path: root/board/vilboz/board.c

/* Copyright 2020 The Chromium OS Authors. All rights reserved.
 * Use of this source code is governed by a BSD-style license that can be
 * found in the LICENSE file.
 */

#include "battery_smart.h"
#include "button.h"
#include "cros_board_info.h"
#include "driver/accel_lis2dw12.h"
#include "driver/accelgyro_lsm6dsm.h"
#include "driver/bc12/pi3usb9201.h"
#include "driver/ioexpander/pcal6408.h"
#include "driver/ppc/aoz1380.h"
#include "driver/tcpm/nct38xx.h"
#include "driver/usb_mux/amd_fp5.h"
#include "extpower.h"
#include "fan.h"
#include "fan_chip.h"
#include "gpio.h"
#include "hooks.h"
#include "lid_switch.h"
#include "power.h"
#include "power_button.h"
#include "pwm.h"
#include "pwm_chip.h"
#include "switch.h"
#include "system.h"
#include "tablet_mode.h"
#include "task.h"
#include "usb_charge.h"
#include "usb_pd_tcpm.h"
#include "usb_mux.h"
#include "usbc_ppc.h"

#define CPRINTSUSB(format, args...) cprints(CC_USBCHARGE, format, ## args)
#define CPRINTFUSB(format, args...) cprintf(CC_USBCHARGE, format, ## args)

/* This I2C moved. Temporarily detect and support the V0 HW. */
int I2C_PORT_BATTERY = I2C_PORT_BATTERY_V1;

void hdmi_hpd_interrupt(enum gpio_signal signal)
{
	gpio_set_level(GPIO_DP1_HPD, gpio_get_level(signal));
}

#include "gpio_list.h"

#ifdef HAS_TASK_MOTIONSENSE

/* Motion sensors */
static struct mutex g_lid_mutex;
static struct mutex g_base_mutex;

/* sensor private data */
static struct stprivate_data g_lis2dwl_data;
static struct lsm6dsm_data g_lsm6dsm_data = LSM6DSM_DATA;

/* Matrix to rotate accelrator into standard reference frame */
static const mat33_fp_t base_standard_ref = {
	{ FLOAT_TO_FP(-1), 0, 0},
	{ 0, FLOAT_TO_FP(-1), 0},
	{ 0, 0, FLOAT_TO_FP(1)}
};

static const mat33_fp_t lid_standard_ref = {
	{ FLOAT_TO_FP(1), 0, 0},
	{ 0, FLOAT_TO_FP(-1), 0},
	{ 0, 0, FLOAT_TO_FP(-1)}
};

/* TODO(gcc >= 5.0) Remove the casts to const pointer at rot_standard_ref */
struct motion_sensor_t motion_sensors[] = {
	[LID_ACCEL] = {
	 .name = "Lid Accel",
	 .active_mask = SENSOR_ACTIVE_S0_S3,
	 .chip = MOTIONSENSE_CHIP_LIS2DWL,
	 .type = MOTIONSENSE_TYPE_ACCEL,
	 .location = MOTIONSENSE_LOC_LID,
	 .drv = &lis2dw12_drv,
	 .mutex = &g_lid_mutex,
	 .drv_data = &g_lis2dwl_data,
	 .port = I2C_PORT_SENSOR,
	 .i2c_spi_addr_flags = LIS2DWL_ADDR1_FLAGS,
	 .rot_standard_ref = &lid_standard_ref,
	 .default_range = 2, /* g, enough for laptop. */
	 .min_frequency = LIS2DW12_ODR_MIN_VAL,
	 .max_frequency = LIS2DW12_ODR_MAX_VAL,
	 .config = {
		 /* EC use accel for angle detection */
		[SENSOR_CONFIG_EC_S0] = {
			.odr = 12500 | ROUND_UP_FLAG,
		},
		 /* Sensor on for lid angle detection */
		[SENSOR_CONFIG_EC_S3] = {
			.odr = 10000 | ROUND_UP_FLAG,
		},
	},
	},

	[BASE_ACCEL] = {
	 .name = "Base Accel",
	 .active_mask = SENSOR_ACTIVE_S0_S3,
	 .chip = MOTIONSENSE_CHIP_LSM6DSM,
	 .type = MOTIONSENSE_TYPE_ACCEL,
	 .location = MOTIONSENSE_LOC_BASE,
	 .drv = &lsm6dsm_drv,
	 .mutex = &g_base_mutex,
	 .drv_data = LSM6DSM_ST_DATA(g_lsm6dsm_data,
			MOTIONSENSE_TYPE_ACCEL),
	 .int_signal = GPIO_6AXIS_INT_L,
	 .flags = MOTIONSENSE_FLAG_INT_SIGNAL,
	 .port = I2C_PORT_SENSOR,
	 .i2c_spi_addr_flags = LSM6DSM_ADDR0_FLAGS,
	 .default_range = 4, /* g, enough for laptop */
	 .rot_standard_ref = &base_standard_ref,
	 .min_frequency = LSM6DSM_ODR_MIN_VAL,
	 .max_frequency = LSM6DSM_ODR_MAX_VAL,
	 .config = {
		 /* EC use accel for angle detection */
		[SENSOR_CONFIG_EC_S0] = {
			.odr = 13000 | ROUND_UP_FLAG,
			.ec_rate = 100 * MSEC,
		},
		/* Sensor on for angle detection */
		[SENSOR_CONFIG_EC_S3] = {
			.odr = 10000 | ROUND_UP_FLAG,
			.ec_rate = 100 * MSEC,
		},
	 },
	},

	[BASE_GYRO] = {
	 .name = "Base Gyro",
	 .active_mask = SENSOR_ACTIVE_S0_S3,
	 .chip = MOTIONSENSE_CHIP_LSM6DSM,
	 .type = MOTIONSENSE_TYPE_GYRO,
	 .location = MOTIONSENSE_LOC_BASE,
	 .drv = &lsm6dsm_drv,
	 .mutex = &g_base_mutex,
	 .drv_data = LSM6DSM_ST_DATA(g_lsm6dsm_data,
			MOTIONSENSE_TYPE_GYRO),
	.int_signal = GPIO_6AXIS_INT_L,
	.flags = MOTIONSENSE_FLAG_INT_SIGNAL,
	 .port = I2C_PORT_SENSOR,
	 .i2c_spi_addr_flags = LSM6DSM_ADDR0_FLAGS,
	 .default_range = 1000 | ROUND_UP_FLAG, /* dps */
	 .rot_standard_ref = &base_standard_ref,
	 .min_frequency = LSM6DSM_ODR_MIN_VAL,
	 .max_frequency = LSM6DSM_ODR_MAX_VAL,
	},
};

unsigned int motion_sensor_count = ARRAY_SIZE(motion_sensors);

#endif /* HAS_TASK_MOTIONSENSE */

/*
 * USB C0 port SBU mux use standalone FSUSB42UMX
 * chip and it need a board specific driver.
 * Overall, it will use chained mux framework.
 */
static int fsusb42umx_set_mux(const struct usb_mux *me, mux_state_t mux_state)
{
	if (mux_state & USB_PD_MUX_POLARITY_INVERTED)
		ioex_set_level(IOEX_USB_C0_SBU_FLIP, 1);
	else
		ioex_set_level(IOEX_USB_C0_SBU_FLIP, 0);

	return EC_SUCCESS;
}

/*
 * .init is not necessary here because it has nothing
 * to do. Primary mux will handle mux state so .get is
 * not needed as well. usb_mux.c can handle the situation
 * properly.
 */
const struct usb_mux_driver usbc0_sbu_mux_driver = {
	.set = fsusb42umx_set_mux,
};

/*
 * Since FSUSB42UMX is not a i2c device, .i2c_port and
 * .i2c_addr_flags are not required here.
 */
const struct usb_mux usbc0_sbu_mux = {
	.usb_port = USBC_PORT_C0,
	.driver = &usbc0_sbu_mux_driver,
};

const struct usb_mux usb_muxes[] = {
	[USBC_PORT_C0] = {
		.usb_port = USBC_PORT_C0,
		.i2c_port = I2C_PORT_USB_AP_MUX,
		.i2c_addr_flags = AMD_FP5_MUX_I2C_ADDR_FLAGS,
		.driver = &amd_fp5_usb_mux_driver,
		.next_mux = &usbc0_sbu_mux,
	},
};
BUILD_ASSERT(ARRAY_SIZE(usb_muxes) == USBC_PORT_COUNT);

struct ppc_config_t ppc_chips[] = {
	[USBC_PORT_C0] = {
		/* Device does not talk I2C */
		.drv = &aoz1380_drv
	},
};
BUILD_ASSERT(ARRAY_SIZE(ppc_chips) == USBC_PORT_COUNT);
unsigned int ppc_cnt = ARRAY_SIZE(ppc_chips);

void ppc_interrupt(enum gpio_signal signal)
{
	switch (signal) {
	case GPIO_USB_C0_PPC_FAULT_ODL:
		aoz1380_interrupt(USBC_PORT_C0);
		break;

	default:
		break;
	}
}

int board_set_active_charge_port(int port)
{
	int is_valid_port = (port >= 0 &&
			     port < CONFIG_USB_PD_PORT_MAX_COUNT);
	int i;

	if (port == CHARGE_PORT_NONE) {
		CPRINTSUSB("Disabling all charger ports");

		/* Disable all ports. */
		for (i = 0; i < ppc_cnt; i++) {
			/*
			 * Do not return early if one fails otherwise we can
			 * get into a boot loop assertion failure.
			 */
			if (ppc_vbus_sink_enable(i, 0))
				CPRINTSUSB("Disabling C%d as sink failed.", i);
		}

		return EC_SUCCESS;
	} else if (!is_valid_port) {
		return EC_ERROR_INVAL;
	}


	/* Check if the port is sourcing VBUS. */
	if (ppc_is_sourcing_vbus(port)) {
		CPRINTFUSB("Skip enable C%d", port);
		return EC_ERROR_INVAL;
	}

	CPRINTSUSB("New charge port: C%d", port);

	/*
	 * Turn off the other ports' sink path FETs, before enabling the
	 * requested charge port.
	 */
	for (i = 0; i < ppc_cnt; i++) {
		if (i == port)
			continue;

		if (ppc_vbus_sink_enable(i, 0))
			CPRINTSUSB("C%d: sink path disable failed.", i);
	}

	/* Enable requested charge port. */
	if (ppc_vbus_sink_enable(port, 1)) {
		CPRINTSUSB("C%d: sink path enable failed.", port);
		return EC_ERROR_UNKNOWN;
	}

	return EC_SUCCESS;
}

void board_overcurrent_event(int port, int is_overcurrented)
{
	switch (port) {
	case USBC_PORT_C0:
		ioex_set_level(IOEX_USB_C0_FAULT_ODL, !is_overcurrented);
		break;

	default:
		break;
	}
}

const struct tcpc_config_t tcpc_config[] = {
	[USBC_PORT_C0] = {
		.bus_type = EC_BUS_TYPE_I2C,
		.i2c_info = {
			.port = I2C_PORT_TCPC0,
			.addr_flags = NCT38XX_I2C_ADDR1_1_FLAGS,
		},
		.drv = &nct38xx_tcpm_drv,
		.flags = TCPC_FLAGS_TCPCI_REV2_0,
	},
};
BUILD_ASSERT(ARRAY_SIZE(tcpc_config) == USBC_PORT_COUNT);
BUILD_ASSERT(CONFIG_USB_PD_PORT_MAX_COUNT == USBC_PORT_COUNT);

const struct pi3usb9201_config_t pi3usb9201_bc12_chips[] = {
	[USBC_PORT_C0] = {
		.i2c_port = I2C_PORT_TCPC0,
		.i2c_addr_flags = PI3USB9201_I2C_ADDR_3_FLAGS,
	},
};
BUILD_ASSERT(ARRAY_SIZE(pi3usb9201_bc12_chips) == USBC_PORT_COUNT);

static void reset_pd_port(int port, enum gpio_signal reset_gpio_l,
			  int hold_delay, int finish_delay)
{
	gpio_set_level(reset_gpio_l, 0);
	msleep(hold_delay);
	gpio_set_level(reset_gpio_l, 1);
	if (finish_delay)
		msleep(finish_delay);
}

void board_reset_pd_mcu(void)
{
	/* Reset TCPC0 */
	reset_pd_port(USBC_PORT_C0, GPIO_USB_C0_TCPC_RST_L,
		      NCT38XX_RESET_HOLD_DELAY_MS,
		      NCT38XX_RESET_POST_DELAY_MS);

}

uint16_t tcpc_get_alert_status(void)
{
	uint16_t status = 0;

	/*
	 * Check which port has the ALERT line set and ignore if that TCPC has
	 * its reset line active.
	 */
	if (!gpio_get_level(GPIO_USB_C0_TCPC_INT_ODL)) {
		if (gpio_get_level(GPIO_USB_C0_TCPC_RST_L) != 0)
			status |= PD_STATUS_TCPC_ALERT_0;
	}

	return status;
}

void tcpc_alert_event(enum gpio_signal signal)
{
	int port = -1;

	switch (signal) {
	case GPIO_USB_C0_TCPC_INT_ODL:
		port = 0;
		break;
	default:
		return;
	}

	schedule_deferred_pd_interrupt(port);
}

int board_pd_set_frs_enable(int port, int enable)
{
	int rv = EC_SUCCESS;

	/* Use the TCPC to enable fast switch when FRS included */
	if (port == USBC_PORT_C0) {
		rv = ioex_set_level(IOEX_USB_C0_TCPC_FASTSW_CTL_EN,
				    !!enable);
	}

	return rv;
}

void bc12_interrupt(enum gpio_signal signal)
{
	switch (signal) {
	case GPIO_USB_C0_BC12_INT_ODL:
		task_set_event(TASK_ID_USB_CHG_P0, USB_CHG_EVENT_BC12, 0);
		break;

	default:
		break;
	}
}

static void setup_fw_config(void)
{
	/* Enable DB HDMI interrupts. */
	gpio_enable_interrupt(GPIO_HDMI_CONN_HPD_3V3);

	/* Enable PPC interrupts. */
	gpio_enable_interrupt(GPIO_USB_C0_PPC_FAULT_ODL);

	/* Enable TCPC interrupts. */
	gpio_enable_interrupt(GPIO_USB_C0_TCPC_INT_ODL);

	/* Enable BC 1.2 interrupts */
	gpio_enable_interrupt(GPIO_USB_C0_BC12_INT_ODL);

	/* Enable SBU fault interrupts */
	ioex_enable_interrupt(IOEX_USB_C0_SBU_FAULT_ODL);

	if (ec_config_has_lid_angle_tablet_mode()) {
		/* Enable Gyro interrupts */
		gpio_enable_interrupt(GPIO_6AXIS_INT_L);
	} else {
		motion_sensor_count = 0;
		/* Device is clamshell only */
		tablet_set_mode(0);
		/* Gyro is not present, don't allow line to float */
		gpio_set_flags(GPIO_6AXIS_INT_L, GPIO_INPUT | GPIO_PULL_DOWN);
	}
}
DECLARE_HOOK(HOOK_INIT, setup_fw_config, HOOK_PRIO_INIT_I2C + 2);

static void wwan_lte_startup(void)
{
	/* Turn on WWAN LTE function as we go into S0 from S5. */
	gpio_set_level(GPIO_LTE_EN, 1);
	gpio_set_level(GPIO_LTE_W_DISABLE_L, 1);
}
DECLARE_HOOK(HOOK_CHIPSET_STARTUP, wwan_lte_startup, HOOK_PRIO_DEFAULT + 1);

static void wwan_lte_shutdown(void)
{
	/* Turn off WWAN LTE function as we go back to S5. */
	gpio_set_level(GPIO_LTE_EN, 0);
	gpio_set_level(GPIO_LTE_W_DISABLE_L, 0);
}
DECLARE_HOOK(HOOK_CHIPSET_SHUTDOWN, wwan_lte_shutdown, HOOK_PRIO_DEFAULT + 1);

const struct pwm_t pwm_channels[] = {
	[PWM_CH_KBLIGHT] = {
		.channel = 3,
		.flags = PWM_CONFIG_DSLEEP,
		.freq = 100,
	},
};
BUILD_ASSERT(ARRAY_SIZE(pwm_channels) == PWM_CH_COUNT);

struct ioexpander_config_t ioex_config[] = {
	[IOEX_C0_NCT3807] = {
		.i2c_host_port = I2C_PORT_TCPC0,
		.i2c_slave_addr = NCT38XX_I2C_ADDR1_1_FLAGS,
		.drv = &nct38xx_ioexpander_drv,
	},
};
BUILD_ASSERT(ARRAY_SIZE(ioex_config) == CONFIG_IO_EXPANDER_PORT_COUNT);

const int usb_port_enable[USBA_PORT_COUNT] = {
	IOEX_EN_USB_A0_5V,
	GPIO_EN_USB_A1_5V,
};