Rink2019-02-263-8/+98
* ish: save/restore FPU context only for the task uses FPUHyungwoo Yang2019-02-261-4/+6
* arcada_ish: change GPIO_NB_MODE_L defaultJett Rink2019-02-191-1/+1
* arcada: add hall sensor input GPIO and NB_MODE outJett Rink2019-01-281-1/+6
* arcada: remove gpio lines for I2CJett Rink2019-01-283-8/+6
* arcada: remove executable flag from all filesJett Rink2019-01-245-0/+0
* ISH: Arcada ISH initial enablingShine Liu2019-01-115-0/+159
View Lorry Controller Status