1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
|
/* Copyright (c) 2012 The Chromium OS Authors. All rights reserved.
* Use of this source code is governed by a BSD-style license that can be
* found in the LICENSE file.
*/
/* SPI interface for Chrome EC */
#ifndef __CROS_EC_SPI_H
#define __CROS_EC_SPI_H
/*
* SPI Clock polarity and phase mode (0 - 3)
* @code
* clk mode | POL PHA
* ---------+--------
* 0 | 0 0
* 1 | 0 1
* 2 | 1 0
* 3 | 1 1
* ---------+--------
* @endcode
*/
enum spi_clock_mode {
SPI_CLOCK_MODE0 = 0,
SPI_CLOCK_MODE1 = 1,
SPI_CLOCK_MODE2 = 2,
SPI_CLOCK_MODE3 = 3
};
struct spi_device_t {
/*
* SPI port the device is connected to.
* On some architecture, this is SPI master port index,
* on other the SPI port index directly.
*/
uint8_t port;
/*
* Clock divisor to talk to SPI device.
* If several devices share the same port, we select the lowest speed.
*/
uint8_t div;
/* gpio used for chip selection. */
enum gpio_signal gpio_cs;
};
extern const struct spi_device_t spi_devices[];
extern const unsigned int spi_devices_used;
/*
* The first port in spi_devices defines the port to access the SPI flash.
* The first gpio defines the CS GPIO to access the flash,
* if used.
*/
#define SPI_FLASH_DEVICE (&spi_devices[0])
/*
* Enable / disable the SPI port. When the port is disabled, all its I/O lines
* are high-Z so the EC won't interfere with other devices on the SPI bus.
*
* @param port port id to work on.
* @param enable 1 to enable the port, 0 to disable it.
*/
int spi_enable(int port, int enable);
/* Issue a SPI transaction. Assumes SPI port has already been enabled.
*
* Transmits <txlen> bytes from <txdata>, throwing away the corresponding
* received data, then transmits <rxlen> dummy bytes, saving the received data
* in <rxdata>.
*
* @param spi_device the SPI device to use
* @param txdata buffer to transmit
* @param txlen number of bytes in txdata.
* @param rxdata receive buffer.
* @param rxlen number of bytes in rxdata.
*/
int spi_transaction(const struct spi_device_t *spi_device,
const uint8_t *txdata, int txlen,
uint8_t *rxdata, int rxlen);
/* Similar to spi_transaction(), but hands over to DMA for reading response.
* Must call spi_transaction_flush() after this to make sure the response is
* received.
*/
int spi_transaction_async(const struct spi_device_t *spi_device,
const uint8_t *txdata, int txlen,
uint8_t *rxdata, int rxlen);
/* Wait for async response received */
int spi_transaction_flush(const struct spi_device_t *spi_device);
#ifdef CONFIG_SPI
/**
* Called when the NSS level changes, signalling the start or end of a SPI
* transaction.
*
* @param signal GPIO signal that changed
*/
void spi_event(enum gpio_signal signal);
#else
static inline void spi_event(enum gpio_signal signal)
{
}
#endif
#endif /* __CROS_EC_SPI_H */
|
