path: root/board/terrador/board.c

/* Copyright 2020 The Chromium OS Authors. All rights reserved.
 * Use of this source code is governed by a BSD-style license that can be
 * found in the LICENSE file.
 */

/* Volteer board-specific configuration */
#include "bb_retimer.h"
#include "button.h"
#include "common.h"
#include "accelgyro.h"
#include "cbi_ec_fw_config.h"
#include "driver/accel_bma2x2.h"
#include "driver/accelgyro_bmi260.h"
#include "driver/bc12/pi3usb9201.h"
#include "driver/als_tcs3400.h"
#include "driver/ppc/syv682x.h"
#include "driver/tcpm/tcpci.h"
#include "driver/tcpm/tusb422.h"
#include "driver/retimer/bb_retimer.h"
#include "driver/sync.h"
#include "extpower.h"
#include "fan.h"
#include "fan_chip.h"
#include "gpio.h"
#include "hooks.h"
#include "keyboard_scan.h"
#include "lid_switch.h"
#include "power.h"
#include "power_button.h"
#include "pwm.h"
#include "pwm_chip.h"
#include "switch.h"
#include "system.h"
#include "task.h"
#include "tablet_mode.h"
#include "throttle_ap.h"
#include "uart.h"
#include "usb_mux.h"
#include "usb_pd.h"
#include "usb_pd_tbt.h"
#include "usb_pd_tcpm.h"
#include "usbc_ppc.h"
#include "util.h"

#include "gpio_list.h" /* Must come after other header files. */

#define CPRINTS(format, args...) cprints(CC_CHIPSET, format, ## args)

/* Keyboard scan setting */
struct keyboard_scan_config keyscan_config = {
	/* Increase from 50 us, because KSO_02 passes through the H1. */
	.output_settle_us = 80,
	/* Other values should be the same as the default configuration. */
	.debounce_down_us = 9 * MSEC,
	.debounce_up_us = 30 * MSEC,
	.scan_period_us = 3 * MSEC,
	.min_post_scan_delay_us = 1000,
	.poll_timeout_us = 100 * MSEC,
	.actual_key_mask = {
		0x14, 0xff, 0xff, 0xff, 0xff, 0xf5, 0xff,
		0xa4, 0xff, 0xfe, 0x55, 0xfa, 0xca  /* full set */
	},
};

/******************************************************************************/
/*
 * FW_CONFIG defaults for Terrador if the CBI data is not initialized.
 */
union volteer_cbi_fw_config fw_config_defaults = {
	.usb_db = DB_USB3_PASSIVE,
};

static void board_init(void)
{

}
DECLARE_HOOK(HOOK_INIT, board_init, HOOK_PRIO_DEFAULT);

/******************************************************************************/
/* I2C port map configuration */
const struct i2c_port_t i2c_ports[] = {
	{
		.name = "sensor",
		.port = I2C_PORT_SENSOR,
		.kbps = 400,
		.scl = GPIO_EC_I2C0_SENSOR_SCL,
		.sda = GPIO_EC_I2C0_SENSOR_SDA,
	},
	{
		.name = "usb_c0",
		.port = I2C_PORT_USB_C0,
		.kbps = 1000,
		.scl = GPIO_EC_I2C1_USB_C0_SCL,
		.sda = GPIO_EC_I2C1_USB_C0_SDA,
	},
	{
		.name = "usb_c1",
		.port = I2C_PORT_USB_C1,
		.kbps = 1000,
		.scl = GPIO_EC_I2C2_USB_C1_SCL,
		.sda = GPIO_EC_I2C2_USB_C1_SDA,
	},
	{
		.name = "usb_0_mix",
		.port = I2C_PORT_USB_0_MIX,
		.kbps = 100,
		.scl = GPIO_EC_I2C3_USB_0_MIX_SCL,
		.sda = GPIO_EC_I2C3_USB_0_MIX_SDA,
	},
	{
		.name = "usb_1_mix",
		.port = I2C_PORT_USB_1_MIX,
		.kbps = 100,
		.scl = GPIO_EC_I2C4_USB_1_MIX_SCL,
		.sda = GPIO_EC_I2C4_USB_1_MIX_SDA,
	},
	{
		.name = "power",
		.port = I2C_PORT_POWER,
		.kbps = 100,
		.scl = GPIO_EC_I2C5_POWER_SCL,
		.sda = GPIO_EC_I2C5_POWER_SDA,
	},
	{
		.name = "eeprom",
		.port = I2C_PORT_EEPROM,
		.kbps = 400,
		.scl = GPIO_EC_I2C7_EEPROM_SCL,
		.sda = GPIO_EC_I2C7_EEPROM_SDA,
	},
};
const unsigned int i2c_ports_used = ARRAY_SIZE(i2c_ports);

/******************************************************************************/
/* PWM configuration */
const struct pwm_t pwm_channels[] = {
	[PWM_CH_LED1_BLUE] = {
		.channel = 2,
		.flags = PWM_CONFIG_ACTIVE_LOW | PWM_CONFIG_DSLEEP,
		.freq = 2400,
	},
	[PWM_CH_LED2_RED] = {
		.channel = 0,
		.flags = PWM_CONFIG_ACTIVE_LOW | PWM_CONFIG_DSLEEP,
		.freq = 2400,
	},
	[PWM_CH_LED3_GREEN] = {
		.channel = 1,
		.flags = PWM_CONFIG_ACTIVE_LOW | PWM_CONFIG_DSLEEP,
		.freq = 2400,
	},
	[PWM_CH_KBLIGHT] = {
		.channel = 3,
		.flags = 0,
		/*
		 * Set PWM frequency to multiple of 50 Hz and 60 Hz to prevent
		 * flicker. Higher frequencies consume similar average power to
		 * lower PWM frequencies, but higher frequencies record a much
		 * lower maximum power.
		 */
		.freq = 2400,
	},
};
BUILD_ASSERT(ARRAY_SIZE(pwm_channels) == PWM_CH_COUNT);

/******************************************************************************/
/* EC thermal management configuration */

/*
 * Tiger Lake specifies 100 C as maximum TDP temperature.  THRMTRIP# occurs at
 * 130 C.  However, sensor is located next to DDR, so we need to use the lower
 * DDR temperature limit (85 C)
 */
const static struct ec_thermal_config thermal_cpu = {
	.temp_host = {
		[EC_TEMP_THRESH_HIGH] = C_TO_K(70),
		[EC_TEMP_THRESH_HALT] = C_TO_K(80),
	},
	.temp_host_release = {
		[EC_TEMP_THRESH_HIGH] = C_TO_K(65),
	},
	.temp_fan_off = C_TO_K(35),
	.temp_fan_max = C_TO_K(50),
};

/*
 * Inductor limits - used for both charger and PP3300 regulator
 *
 * Need to use the lower of the charger IC, PP3300 regulator, and the inductors
 *
 * Charger max recommended temperature 100C, max absolute temperature 125C
 * PP3300 regulator: operating range -40 C to 145 C
 *
 * Inductors: limit of 125c
 * PCB: limit is 80c
 */
const static struct ec_thermal_config thermal_inductor = {
	.temp_host = {
		[EC_TEMP_THRESH_HIGH] = C_TO_K(75),
		[EC_TEMP_THRESH_HALT] = C_TO_K(80),
	},
	.temp_host_release = {
		[EC_TEMP_THRESH_HIGH] = C_TO_K(65),
	},
	.temp_fan_off = C_TO_K(40),
	.temp_fan_max = C_TO_K(55),
};


struct ec_thermal_config thermal_params[] = {
	[TEMP_SENSOR_1_CHARGER]			= thermal_inductor,
	[TEMP_SENSOR_2_PP3300_REGULATOR]	= thermal_inductor,
	[TEMP_SENSOR_3_DDR_SOC]			= thermal_cpu,
	[TEMP_SENSOR_4_FAN]			= thermal_cpu,
};
BUILD_ASSERT(ARRAY_SIZE(thermal_params) == TEMP_SENSOR_COUNT);

/******************************************************************************/

static void kb_backlight_enable(void)
{
	gpio_set_level(GPIO_EC_KB_BL_EN, 1);
}
DECLARE_HOOK(HOOK_CHIPSET_RESUME, kb_backlight_enable, HOOK_PRIO_DEFAULT);

static void kb_backlight_disable(void)
{
	gpio_set_level(GPIO_EC_KB_BL_EN, 0);
}
DECLARE_HOOK(HOOK_CHIPSET_SUSPEND, kb_backlight_disable, HOOK_PRIO_DEFAULT);

void board_reset_pd_mcu(void)
{
	/* TODO(b/159025015): Terrador: check USB PD reset operation */
}

/* USBC mux configuration - Tiger Lake includes internal mux */
struct usb_mux usbc0_usb4_mb_retimer = {
	.usb_port = USBC_PORT_C0,
	.driver = &bb_usb_retimer,
	.i2c_port = I2C_PORT_USB_0_MIX,
	.i2c_addr_flags = USBC_PORT_C0_BB_RETIMER_I2C_ADDR,
};
/*****************************************************************************
 * USB-C MUX/Retimer dynamic configuration.
 */
static void setup_mux(void)
{
	CPRINTS("C0 supports bb-retimer");
	/* USB-C port 0 have a retimer */
	usb_muxes[USBC_PORT_C0].next_mux = &usbc0_usb4_mb_retimer;
}

__override void board_cbi_init(void)
{
	/*
	 * TODO(b/159025015): Terrador: check FW_CONFIG fields for USB DB type
	 */
	setup_mux();
	/* Reassign USB_C0_RT_RST_ODL */
	bb_controls[USBC_PORT_C0].usb_ls_en_gpio = GPIO_USB_C0_LS_EN;
	bb_controls[USBC_PORT_C0].retimer_rst_gpio = GPIO_USB_C0_RT_RST_ODL;

}

/******************************************************************************/
/* USBC PPC configuration */
struct ppc_config_t ppc_chips[] = {
	[USBC_PORT_C0] = {
		.i2c_port = I2C_PORT_USB_C0,
		.i2c_addr_flags = SYV682X_ADDR0_FLAGS,
		.drv = &syv682x_drv,
	},
	[USBC_PORT_C1] = {
		.i2c_port = I2C_PORT_USB_C1,
		.i2c_addr_flags = SYV682X_ADDR0_FLAGS,
		.drv = &syv682x_drv,
	},
};
BUILD_ASSERT(ARRAY_SIZE(ppc_chips) == USBC_PORT_COUNT);
unsigned int ppc_cnt = ARRAY_SIZE(ppc_chips);

/******************************************************************************/
/* PPC support routines */
void ppc_interrupt(enum gpio_signal signal)
{
	switch (signal) {
	case GPIO_USB_C0_PPC_INT_ODL:
		syv682x_interrupt(USBC_PORT_C0);
		break;
	case GPIO_USB_C1_PPC_INT_ODL:
		syv682x_interrupt(USBC_PORT_C1);
	default:
		break;
	}
}

/******************************************************************************/
/* BC1.2 charger detect configuration */
const struct pi3usb9201_config_t pi3usb9201_bc12_chips[] = {
	[USBC_PORT_C0] = {
		.i2c_port = I2C_PORT_USB_C0,
		.i2c_addr_flags = PI3USB9201_I2C_ADDR_3_FLAGS,
	},
	[USBC_PORT_C1] = {
		.i2c_port = I2C_PORT_USB_C1,
		.i2c_addr_flags = PI3USB9201_I2C_ADDR_3_FLAGS,
	},
};
BUILD_ASSERT(ARRAY_SIZE(pi3usb9201_bc12_chips) == USBC_PORT_COUNT);

/******************************************************************************/
/* USBC TCPC configuration */
struct tcpc_config_t tcpc_config[] = {
	[USBC_PORT_C0] = {
		.bus_type = EC_BUS_TYPE_I2C,
		.i2c_info = {
			.port = I2C_PORT_USB_C0,
			.addr_flags = TUSB422_I2C_ADDR_FLAGS,
		},
		.drv = &tusb422_tcpm_drv,
	},
	[USBC_PORT_C1] = {
		.bus_type = EC_BUS_TYPE_I2C,
		.i2c_info = {
			.port = I2C_PORT_USB_C1,
			.addr_flags = TUSB422_I2C_ADDR_FLAGS,
		},
		.drv = &tusb422_tcpm_drv,
	},
};
BUILD_ASSERT(ARRAY_SIZE(tcpc_config) == USBC_PORT_COUNT);
BUILD_ASSERT(CONFIG_USB_PD_PORT_MAX_COUNT == USBC_PORT_COUNT);

/******************************************************************************/
/* USBC mux configuration - Tiger Lake includes internal mux */
struct usb_mux usbc1_tcss_usb_mux = {
	.usb_port = USBC_PORT_C1,
	.driver = &virtual_usb_mux_driver,
	.hpd_update = &virtual_hpd_update,
};
struct usb_mux usb_muxes[] = {
	[USBC_PORT_C0] = {
		.usb_port = USBC_PORT_C0,
		.driver = &virtual_usb_mux_driver,
		.hpd_update = &virtual_hpd_update,
	},
	[USBC_PORT_C1] = {
		.usb_port = USBC_PORT_C1,
		.next_mux = &usbc1_tcss_usb_mux,
		.driver = &bb_usb_retimer,
		.i2c_port = I2C_PORT_USB_1_MIX,
		.i2c_addr_flags = USBC_PORT_C1_BB_RETIMER_I2C_ADDR,
	},
};
BUILD_ASSERT(ARRAY_SIZE(usb_muxes) == USBC_PORT_COUNT);

struct bb_usb_control bb_controls[] = {
	[USBC_PORT_C0] = {
		/* USB-C port 0 doesn't have a retimer */
	},
	[USBC_PORT_C1] = {
		.usb_ls_en_gpio = GPIO_USB_C1_LS_EN,
		.retimer_rst_gpio = GPIO_USB_C1_RT_RST_ODL,
	},
};
BUILD_ASSERT(ARRAY_SIZE(bb_controls) == USBC_PORT_COUNT);

static void board_tcpc_init(void)
{
	/* Don't reset TCPCs after initial reset */
	if (!system_jumped_late())
		board_reset_pd_mcu();

	/* Enable PPC interrupts. */
	gpio_enable_interrupt(GPIO_USB_C0_PPC_INT_ODL);
	gpio_enable_interrupt(GPIO_USB_C1_PPC_INT_ODL);

	/* Enable TCPC interrupts. */
	gpio_enable_interrupt(GPIO_USB_C0_TCPC_INT_ODL);
	gpio_enable_interrupt(GPIO_USB_C1_TCPC_INT_ODL);

	/* Enable BC1.2 interrupts. */
	gpio_enable_interrupt(GPIO_USB_C0_BC12_INT_ODL);
	gpio_enable_interrupt(GPIO_USB_C1_BC12_INT_ODL);
}
DECLARE_HOOK(HOOK_INIT, board_tcpc_init, HOOK_PRIO_INIT_CHIPSET);

/******************************************************************************/
/* TCPC support routines */
uint16_t tcpc_get_alert_status(void)
{
	uint16_t status = 0;

	/*
	 * Check which port has the ALERT line set
	 */
	if (!gpio_get_level(GPIO_USB_C0_TCPC_INT_ODL))
		status |= PD_STATUS_TCPC_ALERT_0;
	if (!gpio_get_level(GPIO_USB_C1_TCPC_INT_ODL))
		status |= PD_STATUS_TCPC_ALERT_1;

	return status;
}

int ppc_get_alert_status(int port)
{
	if (port == USBC_PORT_C0)
		return gpio_get_level(GPIO_USB_C0_PPC_INT_ODL) == 0;
	else
		return gpio_get_level(GPIO_USB_C1_PPC_INT_ODL) == 0;
}

/******************************************************************************/
/* USB-A charging control */

const int usb_port_enable[USB_PORT_COUNT] = {
	GPIO_EN_PP5000_USBA,
};