1 files changed, 486 insertions, 0 deletions
diff --git a/FreeRTOS/Demo/CORTEX_MPU_M3_NUCLEO_L152RE_GCC/ST_Code/Drivers/STM32L1xx_HAL_Driver/Inc/stm32l1xx_hal_pwr.h b/FreeRTOS/Demo/CORTEX_MPU_M3_NUCLEO_L152RE_GCC/ST_Code/Drivers/STM32L1xx_HAL_Driver/Inc/stm32l1xx_hal_pwr.h
new file mode 100644
index 000000000..ec272057b
--- /dev/null
+++ b/FreeRTOS/Demo/CORTEX_MPU_M3_NUCLEO_L152RE_GCC/ST_Code/Drivers/STM32L1xx_HAL_Driver/Inc/stm32l1xx_hal_pwr.h
@@ -0,0 +1,486 @@
+/**
+  ******************************************************************************
+  * @file    stm32l1xx_hal_pwr.h
+  * @author  MCD Application Team
+  * @brief   Header file of PWR HAL module.
+  ******************************************************************************
+  * @attention
+  *
+  * <h2><center>&copy; Copyright (c) 2017 STMicroelectronics.
+  * All rights reserved.</center></h2>
+  *
+  * This software component is licensed by ST under BSD 3-Clause license,
+  * the "License"; You may not use this file except in compliance with the
+  * License. You may obtain a copy of the License at:
+  *                        opensource.org/licenses/BSD-3-Clause
+  *
+  ******************************************************************************
+  */
+
+/* Define to prevent recursive inclusion -------------------------------------*/
+#ifndef __STM32L1xx_HAL_PWR_H
+#define __STM32L1xx_HAL_PWR_H
+
+#ifdef __cplusplus
+ extern "C" {
+#endif
+
+/* Includes ------------------------------------------------------------------*/
+#include "stm32l1xx_hal_def.h"
+
+/** @addtogroup STM32L1xx_HAL_Driver
+  * @{
+  */
+
+/** @addtogroup PWR
+  * @{
+  */
+
+/* Exported types ------------------------------------------------------------*/
+
+/** @defgroup PWR_Exported_Types PWR Exported Types
+  * @{
+  */
+
+/**
+  * @brief  PWR PVD configuration structure definition
+  */
+typedef struct
+{
+  uint32_t PVDLevel;   /*!< PVDLevel: Specifies the PVD detection level.
+                            This parameter can be a value of @ref PWR_PVD_detection_level */
+
+  uint32_t Mode;      /*!< Mode: Specifies the operating mode for the selected pins.
+                           This parameter can be a value of @ref PWR_PVD_Mode */
+}PWR_PVDTypeDef;
+
+/**
+  * @}
+  */
+
+/* Internal constants --------------------------------------------------------*/
+
+/** @addtogroup PWR_Private_Constants
+  * @{
+  */
+#define PWR_EXTI_LINE_PVD  (0x00010000U)  /*!< External interrupt line 16 Connected to the PVD EXTI Line */
+
+/**
+  * @}
+  */
+
+
+
+/* Exported constants --------------------------------------------------------*/
+
+/** @defgroup PWR_Exported_Constants PWR Exported Constants
+  * @{
+  */
+
+/** @defgroup PWR_register_alias_address PWR Register alias address
+  * @{
+  */
+/* ------------- PWR registers bit address in the alias region ---------------*/
+#define PWR_OFFSET               (PWR_BASE - PERIPH_BASE)
+#define PWR_CR_OFFSET            0x00
+#define PWR_CSR_OFFSET           0x04
+#define PWR_CR_OFFSET_BB         (PWR_OFFSET + PWR_CR_OFFSET)
+#define PWR_CSR_OFFSET_BB        (PWR_OFFSET + PWR_CSR_OFFSET)
+/**
+  * @}
+  */
+
+/** @defgroup PWR_CR_register_alias PWR CR Register alias address
+  * @{
+  */
+/* --- CR Register ---*/
+/* Alias word address of LPSDSR bit */
+#define LPSDSR_BIT_NUMBER        POSITION_VAL(PWR_CR_LPSDSR)
+#define CR_LPSDSR_BB             ((uint32_t)(PERIPH_BB_BASE + (PWR_CR_OFFSET_BB * 32) + (LPSDSR_BIT_NUMBER * 4)))
+
+/* Alias word address of DBP bit */
+#define DBP_BIT_NUMBER           POSITION_VAL(PWR_CR_DBP)
+#define CR_DBP_BB                ((uint32_t)(PERIPH_BB_BASE + (PWR_CR_OFFSET_BB * 32) + (DBP_BIT_NUMBER * 4)))
+
+/* Alias word address of LPRUN bit */
+#define LPRUN_BIT_NUMBER         POSITION_VAL(PWR_CR_LPRUN)
+#define CR_LPRUN_BB              ((uint32_t)(PERIPH_BB_BASE + (PWR_CR_OFFSET_BB * 32) + (LPRUN_BIT_NUMBER * 4)))
+
+/* Alias word address of PVDE bit */
+#define PVDE_BIT_NUMBER          POSITION_VAL(PWR_CR_PVDE)
+#define CR_PVDE_BB               ((uint32_t)(PERIPH_BB_BASE + (PWR_CR_OFFSET_BB * 32) + (PVDE_BIT_NUMBER * 4)))
+
+/* Alias word address of FWU bit */
+#define FWU_BIT_NUMBER           POSITION_VAL(PWR_CR_FWU)
+#define CR_FWU_BB                ((uint32_t)(PERIPH_BB_BASE + (PWR_CR_OFFSET_BB * 32) + (FWU_BIT_NUMBER * 4)))
+
+/* Alias word address of ULP bit */
+#define ULP_BIT_NUMBER           POSITION_VAL(PWR_CR_ULP)
+#define CR_ULP_BB                ((uint32_t)(PERIPH_BB_BASE + (PWR_CR_OFFSET_BB * 32) + (ULP_BIT_NUMBER * 4)))
+/**
+  * @}
+  */
+
+/** @defgroup PWR_CSR_register_alias PWR CSR Register alias address
+  * @{
+  */
+
+/* --- CSR Register ---*/
+/* Alias word address of EWUP1, EWUP2 and EWUP3 bits */
+#define CSR_EWUP_BB(VAL)         ((uint32_t)(PERIPH_BB_BASE + (PWR_CSR_OFFSET_BB * 32) + (POSITION_VAL(VAL) * 4)))
+/**
+  * @}
+  */
+
+/** @defgroup PWR_PVD_detection_level PWR PVD detection level
+  * @{
+  */
+#define PWR_PVDLEVEL_0                  PWR_CR_PLS_LEV0
+#define PWR_PVDLEVEL_1                  PWR_CR_PLS_LEV1
+#define PWR_PVDLEVEL_2                  PWR_CR_PLS_LEV2
+#define PWR_PVDLEVEL_3                  PWR_CR_PLS_LEV3
+#define PWR_PVDLEVEL_4                  PWR_CR_PLS_LEV4
+#define PWR_PVDLEVEL_5                  PWR_CR_PLS_LEV5
+#define PWR_PVDLEVEL_6                  PWR_CR_PLS_LEV6
+#define PWR_PVDLEVEL_7                  PWR_CR_PLS_LEV7  /* External input analog voltage
+                                                            (Compare internally to VREFINT) */
+
+/**
+  * @}
+  */
+
+/** @defgroup PWR_PVD_Mode PWR PVD Mode
+  * @{
+  */
+#define PWR_PVD_MODE_NORMAL                 (0x00000000U)   /*!< basic mode is used */
+#define PWR_PVD_MODE_IT_RISING              (0x00010001U)   /*!< External Interrupt Mode with Rising edge trigger detection */
+#define PWR_PVD_MODE_IT_FALLING             (0x00010002U)   /*!< External Interrupt Mode with Falling edge trigger detection */
+#define PWR_PVD_MODE_IT_RISING_FALLING      (0x00010003U)   /*!< External Interrupt Mode with Rising/Falling edge trigger detection */
+#define PWR_PVD_MODE_EVENT_RISING           (0x00020001U)   /*!< Event Mode with Rising edge trigger detection */
+#define PWR_PVD_MODE_EVENT_FALLING          (0x00020002U)   /*!< Event Mode with Falling edge trigger detection */
+#define PWR_PVD_MODE_EVENT_RISING_FALLING   (0x00020003U)   /*!< Event Mode with Rising/Falling edge trigger detection */
+
+ /**
+ * @}
+  */
+
+/** @defgroup PWR_Regulator_state_in_SLEEP_STOP_mode PWR Regulator state in SLEEP/STOP mode
+  * @{
+  */
+#define PWR_MAINREGULATOR_ON           (0x00000000U)
+#define PWR_LOWPOWERREGULATOR_ON       PWR_CR_LPSDSR
+
+/**
+  * @}
+  */
+
+/** @defgroup PWR_SLEEP_mode_entry PWR SLEEP mode entry
+  * @{
+  */
+#define PWR_SLEEPENTRY_WFI             ((uint8_t)0x01)
+#define PWR_SLEEPENTRY_WFE             ((uint8_t)0x02)
+
+/**
+  * @}
+  */
+
+/** @defgroup PWR_STOP_mode_entry PWR STOP mode entry
+  * @{
+  */
+#define PWR_STOPENTRY_WFI              ((uint8_t)0x01)
+#define PWR_STOPENTRY_WFE              ((uint8_t)0x02)
+
+/**
+  * @}
+  */
+
+/** @defgroup PWR_Regulator_Voltage_Scale PWR Regulator Voltage Scale
+  * @{
+  */
+
+#define PWR_REGULATOR_VOLTAGE_SCALE1       PWR_CR_VOS_0
+#define PWR_REGULATOR_VOLTAGE_SCALE2       PWR_CR_VOS_1
+#define PWR_REGULATOR_VOLTAGE_SCALE3       PWR_CR_VOS
+
+
+/**
+  * @}
+  */
+
+/** @defgroup PWR_Flag PWR Flag
+  * @{
+  */
+#define PWR_FLAG_WU                    PWR_CSR_WUF
+#define PWR_FLAG_SB                    PWR_CSR_SBF
+#define PWR_FLAG_PVDO                  PWR_CSR_PVDO
+#define PWR_FLAG_VREFINTRDY            PWR_CSR_VREFINTRDYF
+#define PWR_FLAG_VOS                   PWR_CSR_VOSF
+#define PWR_FLAG_REGLP                 PWR_CSR_REGLPF
+
+/**
+  * @}
+  */
+
+/**
+  * @}
+  */
+
+/* Exported macro ------------------------------------------------------------*/
+/** @defgroup PWR_Exported_Macros PWR Exported Macros
+  * @{
+  */
+
+/** @brief  macros configure the main internal regulator output voltage.
+  * @param  __REGULATOR__ specifies the regulator output voltage to achieve
+  *         a tradeoff between performance and power consumption when the device does
+  *         not operate at the maximum frequency (refer to the datasheets for more details).
+  *          This parameter can be one of the following values:
+  *            @arg PWR_REGULATOR_VOLTAGE_SCALE1: Regulator voltage output Scale 1 mode,
+  *                                                System frequency up to 32 MHz.
+  *            @arg PWR_REGULATOR_VOLTAGE_SCALE2: Regulator voltage output Scale 2 mode,
+  *                                                System frequency up to 16 MHz.
+  *            @arg PWR_REGULATOR_VOLTAGE_SCALE3: Regulator voltage output Scale 3 mode,
+  *                                                System frequency up to 4.2 MHz
+  * @retval None
+  */
+#define __HAL_PWR_VOLTAGESCALING_CONFIG(__REGULATOR__) (MODIFY_REG(PWR->CR, PWR_CR_VOS, (__REGULATOR__)))
+
+/** @brief  Check PWR flag is set or not.
+  * @param  __FLAG__ specifies the flag to check.
+  *           This parameter can be one of the following values:
+  *            @arg PWR_FLAG_WU: Wake Up flag. This flag indicates that a wakeup event
+  *                  was received from the WKUP pin or from the RTC alarm (Alarm B),
+  *                  RTC Tamper event, RTC TimeStamp event or RTC Wakeup.
+  *                  An additional wakeup event is detected if the WKUP pin is enabled
+  *                  (by setting the EWUP bit) when the WKUP pin level is already high.
+  *            @arg PWR_FLAG_SB: StandBy flag. This flag indicates that the system was
+  *                  resumed from StandBy mode.
+  *            @arg PWR_FLAG_PVDO: PVD Output. This flag is valid only if PVD is enabled
+  *                  by the HAL_PWR_EnablePVD() function. The PVD is stopped by Standby mode
+  *                  For this reason, this bit is equal to 0 after Standby or reset
+  *                  until the PVDE bit is set.
+  *            @arg PWR_FLAG_VREFINTRDY: Internal voltage reference (VREFINT) ready flag.
+  *                 This bit indicates the state of the internal voltage reference, VREFINT.
+  *            @arg PWR_FLAG_VOS: Voltage Scaling select flag. A delay is required for
+  *                 the internal regulator to be ready after the voltage range is changed.
+  *                 The VOSF bit indicates that the regulator has reached the voltage level
+  *                 defined with bits VOS of PWR_CR register.
+  *            @arg PWR_FLAG_REGLP: Regulator LP flag. When the MCU exits from Low power run
+  *                 mode, this bit stays at 1 until the regulator is ready in main mode.
+  *                 A polling on this bit is recommended to wait for the regulator main mode.
+  *                 This bit is reset by hardware when the regulator is ready.
+  * @retval The new state of __FLAG__ (TRUE or FALSE).
+  */
+#define __HAL_PWR_GET_FLAG(__FLAG__) ((PWR->CSR & (__FLAG__)) == (__FLAG__))
+
+/** @brief  Clear the PWR's pending flags.
+  * @param  __FLAG__ specifies the flag to clear.
+  *          This parameter can be one of the following values:
+  *            @arg PWR_FLAG_WU: Wake Up flag
+  *            @arg PWR_FLAG_SB: StandBy flag
+  */
+#define __HAL_PWR_CLEAR_FLAG(__FLAG__) SET_BIT(PWR->CR, ((__FLAG__) << 2))
+
+/**
+  * @brief Enable interrupt on PVD Exti Line 16.
+  * @retval None.
+  */
+#define __HAL_PWR_PVD_EXTI_ENABLE_IT()      SET_BIT(EXTI->IMR, PWR_EXTI_LINE_PVD)
+
+/**
+  * @brief Disable interrupt on PVD Exti Line 16.
+  * @retval None.
+  */
+#define __HAL_PWR_PVD_EXTI_DISABLE_IT()     CLEAR_BIT(EXTI->IMR, PWR_EXTI_LINE_PVD)
+
+/**
+  * @brief Enable event on PVD Exti Line 16.
+  * @retval None.
+  */
+#define __HAL_PWR_PVD_EXTI_ENABLE_EVENT()   SET_BIT(EXTI->EMR, PWR_EXTI_LINE_PVD)
+
+/**
+  * @brief Disable event on PVD Exti Line 16.
+  * @retval None.
+  */
+#define __HAL_PWR_PVD_EXTI_DISABLE_EVENT()  CLEAR_BIT(EXTI->EMR, PWR_EXTI_LINE_PVD)
+
+
+/**
+  * @brief  PVD EXTI line configuration: set falling edge trigger.
+  * @retval None.
+  */
+#define __HAL_PWR_PVD_EXTI_ENABLE_FALLING_EDGE()  SET_BIT(EXTI->FTSR, PWR_EXTI_LINE_PVD)
+
+
+/**
+  * @brief Disable the PVD Extended Interrupt Falling Trigger.
+  * @retval None.
+  */
+#define __HAL_PWR_PVD_EXTI_DISABLE_FALLING_EDGE()  CLEAR_BIT(EXTI->FTSR, PWR_EXTI_LINE_PVD)
+
+
+/**
+  * @brief  PVD EXTI line configuration: set rising edge trigger.
+  * @retval None.
+  */
+#define __HAL_PWR_PVD_EXTI_ENABLE_RISING_EDGE()   SET_BIT(EXTI->RTSR, PWR_EXTI_LINE_PVD)
+
+/**
+  * @brief Disable the PVD Extended Interrupt Rising Trigger.
+  * @retval None.
+  */
+#define __HAL_PWR_PVD_EXTI_DISABLE_RISING_EDGE()  CLEAR_BIT(EXTI->RTSR, PWR_EXTI_LINE_PVD)
+
+/**
+  * @brief  PVD EXTI line configuration: set rising & falling edge trigger.
+  * @retval None.
+  */
+#define __HAL_PWR_PVD_EXTI_ENABLE_RISING_FALLING_EDGE()  \
+  do {                                                   \
+    __HAL_PWR_PVD_EXTI_ENABLE_RISING_EDGE();             \
+    __HAL_PWR_PVD_EXTI_ENABLE_FALLING_EDGE();            \
+  } while(0)
+
+/**
+  * @brief Disable the PVD Extended Interrupt Rising & Falling Trigger.
+  * @retval None.
+  */
+#define __HAL_PWR_PVD_EXTI_DISABLE_RISING_FALLING_EDGE()  \
+  do {                                                    \
+    __HAL_PWR_PVD_EXTI_DISABLE_RISING_EDGE();             \
+    __HAL_PWR_PVD_EXTI_DISABLE_FALLING_EDGE();            \
+  } while(0)
+
+
+
+/**
+  * @brief Check whether the specified PVD EXTI interrupt flag is set or not.
+  * @retval EXTI PVD Line Status.
+  */
+#define __HAL_PWR_PVD_EXTI_GET_FLAG()       (EXTI->PR & (PWR_EXTI_LINE_PVD))
+
+/**
+  * @brief Clear the PVD EXTI flag.
+  * @retval None.
+  */
+#define __HAL_PWR_PVD_EXTI_CLEAR_FLAG()     (EXTI->PR = (PWR_EXTI_LINE_PVD))
+
+/**
+  * @brief Generate a Software interrupt on selected EXTI line.
+  * @retval None.
+  */
+#define __HAL_PWR_PVD_EXTI_GENERATE_SWIT()  SET_BIT(EXTI->SWIER, PWR_EXTI_LINE_PVD)
+
+/**
+  * @}
+  */
+
+/* Private macro -------------------------------------------------------------*/
+/** @defgroup PWR_Private_Macros PWR Private Macros
+  * @{
+  */
+
+#define IS_PWR_PVD_LEVEL(LEVEL) (((LEVEL) == PWR_PVDLEVEL_0) || ((LEVEL) == PWR_PVDLEVEL_1)|| \
+                                 ((LEVEL) == PWR_PVDLEVEL_2) || ((LEVEL) == PWR_PVDLEVEL_3)|| \
+                                 ((LEVEL) == PWR_PVDLEVEL_4) || ((LEVEL) == PWR_PVDLEVEL_5)|| \
+                                 ((LEVEL) == PWR_PVDLEVEL_6) || ((LEVEL) == PWR_PVDLEVEL_7))
+
+
+#define IS_PWR_PVD_MODE(MODE) (((MODE) == PWR_PVD_MODE_IT_RISING)|| ((MODE) == PWR_PVD_MODE_IT_FALLING) || \
+                              ((MODE) == PWR_PVD_MODE_IT_RISING_FALLING) || ((MODE) == PWR_PVD_MODE_EVENT_RISING) || \
+                              ((MODE) == PWR_PVD_MODE_EVENT_FALLING) || ((MODE) == PWR_PVD_MODE_EVENT_RISING_FALLING) || \
+                              ((MODE) == PWR_PVD_MODE_NORMAL))
+
+#define IS_PWR_REGULATOR(REGULATOR) (((REGULATOR) == PWR_MAINREGULATOR_ON) || \
+                                     ((REGULATOR) == PWR_LOWPOWERREGULATOR_ON))
+
+
+#define IS_PWR_SLEEP_ENTRY(ENTRY) (((ENTRY) == PWR_SLEEPENTRY_WFI) || ((ENTRY) == PWR_SLEEPENTRY_WFE))
+
+#define IS_PWR_STOP_ENTRY(ENTRY) (((ENTRY) == PWR_STOPENTRY_WFI) || ((ENTRY) == PWR_STOPENTRY_WFE) )
+
+#define IS_PWR_VOLTAGE_SCALING_RANGE(RANGE) (((RANGE) == PWR_REGULATOR_VOLTAGE_SCALE1) || \
+                                             ((RANGE) == PWR_REGULATOR_VOLTAGE_SCALE2) || \
+                                             ((RANGE) == PWR_REGULATOR_VOLTAGE_SCALE3))
+
+
+/**
+  * @}
+  */
+
+
+
+/* Include PWR HAL Extension module */
+#include "stm32l1xx_hal_pwr_ex.h"
+
+/* Exported functions --------------------------------------------------------*/
+
+/** @addtogroup PWR_Exported_Functions PWR Exported Functions
+  * @{
+  */
+
+/** @addtogroup PWR_Exported_Functions_Group1 Initialization and de-initialization functions
+  * @{
+  */
+
+/* Initialization and de-initialization functions *******************************/
+void HAL_PWR_DeInit(void);
+void HAL_PWR_EnableBkUpAccess(void);
+void HAL_PWR_DisableBkUpAccess(void);
+
+/**
+  * @}
+  */
+
+/** @addtogroup PWR_Exported_Functions_Group2 Peripheral Control functions
+  * @{
+  */
+
+/* Peripheral Control functions  ************************************************/
+void HAL_PWR_ConfigPVD(PWR_PVDTypeDef *sConfigPVD);
+void HAL_PWR_EnablePVD(void);
+void HAL_PWR_DisablePVD(void);
+
+/* WakeUp pins configuration functions ****************************************/
+void HAL_PWR_EnableWakeUpPin(uint32_t WakeUpPinx);
+void HAL_PWR_DisableWakeUpPin(uint32_t WakeUpPinx);
+
+/* Low Power modes configuration functions ************************************/
+void HAL_PWR_EnterSTOPMode(uint32_t Regulator, uint8_t STOPEntry);
+void HAL_PWR_EnterSLEEPMode(uint32_t Regulator, uint8_t SLEEPEntry);
+void HAL_PWR_EnterSTANDBYMode(void);
+
+void HAL_PWR_EnableSleepOnExit(void);
+void HAL_PWR_DisableSleepOnExit(void);
+void HAL_PWR_EnableSEVOnPend(void);
+void HAL_PWR_DisableSEVOnPend(void);
+
+
+
+void HAL_PWR_PVD_IRQHandler(void);
+void HAL_PWR_PVDCallback(void);
+/**
+  * @}
+  */
+
+/**
+  * @}
+  */
+
+/**
+  * @}
+  */
+
+/**
+  * @}
+  */
+
+#ifdef __cplusplus
+}
+#endif
+
+
+#endif /* __STM32L1xx_HAL_PWR_H */
+
+/************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/