summaryrefslogtreecommitdiff
path: root/board/cr50/gpio.inc
Commit message (Expand)AuthorAgeFilesLines
* cr50:usb_spi: add Cheza EC supportMary Ruthven2018-04-101-4/+11
* cr50: create ap_uart state machineMary Ruthven2018-02-021-0/+1
* cr50: Split servo state machine into its own fileRandall Spangler2017-09-011-1/+1
* cr50: Split AP state machine into its own fileRandall Spangler2017-08-301-1/+1
* cr50: Split EC state machine into its own fileRandall Spangler2017-08-251-1/+1
* cr50: Refactor Rdd state machineRandall Spangler2017-08-231-1/+7
* g: add 'recover hosed slave' i2cs capabilityVadim Bendebury2017-08-171-0/+11
* cr50: add a pulldown to spi mosi and clkMary Ruthven2017-08-011-2/+2
* cr50: introduce means of detecting chip running in factory modeVadim Bendebury2017-07-301-0/+7
* cr50: Enable EC UART bit banging.Aseda Aboagye2017-06-071-0/+7
* cr50: Only drive CCD_MODE_L when in CCD mode.Aseda Aboagye2017-03-071-3/+5
* cr50: rework sleep state and tpm reset triggersVadim Bendebury2017-02-071-2/+1
* cr50: Implement reading all strapping pins for board configScott2017-01-241-2/+4
* cr50: describe GPIO assignmentVadim Bendebury2017-01-191-0/+37
* cr50: use the correct reset signal for gru and reefMary Ruthven2017-01-181-6/+14
* cr50: change uart rx to wake_lowMary Ruthven2016-12-081-1/+1
* Cr50: I2CM: Enable i2c master for accessing INA chipsScott2016-10-111-4/+8
* Cr50: Add gpio input for platform reset (plt_rst_l)Scott2016-09-231-0/+1
* cr50: make device state detect level triggeredMary Ruthven2016-09-211-3/+3
* cr50: remove unused detect_off interruptMary Ruthven2016-09-211-13/+6
* g: generate AP_INT_L pulse after i2cs processing finishedVadim Bendebury2016-09-151-1/+1
* cr50: stop using the AP uart to detect servoMary Ruthven2016-09-131-10/+4
* cr50: remove the pullup on sys_rst on kevinMary Ruthven2016-09-091-4/+1
* Revert "cr50: remove internal pull up on DIOM0"Mary Ruthven2016-09-061-1/+4
* Cr50: Preliminary I2CS TPM2.0 driverScott2016-09-051-3/+10
* cr50: unlock consoleMary Ruthven2016-09-011-9/+1
* cr50: remove internal pull up on DIOM0Mary Ruthven2016-08-311-4/+1
* Revert "cr50: remove internal pull up on DIOM0"Vadim Bendebury2016-08-261-1/+2
* Cr50: Tweak some comments about UART0_RXBill Richardson2016-08-241-9/+12
* cr50: remove internal pull up on DIOM0Mary Ruthven2016-08-231-2/+1
* Cr50: Remove unused AP_WP_L GPIOBill Richardson2016-08-191-5/+0
* Cr50: The battery-present gpio is active lowBill Richardson2016-08-051-3/+3
* Cr50: Sample slave configuration pins at PORScott2016-08-031-0/+4
* cr50: fix wake pin handling when resuming from sleepMary Ruthven2016-07-281-2/+3
* cr50: add INA 3V3 load switch GPIOVincent Palatin2016-07-201-0/+4
* g: tristate spi master pinsMary Ruthven2016-07-141-1/+10
* cr50: disable UART0 RXMary Ruthven2016-07-111-2/+8
* cr50: Add pull down on UART TX signalsMary Ruthven2016-06-191-5/+9
* cr50: dont drive UART output if servo is connectedMary Ruthven2016-05-271-1/+10
* cr50: monitor the state of Servo, the EC, and APMary Ruthven2016-05-271-1/+18
* cr50: set SYS_RST_L as an inputMary Ruthven2016-04-291-1/+1
* Cr50: Change SYS_RST output to SYS_RST_L inoutBill Richardson2016-04-161-3/+14
* cr50: enable AP and EC UART in CCD MODEMary Ruthven2016-04-151-8/+8
* cr50: fix AP UARTMary Ruthven2016-04-141-2/+2
* cr50: default to CCD PHYMary Ruthven2016-04-131-5/+10
* cr50: enable AP and EC UART forwardingMary Ruthven2016-04-071-2/+2
* Cr50: Specify pinmux wake sources in gpio.incBill Richardson2016-04-051-1/+1
* cr50: update GPIOsMary Ruthven2016-03-291-8/+8
* Cr50: SAFE MODE: all GPIOs are inputs for Kevin0stabilize-7978.Bstabilize-7978.18.BBill Richardson2016-02-271-10/+10
* Cr50: Configure GPIOs for Kevin proto0Bill Richardson2016-02-271-4/+59
View Lorry Controller Status