summaryrefslogtreecommitdiff
path: root/board
Commit message (Expand)AuthorAgeFilesLines
* it8380dev: add KBC/KMSC moduleDino Li2015-03-224-28/+61
* cr50: added cr50 a1 chipSheng-Liang Song2015-03-208-0/+220
* honeybuns: fix CC voltage thresholdsVincent Palatin2015-03-121-4/+4
* honeybuns: fix CC line sensing ADCVincent Palatin2015-03-121-1/+1
* honeybuns: add HX3 hub configurationVincent Palatin2015-03-122-1/+117
* honeybuns: Initial /board filesScott Collyer2015-03-127-0/+727
* mec1322: Add flash physical interface functionsShawn Nematbakhsh2015-03-125-3/+11
* spi_flash: Add protect support for W25X40Shawn Nematbakhsh2015-03-113-1/+5
* Ryu: Share SensorHub UART control with ServoAnton Staaf2015-03-101-1/+3
* llama: enable the EC backlight override for mediatek platform.Ben Lok2015-03-091-0/+1
* llama: implement battery ship shutdown modeyh.huang2015-03-092-1/+40
* samus: ryu: allow charge ramp on CDP and proprietary chargersAlec Berg2015-03-072-4/+14
* samus: limit input current when batt near full and 5V chargerAlec Berg2015-03-062-23/+51
* samus_pd: disable i2cxfer console command to save spaceAlec Berg2015-03-061-0/+1
* Ryu: Add support for AP and SH console forwarding over USBAnton Staaf2015-03-043-12/+95
* USB Stream: Make RX and TX buffer sizes configurableAnton Staaf2015-03-031-0/+2
* Producer/Consumer: Convert USART and USB Stream driversAnton Staaf2015-03-021-11/+51
* plankton: always run as UFP when in USB hub modeVic Yang2015-03-023-10/+25
* samus: don't unwedge charging when purposely discharging on ACAlec Berg2015-02-283-3/+23
* samus_pd: Skip pericom detection if we're sourcing VBUSShawn Nematbakhsh2015-02-271-14/+20
* npcx: Use SPI status register instead of pstateRandall Spangler2015-02-261-1/+1
* cr50: enable signed RW imagesBill Richardson2015-02-252-0/+32
* pd: Massage initialization at task start.Todd Broch2015-02-2512-9/+107
* WIP - Nuvoton 30-Jan patchRandall Spangler2015-02-253-16/+26
* samus: make sure EC sends battery percentage to PD on changeAlec Berg2015-02-251-1/+6
* Remove ryu_p1 boardVic Yang2015-02-249-854/+0
* samus_pd: make shmem command optional, disable on samus_pdAlec Berg2015-02-241-0/+1
* samus: change USB type-A ports to default to CDPAlec Berg2015-02-231-0/+1
* ryu: add charge ramp moduleAlec Berg2015-02-214-2/+60
* samus_pd: remove resetting pericom 30 sec after detecting SDPAlec Berg2015-02-211-20/+3
* samus: Only enable VCORE_PGOOD interrupt when it is validDuncan Laurie2015-02-201-0/+15
* samus: samus_pd: Increase task stack sizesShawn Nematbakhsh2015-02-202-7/+5
* samus: add i2c retries to backlight controlAlec Berg2015-02-201-15/+69
* cr50: Separate ARM core GPIOs from pinmux configurationBill Richardson2015-02-203-20/+71
* samus: initiailze boostin_voltage in extpower moduleAlec Berg2015-02-181-1/+1
* samus: panic reboot EC if PD MCU crashesAlec Berg2015-02-182-0/+7
* samus: add charge ramp moduleAlec Berg2015-02-183-0/+104
* samus: Only update fan speeds every N secondsBill Richardson2015-02-181-0/+1
* pd: charge_manager: make new VBUS charge supplierAlec Berg2015-02-184-21/+101
* samus: avoid attempting unwedge charge circuit if VBUS is at 5VAlec Berg2015-02-181-9/+20
* samus: disable i2cscan console command to save spaceAlec Berg2015-02-181-4/+5
* make idlestats console command optionalVincent Palatin2015-02-181-0/+1
* samus: avoid waking extpower task until task has been initializedAlec Berg2015-02-171-2/+8
* samus: increase extpower task stack sizeAlec Berg2015-02-141-1/+1
* pd_log: Add command to request PD MCU to write a logShawn Nematbakhsh2015-02-121-0/+17
* samus: unwedge charge circuit if not charging for long timeAlec Berg2015-02-121-12/+105
* pd: DRP: VCONN should be off at start of pd task.Todd Broch2015-02-124-0/+61
* samus: fix won't charge after zinger plugged in during EC rebootAlec Berg2015-02-101-1/+2
* CCD: Remove CCD specific board connect and disconnectAnton Staaf2015-02-101-18/+0
* stm32: Add delay after enabling peripheral clockVic Yang2015-02-102-0/+6
View Lorry Controller Status