summaryrefslogtreecommitdiff
path: root/board/kukui/gpio.inc
Commit message (Expand)AuthorAgeFilesLines
* ish: Trim down the release branchstabilize-wristpin-14469.59.B-ishstabilize-voshyr-14637.B-ishstabilize-quickfix-14695.187.B-ishstabilize-quickfix-14695.124.B-ishstabilize-quickfix-14526.91.B-ishstabilize-14695.85.B-ishstabilize-14695.107.B-ishstabilize-14682.B-ishstabilize-14633.B-ishstabilize-14616.B-ishstabilize-14589.B-ishstabilize-14588.98.B-ishstabilize-14588.14.B-ishstabilize-14588.123.B-ishstabilize-14536.B-ishstabilize-14532.B-ishstabilize-14528.B-ishstabilize-14526.89.B-ishstabilize-14526.84.B-ishstabilize-14526.73.B-ishstabilize-14526.67.B-ishstabilize-14526.57.B-ishstabilize-14498.B-ishstabilize-14496.B-ishstabilize-14477.B-ishstabilize-14469.9.B-ishstabilize-14469.8.B-ishstabilize-14469.58.B-ishstabilize-14469.41.B-ishstabilize-14442.B-ishstabilize-14438.B-ishstabilize-14411.B-ishstabilize-14396.B-ishstabilize-14395.B-ishstabilize-14388.62.B-ishstabilize-14388.61.B-ishstabilize-14388.52.B-ishstabilize-14385.B-ishstabilize-14345.B-ishstabilize-14336.B-ishstabilize-14333.B-ishrelease-R99-14469.B-ishrelease-R98-14388.B-ishrelease-R102-14695.B-ishrelease-R101-14588.B-ishrelease-R100-14526.B-ishfirmware-cherry-14454.B-ishfirmware-brya-14505.B-ishfirmware-brya-14505.71.B-ishfactory-kukui-14374.B-ishfactory-guybrush-14600.B-ishfactory-cherry-14455.B-ishfactory-brya-14517.B-ishJack Rosenthal2021-11-051-107/+0
* kukui: pull up SPI1_NSS (CS_L).Eric Yilun Lin2020-05-251-1/+1
* krane: add it5205 driverTing Shen2019-09-051-2/+3
* krane: detect pogo charger in adc interruptTing Shen2019-06-201-3/+5
* kukui: implement pogo charge logicTing Shen2019-06-201-1/+2
* kukui: Enable interrupts from hall sensor.Yilun Lin2019-05-141-2/+2
* krane: Reverse BC12 OE in order to fix USBAlexandru M Stan2019-05-121-1/+1
* kukui: implement pogo adc interruptTing Shen2019-05-021-4/+2
* kukui: Remove adc GPIO_USBC_THERM.Yilun Lin2019-05-021-8/+1
* kukui: Runtime configure GPIO settings between rev1 and rev2.Yilun Lin2019-03-071-22/+7
* kukui: Fix unable to source power to peripheral.Yilun Lin2019-02-191-1/+1
* kukui: Add BOARD_REV 2 configs.Yilun Lin2019-01-231-3/+25
* kukui: Remove BOARD_REV 0 GPIO configs.Yilun Lin2019-01-221-21/+0
* kukui: Enable DP.Yilun Lin2018-11-271-1/+1
* kukui/emmc: Share EXTI15 interrupt between SPI and eMMCNicolas Boichat2018-10-301-9/+3
* power/mt8183: Implement watchdog-initiated resetNicolas Boichat2018-10-251-3/+3
* kukui: USB_C0_HPD_OD should be GPIO_ODR_HIGHTony Lin2018-10-121-1/+1
* kukui: Change FORCE_RESET to ODLNicolas Boichat2018-08-291-1/+1
* kukui: Hack away SPI1_NSS on rev0Nicolas Boichat2018-08-231-4/+11
* kukui: Update GPIO for board rev1.Yilun Lin2018-08-221-10/+34
* kukui: PMIC_WATCHDOG_L should follow status of PMIC_WATCHDOG_LAyo Wu2018-08-201-2/+2
* kukui: Set AP_SYS_RST_L to GPIO_OUT_LOW instead of ODRtonycwlin2018-08-161-1/+1
* charger/mt6370: Init charger IRQs.Yilun Lin2018-08-011-1/+1
* kukui: Use MODULE_SPI_FLASH for eMMC emulation pinsNicolas Boichat2018-07-231-1/+1
* power/mt8183: Fix PMIC_EN_ODL polarity, watchdog signalNicolas Boichat2018-07-231-1/+1
* kukui: Fix bmi160 i2c2 config on wrong GPIO PIN.Yilun Lin2018-07-201-2/+2
* kukui: Disable vsync, motion sensor in RO.Yilun Lin2018-07-181-0/+2
* kukui: emulate eMMC boot mode using SPI controller.Nicolas Boichat2018-07-111-2/+10
* kukui: GPIO fixups, and mirror AP watchdog input to outputNicolas Boichat2018-07-031-5/+5
* kukui: Initial setup for ec.Yilun Lin2018-06-301-0/+91
View Lorry Controller Status