summaryrefslogtreecommitdiff
path: root/board
Commit message (Expand)AuthorAgeFilesLines
* oak: allow charging of dead battery requesting nilstabilize-8104.BYH Huang2016-03-231-0/+1
* it83xx: keyboard: remove "CONFIG_IT83XX_KEYBOARD_KSI_WUC_INT" and fix ISRDino Li2016-03-221-1/+0
* chip: it83xx: remove "CHIP_FAMILY_IT839X"Dino Li2016-03-221-2/+0
* GPIO: Rename and move board_set_gpio_hibernate_stateAnton Staaf2016-03-212-2/+2
* servo_micro: add initial servo_micro buildNick Sanders2016-03-166-0/+459
* oak: Clean up CONFIG_PMIC_FW_LONG_PRESS_TIMER related codesKoro Chen2016-03-161-1/+0
* oak: rev5: increase cycle time for LED in SUSPENDWei-Ning Huang2016-03-161-2/+9
* chell: Indicate when charging in suspendDuncan Laurie2016-03-151-2/+7
* kevin: Add rk3399 power sequencingShawn Nematbakhsh2016-03-144-3/+18
* Cr50: cleanup: put macro args inside parensBill Richardson2016-03-111-1/+1
* kunimitsu: remove CONFIG_POWER_SHUTDOWN_PAUSE_IN_S5Kevin K Wong2016-03-111-1/+0
* Kunimitsu/Lars: correct adc voltage readingKyoung Kim2016-03-112-2/+16
* kevin: Initial board commitShawn Nematbakhsh2016-03-107-0/+785
* Lars: Manually Revert "Lars: Add ALS support"Ryan Zhang2016-03-084-24/+5
* CR50: move platform independent stub calls back to third_partynagendra modadugu2016-03-081-22/+0
* npcx: Rename CONFIG_SHI to CONFIG_HOSTCMD_SPSShawn Nematbakhsh2016-03-081-1/+1
* lucid: fix adc vbus sensingMary Ruthven2016-03-081-2/+2
* CR50: set result size in _cpri__GenerateKeyEcc, _cpri__GetEphemeralEccnagendra modadugu2016-03-071-3/+11
* oak: Fix rev5 battery LEDKoro Chen2016-03-071-12/+17
* npcx: Add CHIP_VARIANT variant for different versions of npcx ec.Mulin Chao2016-03-053-3/+6
* npcx: Add 1.8V IO support for some GPIOs and I2C pins.Mulin Chao2016-03-052-2/+20
* oak: set up base accelerometer rotation matrixRicky Liang2016-03-041-1/+8
* oak: fix issues on building oak rev1-4 ECRong Chang2016-03-033-19/+22
* chell: Enable HW charge ramping for BC1.2 suppliersShawn Nematbakhsh2016-03-022-0/+35
* oak: enable lid angle updateRong Chang2016-03-022-0/+7
* oak: change the default board revision to OAK_REV5.Ben Lok2016-03-021-1/+1
* NPCX: Convert keyboard pins to use ALTERNATE macroAnton Staaf2016-03-024-6/+37
* oak: updates for rev5Ben Lok2016-03-015-80/+151
* oak: Add base accel & gyro via SPI bus for rev5Ben Lok2016-03-015-9/+176
* oak: Add kx022 lid accelerometer for rev5.Ben Lok2016-03-013-4/+60
* Cr50: SAFE MODE: all GPIOs are inputs for Kevin0stabilize-7978.Bstabilize-7978.18.BBill Richardson2016-02-271-10/+10
* cr50: use the correct signer invocation optionsVadim Bendebury2016-02-271-0/+1
* Cr50: Configure GPIOs for Kevin proto0Bill Richardson2016-02-272-4/+65
* Cr50: cleanup: Remove some unneccessary codeBill Richardson2016-02-272-11/+0
* lucid: add support to detect BC1.2 suppliersMary Ruthven2016-02-262-24/+53
* oak: Enable TI OPT3001 ambient light sensor for rev5Ben Lok2016-02-263-0/+26
* glados_pd: Add WP_L input GPIO for future boardsShawn Nematbakhsh2016-02-253-1/+22
* cleanup: Add warning comment to gpio.inc filesBill Richardson2016-02-2540-19/+122
* Cr50: Remove GPIOs left over from FPGA boardsBill Richardson2016-02-252-80/+4
* Cr50: Cleanup some of the GPIO handling codeBill Richardson2016-02-251-10/+10
* jerry: Increase UART TX buffer size.Aseda Aboagye2016-02-231-0/+4
* cr50: upgrade: fix debug messages to show address instead of offsetVadim Bendebury2016-02-231-1/+2
* CR50: add in-place decrypt support for AES-CFBnagendra modadugu2016-02-231-36/+17
* Lars_PD: GPIO correctionKyoung Kim2016-02-221-1/+1
* cr50: Switch from ALTERNATE to PINMUX macrosAnton Staaf2016-02-221-22/+23
* GPIO: Move definitions of GPIO_KB_INPUT and OUTPUTAnton Staaf2016-02-2221-39/+32
* Kunimitsu: Enable config REPLACE_LOADER_WITH_BSS_SLOWShobhit Srivastava2016-02-191-0/+1
* kunimitsu: hibernate: enable PseudoG3 support at board levelKevin K Wong2016-02-186-7/+52
* config: it83xx: remove "CONFIG_IT83XX_PECI_WITH_INTERRUPT"Dino Li2016-02-171-1/+0
* Lars: S0ix/S3 EC power improvementKyoung Kim2016-02-171-2/+2
View Lorry Controller Status