summaryrefslogtreecommitdiff
path: root/board/elm/board.c
Commit message (Expand)AuthorAgeFilesLines
* oak: usb_mux: Split struct usb_mux in oak boardsTomasz Michalec2022-09-131-3/+6
* Update license boilerplate text in source code filesMike Frysinger2022-09-121-1/+1
* tree-wide: const-ify argv for console commandsCaveh Jalali2022-09-011-1/+1
* board/elm/board.c: Format with clang-formatJack Rosenthal2022-06-281-55/+43
* usbc: wrap task_set_event to have an explicit port argumentFabio Baltieri2022-05-271-1/+1
* i2c: Use declared initializers for i2c_ports: boards a-lKeith Short2021-11-301-3/+15
* tree: Make all console commands staticTom Hughes2021-10-151-2/+1
* adc: Remove adc_chip.h where adc.h is usedCaveh Jalali2021-08-271-1/+0
* lid_angle: Create a common callback for lid angle changesWai-Hong Tam2021-08-051-1/+1
* COIL: Rename motion sense address macrosDiana Z2021-06-091-2/+2
* COIL: Rename MODULE_SPI_MASTER to MODULE_SPI_CONTROLLERCaveh Jalali2021-06-031-2/+2
* board: Remove HAS_TASK_MOTIONSENSE when always definedGwendal Grignou2021-02-221-2/+0
* spi: Pass in spi_device as argument to spi_enable instead of portTom Hughes2021-01-281-2/+2
* task_set_event: remove the wait argumentDawid Niedzwiecki2020-12-141-2/+2
* Replace I2C_GET_ADDR with I2C_STRIP_FLAGSYuval Peress2020-11-021-1/+1
* Charger: Add dynamic charger chip countDiana Z2020-07-111-1/+0
* usb_mux: retimer: mux as chained mux and retimerDenis Brockus2020-02-281-1/+2
* Temp sensor: Remove action_delay_sec fieldDiana Z2020-02-141-4/+4
* Charger: Convert boards to use new driver structureDiana Z2020-02-041-0/+10
* board: Set Accelerometer range to 4gGwendal Grignou2019-12-171-2/+2
* Rename CONFIG_USB_PD_PORT_COUNT as CONFIG_USB_PD_PORT_MAX_COUNTKarthikeyan Ramasubramanian2019-11-011-3/+3
* Remove __7b, __8b and __7bfDenis Brockus2019-07-201-8/+10
* Use 7bit I2C/SPI slave addresses in ECDenis Brockus2019-07-191-7/+8
* TCPC: Make tcpc_config handle other bus typesDaisuke Nojiri2019-06-101-1/+8
* common: motion_sense: Require CONFIG_MOTION_SENSOR_MAX_COUNTYuval Peress2019-06-051-38/+41
* usb-c: use higher priority task for interruptsJett Rink2018-11-141-4/+1
* ss-mux: remove unused port_addr initializationv2.0.0Jett Rink2018-09-171-1/+0
* type: Rename matrix_3x3_t to mat33_fp_tYilun Lin2018-09-131-2/+2
* board: Clean up DMA channel mappingNicolas Boichat2018-07-231-3/+2
* board: In motion sensor array, remove assignment to 0Gwendal Grignou2018-03-141-28/+0
* charge_manager: Enter safe mode at bootShawn Nematbakhsh2017-11-021-12/+0
* charge_ramp: Move ramp allowed / ilim callbacks to common codeShawn Nematbakhsh2017-10-061-33/+0
* power: Add flags parameter to power_signal_infoFurquan Shaikh2017-10-031-2/+2
* Treat SYSTEM_IMAGE_RW_B also as RW copyDaisuke Nojiri2017-09-091-2/+1
* driver: Move PI3USB9281 to bc12 directory.Aseda Aboagye2017-07-311-1/+1
* common: sensors: add extra sensor attributesNick Vaccaro2017-05-181-0/+4
* charge_state_v2: Limit i/p current to meet allowed MAX i/p system powerVijay Hiremath2016-12-051-2/+4
* reef/pyro/elm/amenia/snappy: Remove false battery critical messageVijay Hiremath2016-10-251-3/+1
* cleanup: Rename charge_temp_sensor_get_val() to charge_get_battery_temp()Vijay Hiremath2016-10-141-1/+1
* elm: disable 3.3V to ANX7688 by default and enable it in board_power_on_pd_mcu.Milton Chiang2016-10-131-0/+2
* charge_manager: Pass uncapped / max current to current limit callbackShawn Nematbakhsh2016-09-131-1/+1
* driver: kionix: Remove variant field.Gwendal Grignou2016-09-011-4/+1
* cleanup: DECLARE_CONSOLE_COMMAND only needs 4 argsBill Richardson2016-08-241-2/+1
* Use CONFIG_DPTF flag instead of THROTTLE_AP.Ravi Chandra Sadineni2016-07-301-14/+0
* Elm: Allow rejected 'Dont charge' request on initRyan Zhang2016-07-171-0/+14
* Elm: Update max input current for safetyRyan Zhang2016-07-101-0/+2
* Revert "elm: get VBUS statue from GPIO"Koro Chen2016-06-171-1/+1
* elm: anx7688: make anx7688 always onKoro Chen2016-06-161-17/+10
* elm: anx7688: add anx7688 hpd driverRong Chang2016-06-161-23/+71
* elm: get VBUS statue from GPIOYH Huang2016-05-311-1/+1
View Lorry Controller Status