summaryrefslogtreecommitdiff
path: root/board/volteer/board.h
Commit message (Expand)AuthorAgeFilesLines
* volteer: Enable CONFIG_DEBUG_ASSERT_BRIEFKeith Short2020-12-031-0/+1
* Volteer: Remove PRL stringsDiana Z2020-11-181-0/+3
* volteer: Enabling sourcing of 4.5A on type-C portsKeith Short2020-11-121-0/+6
* usb: Remove references to usb23Caveh Jalali2020-11-061-11/+0
* COIL: Rename CONFIG_I2C_CONTROLLERDiana Z2020-11-051-1/+1
* volteer: remove volteer_tcpmv1Keith Short2020-10-161-15/+0
* Revert "volteer: Move USB PID to board files"Abe Levkoy2020-09-281-7/+0
* volteer: Move USB PID to board filesAbe Levkoy2020-09-181-0/+7
* volteer: Support board-specific TCPC configSamsp_Liu2020-08-261-0/+9
* volteer: Support board-specific currentSamsp_Liu2020-08-261-0/+4
* Revert "volteer: Disable USB PD extended messages"Abe Levkoy2020-08-211-3/+0
* bmi260: move BMI260 init file into .init.rom sectionKeith Short2020-08-201-1/+7
* volteer: Support board-specific power parametersSamsp_Liu2020-08-111-0/+14
* volteer: Disable USB PD extended messagesAbe Levkoy2020-07-291-0/+3
* bmi260: Add support for using compressed configKeith Short2020-07-101-0/+1
* volteer: move ppc_chips[] from baseboard to boardDavid Huang2020-07-051-0/+3
* volteer: Move USB DB checks from baseboardKeith Short2020-07-021-0/+2
* volteer: Update GPIO namesAbe Levkoy2020-07-011-1/+1
* volteer: Enable DSW_PWROK pass-throughAbe Levkoy2020-06-261-1/+1
* volteer: Remove c10_gate_changeAbe Levkoy2020-06-251-3/+0
* Volteer: create new board target for TCPMv1Keith Short2020-06-181-0/+8
* volteer: add USB-A power enable and disableKeith Short2020-06-151-0/+6
* volteer: remove VSYNC sensorstabilize-lazor-13278.B-masterKeith Short2020-06-091-1/+0
* volteer: enable lid angle supportKeith Short2020-05-161-0/+5
* volteer: Enable EFS2Daisuke Nojiri2020-05-141-0/+2
* volteer: set H1 packet mode GPIO lowKeith Short2020-05-091-0/+1
* malefor: turn off USB4 and Thunderbolt supportxiong.huang2020-04-281-0/+6
* volteer: move the PWM configuration and LED support from baseboard to boardsxiong.huang2020-04-281-0/+15
* volteer: Add board config for BMI260Ching-Kang Yen2020-04-241-0/+8
* Volteer/baseboard: Move I2C bus configuration to variantJosh Tsai2020-04-151-0/+16
* icelake: Cleanup power sequencing for IceLake/TigerLake/JasperLakeKeith Short2020-04-091-1/+0
* malefor: move sensors support from baseboard to boardxiong.huang2020-03-261-0/+21
* Volteer: move USB product ID to baseboardstabilize-12859.B-masterKeith Short2020-01-241-8/+0
* volteer: enable tablet mode supportKeith Short2020-01-091-0/+1
* volteer: add motionsense supportKeith Short2020-01-071-1/+1
* volteer: add support for volume up/down buttonsKeith Short2019-12-111-1/+2
* volteer: Enable BC1.2 charge rampVijay Hiremath2019-12-071-19/+20
* volteer: Enable USB-C Port 1Vijay Hiremath2019-12-041-0/+2
* volteer: disable CONFIG_BRINGUPKeith Short2019-11-211-6/+0
* volteer: Add USB-C policyVijay Hiremath2019-11-211-0/+8
* Volteer: configure USBC port 0Keith Short2019-11-121-0/+8
* volteer: add initial battery supportKeith Short2019-11-091-0/+5
* volteer: Configure ADC channelsKeith Short2019-11-081-3/+0
* volteer: Add manual power sequencingKeith Short2019-11-011-0/+2
* eSPI: Configure SLP_S3, SLP_S4 separatelyAbe Levkoy2019-10-301-1/+0
* volteer: Configure power sequencing signalsAbe Levkoy2019-10-171-0/+7
* cometlake: Cleanup GPIO_PCH_SYS_PWROKKeith Short2019-10-151-0/+1
* volteer: enable CONFIG_BRINGUPKeith Short2019-10-111-0/+6
* volteer: Configure GPIOs connected to keyboardAbe Levkoy2019-10-051-0/+1
* volteer: Add RTC resetKeith Short2019-09-291-0/+1
View Lorry Controller Status