1 files changed, 0 insertions, 161 deletions
diff --git a/FreeRTOS/Demo/RX600_RX63N-RSK_Renesas/RTOSDemo/Renesas-Files/board/rskrx63n/hwsetup.c b/FreeRTOS/Demo/RX600_RX63N-RSK_Renesas/RTOSDemo/Renesas-Files/board/rskrx63n/hwsetup.c
deleted file mode 100644
index a72bd3fdd..000000000
--- a/FreeRTOS/Demo/RX600_RX63N-RSK_Renesas/RTOSDemo/Renesas-Files/board/rskrx63n/hwsetup.c
+++ /dev/null
@@ -1,161 +0,0 @@
-/***********************************************************************************************************************
-* DISCLAIMER
-* This software is supplied by Renesas Electronics Corporation and is only intended for use with Renesas products. No 
-* other uses are authorized. This software is owned by Renesas Electronics Corporation and is protected under all 
-* applicable laws, including copyright laws. 
-* THIS SOFTWARE IS PROVIDED "AS IS" AND RENESAS MAKES NO WARRANTIES REGARDING
-* THIS SOFTWARE, WHETHER EXPRESS, IMPLIED OR STATUTORY, INCLUDING BUT NOT LIMITED TO WARRANTIES OF MERCHANTABILITY, 
-* FITNESS FOR A PARTICULAR PURPOSE AND NON-INFRINGEMENT. ALL SUCH WARRANTIES ARE EXPRESSLY DISCLAIMED. TO THE MAXIMUM 
-* EXTENT PERMITTED NOT PROHIBITED BY LAW, NEITHER RENESAS ELECTRONICS CORPORATION NOR ANY OF ITS AFFILIATED COMPANIES 
-* SHALL BE LIABLE FOR ANY DIRECT, INDIRECT, SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES FOR ANY REASON RELATED TO THIS 
-* SOFTWARE, EVEN IF RENESAS OR ITS AFFILIATES HAVE BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.
-* Renesas reserves the right, without notice, to make changes to this software and to discontinue the availability of 
-* this software. By using this software, you agree to the additional terms and conditions found by accessing the 
-* following link:
-* http://www.renesas.com/disclaimer 
-*
-* Copyright (C) 2012 Renesas Electronics Corporation. All rights reserved.    
-***********************************************************************************************************************/
-/***********************************************************************************************************************
-* File Name	   : hwsetup.c
-* Device(s)    : RX
-* H/W Platform : RSK+RX63N
-* Description  : Defines the initialisation routines used each time the MCU is restarted.
-***********************************************************************************************************************/
-/***********************************************************************************************************************
-* History : DD.MM.YYYY Version  Description
-*         : 22.11.2011 1.00     First Release
-***********************************************************************************************************************/
-
-/***********************************************************************************************************************
-Includes   <System Includes> , "Project Includes"
-***********************************************************************************************************************/
-/* I/O Register and board definitions */
-#include "platform.h"
-/* Contains delcarations for the functions defined in this file */
-#include "hwsetup.h"
-
-/***********************************************************************************************************************
-Private global variables and functions
-***********************************************************************************************************************/
-/* MCU I/O port configuration function delcaration */
-static void output_ports_configure(void);
-
-/* Interrupt configuration function delcaration */
-static void interrupts_configure(void);
-
-/* MCU peripheral module configuration function declaration */
-static void peripheral_modules_enable(void);
-
-
-/***********************************************************************************************************************
-* Function name: hardware_setup
-* Description  : Contains setup functions called at device restart
-* Arguments    : none
-* Return value : none
-***********************************************************************************************************************/
-void hardware_setup(void)
-{
-    output_ports_configure();
-    interrupts_configure();
-    peripheral_modules_enable();
-}
-
-/***********************************************************************************************************************
-* Function name: output_ports_configure
-* Description  : Configures the port and pin direction settings, and sets the pin outputs to a safe level.
-* Arguments    : none
-* Return value : none
-***********************************************************************************************************************/
-void output_ports_configure(void)
-{
-    SYSTEM.PRCR.WORD = 0xA50B;			/* Protect off */
-    MPC.PWPR.BIT.B0WI = 0 ;     		/* Unlock protection register */
-    MPC.PWPR.BIT.PFSWE = 1 ;    		/* Unlock MPC registers */
-
-    /* Enable LEDs. */
-    /* Start with LEDs off. */
-    LED0 = LED_OFF;
-    LED1 = LED_OFF;
-    LED2 = LED_OFF;
-    LED3 = LED_OFF;
-
-    /* Set LED pins as outputs. */
-    LED0_PDR = 1;
-    LED1_PDR = 1;
-    LED2_PDR = 1;
-    LED3_PDR = 1;
-
-    /* Enable switches. */
-    /* Set pins as inputs. */
-    SW1_PDR = 0;
-    SW2_PDR = 0;
-    SW3_PDR = 0;
-
-    /* Set port mode registers for switches. */
-    SW1_PMR = 0;
-    SW2_PMR = 0;
-    SW3_PMR = 0;
-    
-    /* Initialize RSPI pins that are used with on-board SPI flash. */
-    /* Set pin outputs to low to begin with. */
-    PORT2.PODR.BIT.B7 = 0x00;    /* RSPCKB */
-    PORT2.PODR.BIT.B6 = 0x00;    /* MOSIB */
-    PORT3.PODR.BIT.B0 = 0x00;    /* MISOB */
-    PORT3.PODR.BIT.B1 = 0x00;    /* SSLB0 */
-    
-    /* All GPIO for now */
-    PORT2.PMR.BIT.B7 = 0x00;    
-    PORT2.PMR.BIT.B6 = 0x00;    
-    PORT3.PMR.BIT.B0 = 0x00;
-    PORT3.PMR.BIT.B1 = 0x00;
-
-    /* Unlock MPC registers to enable writing to them. */
-    MPC.PWPR.BIT.B0WI = 0 ;     /* Unlock protection register */
-    MPC.PWPR.BIT.PFSWE = 1 ;    /* Unlock MPC registers */
-        
-    /* Set MPC for RSPI pins */
-    MPC.P27PFS.BYTE = 0x0D;    
-    MPC.P26PFS.BYTE = 0x0D;    
-    MPC.P30PFS.BYTE = 0x0D;    
-    
-    /* RSPI pins assigned to RSPI peripheral. */
-    PORT2.PMR.BIT.B7 = 1;    
-    PORT2.PMR.BIT.B6 = 1;    
-    PORT3.PMR.BIT.B0 = 1;
-    PORT3.PMR.BIT.B1 = 1;    
-    
-    /* RSPCKB is output. */
-    PORT2.PDR.BIT.B7 = 1;
-    /* MOSIB is output. */
-    PORT2.PDR.BIT.B6 = 1;
-    /* MISOB is input. */
-    PORT3.PDR.BIT.B0 = 0;
-    /* SSLB0 is output. */
-    PORT3.PDR.BIT.B1 = 1;
-    
-    /* Configure the pin connected to the ADC Pot as an input */
-    PORT4.PDR.BIT.B0 = 0;
-}
-
-/***********************************************************************************************************************
-* Function name: interrupts_configure
-* Description  : Configures interrupts used
-* Arguments    : none
-* Return value : none
-***********************************************************************************************************************/
-void interrupts_configure(void)
-{
-    /* Add code here to setup additional interrupts */
-}
-
-/***********************************************************************************************************************
-* Function name: peripheral_modules_enable
-* Description  : Enables and configures peripheral devices on the MCU
-* Arguments    : none
-* Return value : none
-***********************************************************************************************************************/
-void peripheral_modules_enable(void)
-{
-    /* Add code here to enable peripherals used by the application */
-}