summaryrefslogtreecommitdiff
path: root/board/cr50/gpio.inc
Commit message (Expand)AuthorAgeFilesLines
* coil: cleanup commentsstabilize-rust-13720.B-cr50_stabMary Ruthven2021-01-111-1/+1
* coil: rename spi_master to spi_controllerMary Ruthven2021-01-101-1/+1
* coil: CONFIG_SPI_MASTER->CONFIG_SPI_CONTROLLERMary Ruthven2021-01-101-1/+1
* coil: sps->sppMary Ruthven2021-01-101-1/+1
* coil: CONFIG_SPS->CONFIG_SPPMary Ruthven2021-01-101-1/+1
* coil: cleanup i2c commentsMary Ruthven2021-01-081-7/+7
* coil: i2cm->i2ccMary Ruthven2021-01-071-1/+1
* coil: rename I2CS gpiosMary Ruthven2021-01-071-12/+12
* coil: i2cs -> i2cpMary Ruthven2021-01-071-2/+2
* apply INT_AP_L extension on I2CS interfaceNamyoon Woo2020-05-291-6/+9
* cr50: Provision DIOM4 as inputVadim Bendebury2020-02-271-0/+10
* make DIOB3 interruptible and wakable for EC-EFS2Namyoon Woo2020-02-081-0/+11
* cr50: add support for using a strap pin as a ccd gpioMary Ruthven2020-01-171-0/+8
* add BOARD_EC_CR50_COMM_SUPPORT to board propertiesNamyoon Woo2020-01-141-3/+5
* cr50: correct the comment on ENTERING_RW in gpio.incNamyoon Woo2019-10-071-2/+5
* g: allow I2CS operate without hardware resetsVadim Bendebury2019-09-051-0/+12
* cr50: add gpio assignments descriptionVadim Bendebury2019-08-021-0/+29
* LICENSE: remove unnecessary (c) after CopyrightTom Hughes2019-06-191-1/+1
* cr50: make sys_rst_l_out pseudo open drainMary Ruthven2019-04-051-6/+5
* cr50: make ccd_mode_l pseudo open drainMary Ruthven2019-04-041-8/+3
* cr50: use interrupts for ap_stateMary Ruthven2019-03-061-0/+6
* cr50: rename ap and ec detect gpiosMary Ruthven2019-02-011-4/+4
* cr50: change EC_TX_CR50_RX gpioMary Ruthven2019-02-011-1/+3
* cr50: add more obvious sections in gpio.incMary Ruthven2019-01-311-1/+11
* cr50: Changes to support closed source EC factory modeKeith Short2019-01-081-0/+12
* cr50: speed up bit bang EC programmingVadim Bendebury2018-08-161-1/+3
* cr50:usb_spi: add Cheza EC supportMary Ruthven2018-04-101-4/+11
* cr50: create ap_uart state machineMary Ruthven2018-02-021-0/+1
* cr50: Split servo state machine into its own fileRandall Spangler2017-09-011-1/+1
* cr50: Split AP state machine into its own fileRandall Spangler2017-08-301-1/+1
* cr50: Split EC state machine into its own fileRandall Spangler2017-08-251-1/+1
* cr50: Refactor Rdd state machineRandall Spangler2017-08-231-1/+7
* g: add 'recover hosed slave' i2cs capabilityVadim Bendebury2017-08-171-0/+11
* cr50: add a pulldown to spi mosi and clkMary Ruthven2017-08-011-2/+2
* cr50: introduce means of detecting chip running in factory modeVadim Bendebury2017-07-301-0/+7
* cr50: Enable EC UART bit banging.Aseda Aboagye2017-06-071-0/+7
* cr50: Only drive CCD_MODE_L when in CCD mode.Aseda Aboagye2017-03-071-3/+5
* cr50: rework sleep state and tpm reset triggersVadim Bendebury2017-02-071-2/+1
* cr50: Implement reading all strapping pins for board configScott2017-01-241-2/+4
* cr50: describe GPIO assignmentVadim Bendebury2017-01-191-0/+37
* cr50: use the correct reset signal for gru and reefMary Ruthven2017-01-181-6/+14
* cr50: change uart rx to wake_lowMary Ruthven2016-12-081-1/+1
* Cr50: I2CM: Enable i2c master for accessing INA chipsScott2016-10-111-4/+8
* Cr50: Add gpio input for platform reset (plt_rst_l)Scott2016-09-231-0/+1
* cr50: make device state detect level triggeredMary Ruthven2016-09-211-3/+3
* cr50: remove unused detect_off interruptMary Ruthven2016-09-211-13/+6
* g: generate AP_INT_L pulse after i2cs processing finishedVadim Bendebury2016-09-151-1/+1
* cr50: stop using the AP uart to detect servoMary Ruthven2016-09-131-10/+4
* cr50: remove the pullup on sys_rst on kevinMary Ruthven2016-09-091-4/+1
* Revert "cr50: remove internal pull up on DIOM0"Mary Ruthven2016-09-061-1/+4
View Lorry Controller Status