summaryrefslogtreecommitdiff
path: root/board
Commit message (Expand)AuthorAgeFilesLines
* asurada_scp: add dummy board implementationsTzung-Bi Shih2020-06-035-0/+91
* servo_v4p1: Initial checkin of firmwareSam Hurst2020-06-025-0/+586
* volteer: add support for USB4 Gen3Keith Short2020-06-021-5/+21
* asurada: fix incorrect sensor nameTing Shen2020-06-021-2/+2
* asurada: update base sensor rotate matrixTing Shen2020-06-021-3/+2
* voxel: Initial EC imageDavid Wu2020-06-029-0/+1237
* Waddledee: Remove 5V input limit for board rev 1Diana Z2020-06-012-5/+4
* test: Add test for flash write protectionTom Hughes2020-05-304-0/+4
* test: Add flash_physical testTom Hughes2020-05-304-0/+4
* Waddledee: Set up C1 interrupt line for board rev 1Diana Z2020-05-302-5/+15
* waddledee/waddledoo: Mark BC1.2 as always poweredAseda Aboagye2020-05-292-0/+4
* baseboard/kukui: move bitbang stability fix to common codeTing Shen2020-05-291-74/+0
* bc12: create bc12 driver structureTing Shen2020-05-292-10/+0
* asurada: enable bmi160/bmm150Ting Shen2020-05-293-3/+117
* Lazor: Rename GPIO USB_A_CDP_ILIM_ENWai-Hong Tam2020-05-291-1/+1
* berknip: implement LED behaviorZick Wei2020-05-283-41/+178
* Bobba: New sku id 27 for Sparky360 (no pen)Sue2020-05-281-2/+6
* kappa: implement battery_get_vendor_param to return oemdataTing Shen2020-05-282-0/+22
* morphius: add thermal ic power on/offZick Wei2020-05-281-0/+1
* Puff: Increase I2C bus speed to 400KHzAndrew McRae2020-05-281-5/+5
* Puff: Clear the PD saved state if TCPC is resetAndrew McRae2020-05-281-0/+4
* test: Add scratchpad testTom Hughes2020-05-274-0/+4
* terrador: Initial EC imageDavid Wu2020-05-279-0/+1237
* Extend the tcpci register dump.Andrew McRae2020-05-272-2/+2
* servo_v4: clear SrcCap on CHG port disconnectedEric Yilun Lin2020-05-271-0/+8
* servo_v4: use PD_PREFER_HIGH_VOLTAGE for PDO selection logicEric Yilun Lin2020-05-271-0/+9
* jslrvp_ite: increase the chipset task stackSooraj Govindan2020-05-271-1/+1
* kukui: pull up SPI1_NSS (CS_L).Eric Yilun Lin2020-05-257-7/+7
* test: Add on-device MPU unit testTom Hughes2020-05-224-0/+4
* Puff: Use direct input for recovery button.Andrew McRae2020-05-223-25/+40
* Trembyle: Adjust fan speeds and tempsEdward Hill2020-05-211-11/+11
* berknip: add redriver TUSB544 and PS8743Zick Wei2020-05-212-157/+104
* Trembyle: Power off PS8811 retimer in S3Edward Hill2020-05-211-2/+2
* Trogdor: Fix the current limitation of USB Type-A portWai-Hong Tam2020-05-212-2/+2
* TCPMv2: Only include PD3.0 functionality when CONFIG_USB_PD_REV30Sam Hurst2020-05-214-2/+8
* volteer: correct lid g-sensor orientationKeith Short2020-05-211-3/+3
* waddledoo: Add rotation matrices for sensorsAseda Aboagye2020-05-211-3/+16
* Waddledoo: configure ECH1_PACKET_MODEDiana Z2020-05-211-8/+9
* Waddledee: configure ECH1_PACKET_MODEDiana Z2020-05-211-0/+1
* nightfury : blink charge led on low batteryYongBeum.Ha2020-05-201-2/+3
* Mushu : correct the GPU power leakage.loganliao2020-05-201-2/+0
* Mushu : Hibernate fail correct.loganliao2020-05-201-3/+2
* asurada rev0: Set GPM input level to 1.8V.Tony Lin2020-05-201-0/+3
* asurada: Enable PWM channel 0 control for power LED on sub-board.Ayo Wu2020-05-202-0/+10
* PD: Remove unnecessary PDCMD taskDiana Z2020-05-2068-68/+0
* PD: Pull EC_CMD_PD_HOST_EVENT_STATUS into common codeDiana Z2020-05-201-35/+0
* Ezkinil: Setting input current limit to 95%Sue2020-05-201-0/+15
* cortex-m: provide a function to set IRQ priorityPeter Marheine2020-05-191-12/+2
* Mushu : Fan1 rpm config.loganliao2020-05-181-5/+5
* Lazor: Correct the lid g-sensor's matrix configurationWai-Hong Tam2020-05-161-3/+3
View Lorry Controller Status