sbxxx: Set SPI clock to 16.5 MHz and disable fast reads.

Do not rely on broken firmware to set up the SPI configuration correctly.
Some boards fail with flashrom because the firmware chose too high speeds
for the alternate SPI mode which flashrom uses. Temporarily change the
clock to the lowest common value of 16.5 MHz.

Also, disable fast reads just to be safe.

Signed-off-by: Stefan Tauner <stefan.tauner@student.tuwien.ac.at>
Acked-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>

git-svn-id: https://code.coreboot.org/svn/flashrom/trunk@1750 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1

1 files changed, 63 insertions, 8 deletions

diff --git a/sb600spi.c b/sb600spi.c
index 8f93d65..9523591 100644
--- a/sb600spi.c
+++ b/sb600spi.c
@@ -272,6 +272,62 @@ static int sb600_spi_send_command(struct flashctx *flash, unsigned int writecnt,
 	return 0;
 }
 
+struct spispeed {
+	const char *const name;
+	const uint8_t speed;
+};
+
+static const struct spispeed spispeeds[] = {
+	{ "66 MHz",	0x00 },
+	{ "33 MHz",	0x01 },
+	{ "22 MHz",	0x02 },
+	{ "16.5 MHz",	0x03 },
+};
+
+static int set_speed(struct pci_dev *dev, const struct spispeed *spispeed)
+{
+	bool success = false;
+	uint8_t speed = spispeed->speed;
+
+	msg_pdbg("Setting SPI clock to %s (0x%x).\n", spispeed->name, speed);
+	if (amd_gen != CHIPSET_YANGTZE) {
+		rmmio_writeb((mmio_readb(sb600_spibar + 0xd) & ~(0x3 << 4)) | (speed << 4), sb600_spibar + 0xd);
+		success = (speed == ((mmio_readb(sb600_spibar + 0xd) >> 4) & 0x3));
+	}
+
+	if (!success) {
+		msg_perr("Setting SPI clock failed.\n");
+		return 1;
+	}
+	return 0;
+}
+
+static int handle_speed(struct pci_dev *dev)
+{
+	uint32_t tmp;
+	int8_t spispeed_idx = 3; /* Default to 16.5 MHz */
+
+	/* See the chipset support matrix for SPI Base_Addr below for an explanation of the symbols used.
+	 * bit   6xx   7xx/SP5100  8xx             9xx  hudson1  hudson234  yangtze
+	 * 18    rsvd  <-          fastReadEnable  ?    <-       ?          SpiReadMode[0]
+	 * 29:30 rsvd  <-          <-              ?    <-       ?          SpiReadMode[2:1]
+	 */
+	if (amd_gen != CHIPSET_YANGTZE) {
+		if (amd_gen >= CHIPSET_SB89XX && amd_gen <= CHIPSET_HUDSON234) {
+			bool fast_read = (mmio_readl(sb600_spibar + 0x00) >> 18) & 0x1;
+			msg_pdbg("Fast Reads are %sabled\n", fast_read ? "en" : "dis");
+			if (fast_read) {
+				msg_pdbg("Disabling them temporarily.\n");
+				rmmio_writel(mmio_readl(sb600_spibar + 0x00) & ~(0x1 << 18),
+					     sb600_spibar + 0x00);
+			}
+		}
+		tmp = (mmio_readb(sb600_spibar + 0xd) >> 4) & 0x3;
+		msg_pdbg("NormSpeed is %s\n", spispeeds[tmp].name);
+	}
+	return set_speed(dev, &spispeeds[spispeed_idx]);
+}
+
 static int sb600_handle_imc(struct pci_dev *dev, bool amd_imc_force)
 {
 	/* Handle IMC everywhere but sb600 which does not have one. */
@@ -322,9 +378,6 @@ int sb600_probe_spi(struct pci_dev *dev)
 	uint32_t tmp;
 	uint8_t reg;
 	bool amd_imc_force = false;
-	static const char *const speed_names[4] = {
-		"66/reserved", "33", "22", "16.5"
-	};
 
 	char *arg = extract_programmer_param("amd_imc_force");
 	if (arg && !strcmp(arg, "yes")) {
@@ -411,7 +464,7 @@ int sb600_probe_spi(struct pci_dev *dev)
 	 * See the chipset support matrix for SPI Base_Addr above for an explanation of the symbols used.
 	 * bit   6xx                7xx/SP5100      8xx               9xx  hudson1  hudson2+  yangtze
 	 * 17    rsvd               <-              <-                ?    <-       ?         <-
-	 * 18    rsvd               <-              fastReadEnable<1> ?    <-       ?         SpiReadMode[0]
+	 * 18    rsvd               <-              fastReadEnable<1> ?    <-       ?         SpiReadMode[0]<1>
 	 * 19    SpiArbEnable       <-              <-                ?    <-       ?         <-
 	 * 20    (FifoPtrClr)       <-              <-                ?    <-       ?         <-
 	 * 21    (FifoPtrInc)       <-              <-                ?    <-       ?         IllegalAccess
@@ -420,8 +473,10 @@ int sb600_probe_spi(struct pci_dev *dev)
 	 * 24:26 ArbWaitCount       <-              <-                ?    <-       ?         <-
 	 * 27    SpiBridgeDisable   <-              <-                ?    <-       ?         rsvd
 	 * 28    rsvd               DropOneClkOnRd  = SPIClkGate      ?    <-       ?         <-
-	 * 29:30 rsvd               <-              <-                ?    <-       ?         SpiReadMode[2:1]
+	 * 29:30 rsvd               <-              <-                ?    <-       ?         SpiReadMode[2:1]<1>
 	 * 31    rsvd               <-              SpiBusy           ?    <-       ?         <-
+	 *
+	 *  <1> see handle_speed
 	 */
 	tmp = mmio_readl(sb600_spibar + 0x00);
 	msg_pdbg("(0x%08" PRIx32 ") SpiArbEnable=%i", tmp, (tmp >> 19) & 0x1);
@@ -447,9 +502,6 @@ int sb600_probe_spi(struct pci_dev *dev)
 		return ERROR_NONFATAL;
 	}
 
-	tmp = (mmio_readb(sb600_spibar + 0xd) >> 4) & 0x3;
-	msg_pdbg("NormSpeed is %s MHz\n", speed_names[tmp]);
-
 	if (amd_gen >= CHIPSET_SB89XX) {
 		tmp = mmio_readb(sb600_spibar + 0x1D);
 		msg_pdbg("Using SPI_CS%d\n", tmp & 0x3);
@@ -494,6 +546,9 @@ int sb600_probe_spi(struct pci_dev *dev)
 		return 0;
 	}
 
+	if (handle_speed(dev) != 0)
+		return ERROR_FATAL;
+
 	if (sb600_handle_imc(dev, amd_imc_force) != 0)
 		return ERROR_FATAL;